This subsystem id will be used later to turn on the btcoex
support.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The preferred module is p54pci which also supports FullMAC
PCI / Cardbus devices. We schedule removal for 2.6.34. Reason
to remove this is no one really is testing prism54 anymore,
and while it works p54pci provides support for the same hardware.
It should be noted I have been told some FullMAC devices may not
have worked with the SoftMAC driver but to date we have yet to
recieve a single bug report regarding this. If there are users
out there please let us know!

Cc: aquilaver@yahoo.com
Cc: linux-kernel@vger.kernel.org
Cc: Dan Williams <dcbw@redhat.com>
Cc: Kai Engert <kengert@redhat.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Cc: Tim de Waal<tim.dewaal@yahoo.com>
Cc: Roy Marples <uberlord@gentoo.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes some gcc warnings for switch statements.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes a sparse warning in the hardware-TKIP code:

drivers/net/wireless/b43/xmit.c:272:18: warning: incorrect type in assignment (different base types)
drivers/net/wireless/b43/xmit.c:272:18:    expected unsigned short [unsigned] [short] <noident>
drivers/net/wireless/b43/xmit.c:272:18:    got restricted unsigned short [usertype] <noident>

The code should work correctly with and without this patch applied.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, when QoS-disable is requested, we would leave QoS enabled
in firmware, but only queue frames on one queue.
Change that and also tell firmware about disabled QoS, so it
completely ignores all the QoS parameters. Also don't upload the parameters,
if QoS is disabled.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The calculated values for the ACK timeout and ACK
consume time are different then the values as
used by the Legacy drivers.

After testing from James Ledwith it appeared that
the calculated values caused a high amount of TX
failures, and the values from the Legacy drivers
were the most optimal to prevent TX failure due to
excessive retries.

The symptoms of this problem:
 - Rate control module always falls back to 1Mbs
 - Low throughput when bitrate was fixed

Possible side-effects (not confirmed but highly likely)
 - Problems with DHCP
 - Broken connections due to lack of probe response

This should fix at least:
Kernel bugzilla reports: [13362], [13009], [9273]
Fedora bugzilla reports: [443203]
but possible some additional bugs as well.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PCMCIA support works well and is not experimental anymore.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

apply the conformance test limits (CTL) stored in the eeprom upon
the values calculated for the tx power (ar->power_*).

This is based on the implementation in the vendor driver
(hal/hpmain.c, line 3700 ff.) with one difference:
If any ctl mode isn't found in the eeprom, we fall back to the "lower",
legacy modes (5GHT20,11A or 2GHT20,11G,11B). Otus only did 5GHT20->11A.

Currently CTL are applied for the FCC group only.
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ar9170 driver needs the defines for conformance test limit groups
and cannot include regd_common.h
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Acked-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the SHM spinlock.
SHM is protected by wl->mutex.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the PIO RX work. It's not needed anymore, because
we can sleep in the threaded interrupt handler.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the DMA/PIO queue locks. Locking is handled by
wl->mutex now.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This removes the TX spinlock and defers TX to a workqueue to allow
locking wl->mutex instead and to allow sleeping for register accesses.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a threaded IRQ handler to allow locking the mutex and
sleeping while executing an interrupt.
This removes usage of the irq_lock spinlock, but introduces
a new hardirq_lock, which is _only_ used for the PCI/SSB lowlevel
hard-irq handler. Sleeping busses (SDIO) will use mutex instead.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch ports some code from the vendor driver, which is
supposed to upload the right calibration values for the
chosen frequency.

In theory, this should give a better range and throughput
for all users with the open, or one-stage firmware.
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CHANNEL_G has to be set for 2GHZ channels since
IS_CHAN_G() checks for this in channelFlags and not in
chanmode. To make things messier, ath9k_hw_process_ini()
checks for CHANNEL_G in chanmode and not in channelFlags.
The supreme, brain-searing fix is to set the
flag in both cases.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BAR frames have to be sent to mac80211 only if the
current channel is HT. Also, move the macro to
enum ath9k_rx_filter.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k ahb requests an IRQ and indicates 'ath9k' claimed it,
ath9k pci requests an IRQ and indicates 'ath'   claims it;
since 'ath' is another module sync both ahb and pci to claim
the irq using 'ath9k'.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We've cleaned up ath_init_device() and its children enough
to pass meaninful errors back from probe. When this fails
it means our device could not be initialized and a meaninful
error will have been passed.

Do the same for request_irq() and also synchronize the error
messages while at it.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The -ENOMEM was never being passed on failure.
While at it use dev_err() as ahb does upon failure.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the initialisation of some PHY registers
from the modal_header[] values in the EEPROM
(see otus/hal/hpmain.c, line 333 ff.)
Signed-off-by: NJoerg Albert <jal2@gmx.de>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NNeil Horman <nhorman@txudriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change it to a menuconfig to give it some documentation, to
refer users to our wireless wiki for extra resources and
documentation. It seems our wiki is still obscure to some.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

No need to put ethtool_ops in data, they should be const.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to check what was the last fw error we got accross resets, we add
this debugfs entry. It displays the complete ASSERT information.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When UMAC stalls or asserts, we want to reset the device. But when we're
associated, the current reset worker will end up calling
cfg80211_connect_result() with the cfg80211 sme layer knowing that we're
reassociating. That ends up with some ugly warnings.
With this patch we're telling the upper layer that we've roamed if
reassociation succeeds, and that we're disconnected if it fails.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LMAC calibration API got broken mostly by having a configuration bitmap
being different than the result one.
This patch tries to address that issue by correctly running calibrations with
the newest firmwares, and keeping a backward compatibility fallback path for
older firmwares, where the configuration and result bitmaps were identical.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also mark some functions static.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the driver receives "connection terminated" event from device,
it could be caused by 2 reasons: the firmware is roaming or the
connection is lost (AP disappears). For the former, an association
complete event is supposed to come within 3 seconds. For the latter,
the driver won't receive any event except the connection terminated.
So we kick a delayed work (5*HZ) when we receive the connection
terminated event. It will be canceled if it turns out to be a roaming
event later. Otherwise we notify SME and userspace the disconnection.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The device sends connection terminated and [re]association success
(or failure) events when roaming occours. The patch uses
cfg80211_roamed instead of cfg80211_connect_result to notify SME
for roaming.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

iwm_cfg80211_get_station() should be static.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When connect is called with the LEGACY_PSK authentication type set, and a
proper sme->key, we need to set the WEP key straight after setting the
profile otherwise the authentication will never start.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If cfg80211 requests to connect when we have already had an active
profile, invalidate the current profile first before sending a new
profile to UMAC.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since rndis_wlan is now converted to cfg80211, WIRELESS_EXT isn't
required anymore.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

- remove double newlines between functions
- remove commented out function (rndis_set_config_parameter_u32())
- coding style fix in rndis_set_config_parameter_str()
- add comment banners between function sections
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>