In some cases kipmid can use a lot of CPU.  This adds a way to tune the
CPU used by kipmid to help in those cases.  By setting kipmid_max_busy_us
to a value between 100 and 500, it is possible to bring down kipmid CPU
load to practically 0 without loosing too much ipmi throughput
performance.  Not setting the value, or setting the value to zero,
operation is unaffected.
Signed-off-by: NMartin Wilck <martin.wilck@ts.fujitsu.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Today's -tip failed to build because commit
9e368fa0 ("ipmi: add PNP discovery (ACPI
namespace via PNPACPI)") from today's upstream kernel causes the following
build failure on x86, for CONFIG_ACPI=n && CONFIG_IPMI_SI=y:

 drivers/char/ipmi/ipmi_si_intf.c:3208: error: 'ipmi_pnp_driver' undeclared (first use in this function)
 drivers/char/ipmi/ipmi_si_intf.c:3208: error: (Each undeclared identifier is reported only once
 drivers/char/ipmi/ipmi_si_intf.c:3208: error: for each function it appears in.)
 drivers/char/ipmi/ipmi_si_intf.c:3334: error: 'ipmi_pnp_driver' undeclared (first use in this function)

The reason is that the ipmi_pnp_driver depends on ACPI facilities and is only
made available under ACPI - while the registration and unregistration is made
dependent on CONFIG_PNP:

 #ifdef CONFIG_PNP
 	pnp_register_driver(&ipmi_pnp_driver);
 #endif

The solution is to only register this driver under ACPI. (Also, the CONFIG_PNP
dependency is not needed because pnp_register_driver() is stubbed out in the
!CONFIG_PNP case.)
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NMyron Stowe <myron.stowe@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This allows ipmi_si_intf.c to claim IPMI devices described in the ACPI
namespace.  Using PNP makes it simpler to parse the IRQ/IO/memory resources
of the device.

We look at any SPMI tables before looking for devices in the namespace.

This is based on ipmi_pci_probe().
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NMyron Stowe <myron.stowe@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This discovery method uses the SPMI table, not the ACPI namespace.  In
the future, we will look in the namespace, so let's refer to the table
as "SPMI" and save "ACPI" for the namespace.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device.  Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used.  These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.

Cc: openipmi-developer@lists.sourceforge.net
Acked-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The IPMI driver would attempt to use the event buffer even if that
didn't exist on the BMC.  This patch modified the IPMI driver to check
for the event buffer's existence before trying to use it.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The wrong return value is being tested when allocating a platform device
in the IPMI SI code.  Check the right value.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.

We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.

But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.

->read_proc/->write_proc were just fixed to not require ->owner for
protection.

rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.

Removing ->owner will also make PDE smaller.

So, let's nuke it.

Kudos to Jeff Layton for reminding about this, let's say, oversight.

http://bugzilla.kernel.org/show_bug.cgi?id=12454Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>

It turns out that if one registers a struct platform_device, the
platform device code expects that platform_device.device->driver points
to a struct driver inside a struct platform_driver.

This is not the case with the ipmi-si, ipmi-msghandler and ibmaem
drivers, which causes the suspend/resume hook functions to jump off into
nowhere, causing a crash.  Make this assumption hold true for these
three drivers.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Acked-by: NCorey Minyard <cminyard@mvista.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms and we want to get rid of CONFIG_PPC_MERGE use
CONFIG_PPC instead.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

If check_legacy_ioport() returns true, we leak *info.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11362Reported-by: NDaniel Marjamki <danielm77@spray.se>
Cc: Christian Krafft <krafft@de.ibm.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Drivers should not include the asm variants anymore
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The current OF probing assumes that the resource is IORESOURCE_MEM.  This
checks for the IORESOURCE_IO flag and behaves appropriately.  An I/O resource
can exist with an ipmi device node on a legacy ISA bus.
Signed-off-by: NNate Case <ncase@xes-inc.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

IPMI code theoretically allows ->write_proc users, but nobody uses this thus
far.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Lots of style fixes for the IPMI system interface driver.  No functional
changes.  Basically fixes everything reported by checkpatch and fixes the
comment style.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Rocky Craig <rocky.craig@hp.com>
Cc: Hannes Schulz <schulz@schwaar.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert the #defines for statistics into an enum in the IPMI system interface
and remove the unused timeout_restart statistic.  And comment what these
statistics mean.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Atomics are faster and neater than locked counters.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch prevents deadlocks in IPMI panic handler caused by msg_lock
in smi_info structure and waiting_msgs_lock in ipmi_smi structure.

[cminyard@mvista.com: remove unnecessary memory barriers]
Signed-off-by: NKonstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The "run_to_completion" mode was somewhat broken.  Locks need to be avoided in
run_to_completion mode, and it shouldn't be used by normal users, just
internally for panic situations.

This patch removes locks in run_to_completion mode and removes the user call
for setting the mode.  The only user was the poweroff code, but it was easily
converted to use the polling interface.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hold handling of ATTN until the upper layer has reported that it is
ready.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for IPMI 0.9 systems to the IPMI driver.  Just handle a shorter
get device ID command with less information.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Stian Jordet <liste@jordet.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the IPMI watchdog timer sets the watchdog timeout on a panic, but it
doesn't actually poll the interface to make sure the message goes out.

Add an interface for polling the IPMI driver, and add code to the IPMI
watchdog timer to poll the interface when the timer is set from a panic.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patrick found a race at startup.  Interrupts were being enabled for the IPMI
interface before the driver was really ready to handle them.  This could
result in an oops if something was pending on the interface at startup and
interrupt were already enabled (technically shouldn't happen, but need to
cover for this in real life).  So move the IRQ setup to the code that starts
the actual IPMI processing.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

... should be unsigned int
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Three main sets of changes:

1) dmi_get_system_info() return value should have been marked const,
   since callers should not be changing that data.

2) const-ify DMI internals, since DMI firmware tables should,
   whenever possible, be marked const to ensure we never ever write to
   that data area.

3) const-ify DMI API, to enable marking tables const where possible
   in low-level drivers.

And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.

The bulk of the changes are #2 and #3, which are interrelated.  #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix a couple drivers that do not correctly terminate their pci_device_id
lists.  This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: NKees Cook <kees@ubuntu.com>
Acked-by: NCorey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

trivial change: fix warning
Signed-off-by: NMijo Safradin <safradin@de.ibm.com>
Acked-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

get_property has been renamed to of_get_property.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This is only called at init time and only happens if the BIOS screws
something up, so the leak is slight and it is probably not worth sending to
2.6.22.x.  The driver would not initialize the interface in the case, and I
have no reports of this happening.  I have booted and run tests on a system
with this patch.  Note that the original patch was munged by the mailer,
here's a new one.

If we ever hit the "default:" case in the switch in try_init_dmi(),
then we'll leak the storage allocated with kzalloc() and assigned
to 'info'.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDan Aloni <da-x@monatomic.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When trying to load the ipmi_si module on a powerpc with no BMC (baseboard
management controller) the driver failes to load correctly, but doesn't
unregister itself from of_platform.  So, on a second modprobe the kernel
crashes.  This patch adds the missing unregister call.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a rather obvious error that Patrick found in the setup routines.  Need to
set the proper address space in the ACPI case.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Cc: Patrick Schoeller <Patrick.Schoeller@hp.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add pci_remove handling to the driver, so it will clean up if
the device is hot-removed.
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The IPMI driver used enable_irq and disable_irq when it got into situations
where it couldn't allocate memory; it did this to avoid having the interrupt
just lock the machine when it couldn't get memory to perform the transaction
to disable the interrupt.

This patch modifies the driver to not use disable_irq and enable_irq.  It
instead sends the messages to the BMC to perform this operation.  It also
makes sure interrupts are cleanly disabled when the interface is shut down and
cleans up some shutdown things that are no longer necessary.
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for of_platform_driver to the ipmi_si module.  When loading the
module, the driver will be registered to of_platform.  The driver will be
probed for all devices with the type ipmi.  It's supporting devices with
compatible settings ipmi-kcs, ipmi-smic and ipmi-bt.  Only ipmi-kcs could be
tested.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Acked-by: NHeiko J Schick <schihei@de.ibm.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Acked-by: NArnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ipmi_si_intf tries to access default ports, if no device could be found
elsewhere.  On PPC we have a function to check, if these legacy IO ports
are accessible.  This patch adds a check for these ports on PPC.  This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: NChristian Krafft <krafft@de.ibm.com>
Acked-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLen Brown <len.brown@intel.com>

Fix various problems pointed out by Andrew Morton and others:
  * platform_device_unregister checks for NULL, no need to check here.
  * Formatting fixes.
  * Remove big macro and convert to a function.
  * Use strcmp instead of defining a broken case-insensitive comparison,
    and make the output parameter info match the case of the input one
    (change "I/O" to "i/o").
  * Return the length instead of 0 from the hotmod parameter handler.
  * Remove some unused cruft.
  * The trydefaults parameter only has to do with scanning the "standard"
    addresses, don't check for that on ACPI.
Signed-off-by: NCorey Minyard <cminyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Remove all =0 and =NULL from static initializers.  They are not needed and
removing them saves space in the object files.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NCorey Minyard <minyard@acm.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>