Merge tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix bug in DM crypt's sizing of its block integrity tag space,
   resulting in less memory use when DM crypt layers on DM integrity.

 - Fix a long-standing DM thinp crash consistency bug that was due to
   improper handling of FUA. This issue is specific to writes that fill
   an entire thinp block which needs to be allocated.

* tag 'for-5.0/dm-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm thin: fix bug where bio that overwrites thin block ignores FUA
  dm crypt: don't overallocate the integrity tag space

Pull MMC fixes from Ulf Hansson:
 "A couple of MMC fixes intended for v5.0-rc7.

  MMC core:
   - Fix deadlock bug for block I/O requests

  MMC host:
   - sunxi: Disable broken HS-DDR mode for H5 by default
   - sunxi: Avoid unsupported speed modes declared via DT
   - meson-gx: Restore interrupt name"

* tag 'mmc-v5.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: meson-gx: fix interrupt name
  mmc: block: handle complete_work on separate workqueue
  mmc: sunxi: Filter out unsupported modes declared in the device tree
  mmc: sunxi: Disable HS-DDR mode for H5 eMMC controller by default

Pull drm fixes from Dave Airlie:
 "Usual pull request, little larger than I'd like but nothing too
  strange in it. Willy found an bug in the lease ioctl calculations, but
  it's a drm master only ioctl which makes it harder to mess with.

 i915:
   - combo phy programming fix
   - opregion version check fix for VBT RVDA lookup
   - gem mmap ioctl race fix
   - fbdev hpd during suspend fix
   - array size bounds check fix in pmu

  amdgpu:
   - Vega20 psp fix
   - Add vrr range to debugfs for freesync debugging

  sched:
   - Scheduler race fix

  vkms:
   - license header fixups

  imx:
   - Fix CSI register offsets for i.MX51 and i.MX53.
   - Fix delayed page flip completion events on i.MX6QP due to
     unexpected behaviour of the PRE when issuing NOP buffer updates to
     the same buffer address.
   - Stop throwing errors for plane updates on disabled CRTCs when a
     userspace process is killed while a plane update is pending.
   - Add missing of_node_put cleanup in imx_ldb_bind"

* tag 'drm-fixes-2019-02-15-1' of git://anongit.freedesktop.org/drm/drm:
  drm: Use array_size() when creating lease
  drm/amdgpu/psp11: TA firmware is optional (v3)
  drm/i915/opregion: rvda is relative from opregion base in opregion 2.1+
  drm/i915/opregion: fix version check
  drm/i915: Prevent a race during I915_GEM_MMAP ioctl with WC set
  drm/i915: Block fbdev HPD processing during suspend
  drm/i915/pmu: Fix enable count array size and bounds checking
  drm/i915/cnl: Fix CNL macros for Voltage Swing programming
  drm/i915/icl: combo port vswing programming changes per BSPEC
  drm/vkms: Fix license inconsistent
  drm/amd/display: Expose connector VRR range via debugfs
  drm/sched: Always trace the dependencies we wait on, to fix a race.
  gpu: ipu-v3: pre: don't trigger update if buffer address doesn't change
  gpu: ipu-v3: Fix CSI offsets for imx53
  drm/imx: imx-ldb: add missing of_node_puts
  gpu: ipu-v3: Fix i.MX51 CSI control registers offset
  drm/imx: ignore plane updates on disabled crtcs

Pull crypto fix from Herbert Xu:
 "This fixes a crash on resume in the ccree driver"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ccree - fix resume race condition on init

Pull networking fixes from David Miller:

 1) Fix MAC address setting in mac80211 pmsr code, from Johannes Berg.

 2) Probe SFP modules after being attached, from Russell King.

 3) Byte ordering bug in SMC rx_curs_confirmed code, from Ursula Braun.

 4) Revert some r8169 changes that are causing regressions, from Heiner
    Kallweit.

 5) Fix spurious connection timeouts in netfilter nat code, from Florian
    Westphal.

 6) SKB leak in tipc, from Hoang Le.

 7) Short packet checkum issue in mlx4, similar to a previous mlx5
    change, from Saeed Mahameed. The issue is that whilst padding bytes
    are usually zero, it is not guarateed and the hardware doesn't take
    the padding bytes into consideration when generating the checksum.

 8) Fix various races in cls_tcindex, from Cong Wang.

 9) Need to set stream ext to NULL before freeing in SCTP code, from Xin
    Long.

10) Fix locking in phy_is_started, from Heiner Kallweit.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
  net: ethernet: freescale: set FEC ethtool regs version
  net: hns: Fix object reference leaks in hns_dsaf_roce_reset()
  mm: page_alloc: fix ref bias in page_frag_alloc() for 1-byte allocs
  net: phy: fix potential race in the phylib state machine
  net: phy: don't use locking in phy_is_started
  selftests: fix timestamping Makefile
  net: dsa: bcm_sf2: potential array overflow in bcm_sf2_sw_suspend()
  net: fix possible overflow in __sk_mem_raise_allocated()
  dsa: mv88e6xxx: Ensure all pending interrupts are handled prior to exit
  net: phy: fix interrupt handling in non-started states
  sctp: set stream ext to NULL after freeing it in sctp_stream_outq_migrate
  sctp: call gso_reset_checksum when computing checksum in sctp_gso_segment
  net/mlx5e: XDP, fix redirect resources availability check
  net/mlx5: Fix a compilation warning in events.c
  net/mlx5: No command allowed when command interface is not ready
  net/mlx5e: Fix NULL pointer derefernce in set channels error flow
  netfilter: nft_compat: use-after-free when deleting targets
  team: avoid complex list operations in team_nl_cmd_options_set()
  net_sched: fix two more memory leaks in cls_tcindex
  net_sched: fix a memory leak in cls_tcindex
  ...

Pull signal fix from Eric Biederman:
 "Just a single patch that restores PTRACE_EVENT_EXIT functionality that
  was accidentally broken by last weeks fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  signal: Restore the stop PTRACE_EVENT_EXIT

Passing an object_count of sufficient size will make
object_count * 4 wrap around to be very small, then a later function
will happily iterate off the end of the object_ids array.  Using
array_size() will saturate at SIZE_MAX, the kmalloc() will fail and
we'll return an -ENOMEM to the norty userspace.

Fixes: 62884cd3 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Signed-off-by: NMatthew Wilcox <willy@infradead.org>
Acked-by: NKees Cook <keescook@chromium.org>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: NDave Airlie <airlied@redhat.com>

amdgpu:
- Vega20 psp fix
- Add vrr range to debugfs for freesync debugging

sched:
- Scheduler race fix
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190213202958.3336-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2019-02-13' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.0-rc7:
- combo phy programming fix
- opregion version check fix for VBT RVDA lookup
- gem mmap ioctl race fix
- fbdev hpd during suspend fix
- array size bounds check fix in pmu
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877ee3504b.fsf@intel.com

drm-misc-fixes for v5.0:
- Fix license inconsistency in vkms.
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/812e2f53-d72a-8fba-6c8c-fde8f44cf141@linux.intel.com

When provisioning a new data block for a virtual block, either because
the block was previously unallocated or because we are breaking sharing,
if the whole block of data is being overwritten the bio that triggered
the provisioning is issued immediately, skipping copying or zeroing of
the data block.

When this bio completes the new mapping is inserted in to the pool's
metadata by process_prepared_mapping(), where the bio completion is
signaled to the upper layers.

This completion is signaled without first committing the metadata.  If
the bio in question has the REQ_FUA flag set and the system crashes
right after its completion and before the next metadata commit, then the
write is lost despite the REQ_FUA flag requiring that I/O completion for
this request must only be signaled after the data has been committed to
non-volatile storage.

Fix this by deferring the completion of overwrite bios, with the REQ_FUA
flag set, until after the metadata has been committed.

Cc: stable@vger.kernel.org
Signed-off-by: NNikos Tsironis <ntsironis@arrikto.com>
Acked-by: NJoe Thornber <ejt@redhat.com>
Acked-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

This reverts commit 8099b047.

It turns out that people do actually depend on the shebang string being
truncated, and on the fact that an interpreter (like perl) will often
just re-interpret it entirely to get the full argument list.
Reported-by: NSamuel Dionne-Riel <samuel@dionne-riel.com>
Acked-by: NKees Cook <keescook@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 2a5f14f2.

This patch causes xfstests generic/311 to fail. Reverting this for
now until we have a proper fix.
Signed-off-by: NAbhi Das <adas@redhat.com>
Signed-off-by: NBob Peterson <rpeterso@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently the ethtool_regs version is set to 0 for FEC devices.

Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:

        #if defined(CONFIG_M523x) || defined(CONFIG_M527x)
        || defined(CONFIG_M528x) || defined(CONFIG_M520x)
        || defined(CONFIG_M532x) || defined(CONFIG_ARM)
        || defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)

and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: NHuang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The basic idea behind ->pagecnt_bias is: If we pre-allocate the maximum
number of references that we might need to create in the fastpath later,
the bump-allocation fastpath only has to modify the non-atomic bias value
that tracks the number of extra references we hold instead of the atomic
refcount. The maximum number of allocations we can serve (under the
assumption that no allocation is made with size 0) is nc->size, so that's
the bias used.

However, even when all memory in the allocation has been given away, a
reference to the page is still held; and in the `offset < 0` slowpath, the
page may be reused if everyone else has dropped their references.
This means that the necessary number of references is actually
`nc->size+1`.

Luckily, from a quick grep, it looks like the only path that can call
page_frag_alloc(fragsz=1) is TAP with the IFF_NAPI_FRAGS flag, which
requires CAP_NET_ADMIN in the init namespace and is only intended to be
used for kernel testing and fuzzing.

To test for this issue, put a `WARN_ON(page_ref_count(page) == 0)` in the
`offset < 0` path, below the virt_to_page() call, and then repeatedly call
writev() on a TAP device with IFF_TAP|IFF_NO_PI|IFF_NAPI_FRAGS|IFF_NAPI,
with a vector consisting of 15 elements containing 1 byte each.
Signed-off-by: NJann Horn <jannh@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: fix locking issue

Russell pointed out that the locking used in phy_is_started() isn't
needed and misleading. This locking also contributes to a race fixed
with patch 2.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell reported the following race in the phylib state machine
(quoting from his mail):

if (phy_polling_mode(phydev) && phy_is_started(phydev))
	phy_queue_state_machine(phydev, PHY_STATE_TIME);

state = PHY_UP
thread 0			thread 1
				phy_disconnect()
				+-phy_is_started()
phy_is_started()                |
				`-phy_stop()
				  +-phydev->state = PHY_HALTED
				  `-phy_stop_machine()
				    `-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()

At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.

Fix this by protecting the complete operation in thread 0.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: NRussell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Suggested-by: NRussell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The clean target in the makefile conflicts with the generic
kselftests lib.mk, and fails to properly remove the compiled
test programs.

Remove the redundant rule, the TEST_GEN_FILES will be already
removed by the CLEAN macro in lib.mk.
Signed-off-by: NDeepa Dinamani <deepa.kernel@gmail.com>
Acked-by: NShuah Khan <shuah@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS.  The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions.  The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.

Fixes: 8cfa9498 ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With many active TCP sockets, fat TCP sockets could fool
__sk_mem_raise_allocated() thanks to an overflow.

They would increase their share of the memory, instead
of decreasing it.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge.  When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.

I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts).  Some interrupts are
directly cleared by reading the Global 1 status register.  However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.

The code only services interrupts whose status bit is set at the time of reading its status
register.  If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.

This is not a problem with polling or level interrupts since the handler will be called
again to process the event.  However, it's a big problem when using level interrupts.

The fix presented here is to add a loop around the code servicing switch interrupts.  If
any pending interrupts remain after the current set has been handled, we loop and process
the new set.  If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.

Tested on espressobin board.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: NJohn David Anglin <dave.anglin@bell.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.

Fixes: 2b3e88ea ("net: phy: improve phy state checking")
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In sctp_stream_init(), after sctp_stream_outq_migrate() freed the
surplus streams' ext, but sctp_stream_alloc_out() returns -ENOMEM,
stream->outcnt will not be set to 'outcnt'.

With the bigger value on stream->outcnt, when closing the assoc and
freeing its streams, the ext of those surplus streams will be freed
again since those stream exts were not set to NULL after freeing in
sctp_stream_outq_migrate(). Then the invalid-free issue reported by
syzbot would be triggered.

We fix it by simply setting them to NULL after freeing.

Fixes: 5bbbbe32 ("sctp: introduce stream scheduler foundations")
Reported-by: syzbot+58e480e7b28f2d890bfd@syzkaller.appspotmail.com
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jianlin reported a panic when running sctp gso over gre over vlan device:

  [   84.772930] RIP: 0010:do_csum+0x6d/0x170
  [   84.790605] Call Trace:
  [   84.791054]  csum_partial+0xd/0x20
  [   84.791657]  gre_gso_segment+0x2c3/0x390
  [   84.792364]  inet_gso_segment+0x161/0x3e0
  [   84.793071]  skb_mac_gso_segment+0xb8/0x120
  [   84.793846]  __skb_gso_segment+0x7e/0x180
  [   84.794581]  validate_xmit_skb+0x141/0x2e0
  [   84.795297]  __dev_queue_xmit+0x258/0x8f0
  [   84.795949]  ? eth_header+0x26/0xc0
  [   84.796581]  ip_finish_output2+0x196/0x430
  [   84.797295]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.798183]  ? ip_finish_output+0x169/0x270
  [   84.798875]  ip_output+0x6c/0xe0
  [   84.799413]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.800145]  iptunnel_xmit+0x144/0x1c0
  [   84.800814]  ip_tunnel_xmit+0x62d/0x930 [ip_tunnel]
  [   84.801699]  gre_tap_xmit+0xac/0xf0 [ip_gre]
  [   84.802395]  dev_hard_start_xmit+0xa5/0x210
  [   84.803086]  sch_direct_xmit+0x14f/0x340
  [   84.803733]  __dev_queue_xmit+0x799/0x8f0
  [   84.804472]  ip_finish_output2+0x2e0/0x430
  [   84.805255]  ? skb_gso_validate_network_len+0x11/0x80
  [   84.806154]  ip_output+0x6c/0xe0
  [   84.806721]  ? ip_append_data.part.50+0xc0/0xc0
  [   84.807516]  sctp_packet_transmit+0x716/0xa10 [sctp]
  [   84.808337]  sctp_outq_flush+0xd7/0x880 [sctp]

It was caused by SKB_GSO_CB(skb)->csum_start not set in sctp_gso_segment.
sctp_gso_segment() calls skb_segment() with 'feature | NETIF_F_HW_CSUM',
which causes SKB_GSO_CB(skb)->csum_start not to be set in skb_segment().

For TCP/UDP, when feature supports HW_CSUM, CHECKSUM_PARTIAL will be set
and gso_reset_checksum will be called to set SKB_GSO_CB(skb)->csum_start.

So SCTP should do the same as TCP/UDP, to call gso_reset_checksum() when
computing checksum in sctp_gso_segment.
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for net:

1) Missing structure initialization in ebtables causes splat with
   32-bit user level on a 64-bit kernel, from Francesco Ruggeri.

2) Missing dependency on nf_defrag in IPVS IPv6 codebase, from
   Andrea Claudi.

3) Fix possible use-after-free from release path of target extensions.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-02-13

This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).

To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.

The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.

Fixes: 58b99ee3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: NToke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Eliminate the following compilation warning:

drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]:  => 238:3

Fixes: c2fb3db2 ("net/mlx5: Rework handling of port module events")
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reviewed-by: NMikhael Goikhman <migo@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.

Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.

Fixes: c1d4d2e9 ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: NHuy Nguyen <huyn@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.

The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.

This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.

Fixes: bbeb53b8 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: NMaria Pasechnik <mariap@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Pull tracing fix from Steven Rostedt:
 "This fixes kprobes/uprobes dynamic processing of strings, where it
  processes the args but does not update the remaining length of the
  buffer that the string arguments will be placed in. It constantly
  passes in the total size of buffer used instead of passing in the
  remaining size of the buffer used.

  This could cause issues if the strings are larger than the max size of
  an event which could cause the strings to be written beyond what was
  reserved on the buffer"

* tag 'trace-v5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: probeevent: Correctly update remaining space in dynamic area

Fetch pointer to module before target object is released.

Fixes: 29e38801 ("netfilter: nf_tables: fix use-after-free when deleting compat expressions")
Fixes: 0ca743a5 ("netfilter: nf_tables: add compatibility layer for x_tables")
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Don't warn or fail if it's missing.

v2: handle xgmi case more gracefully.
v3: handle older kernels properly
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Tested-by: NJames Zhu <James.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In the middle of do_exit() there is there is a call
"ptrace_event(PTRACE_EVENT_EXIT, code);" That call places the process
in TACKED_TRACED aka "(TASK_WAKEKILL | __TASK_TRACED)" and waits for
for the debugger to release the task or SIGKILL to be delivered.

Skipping past dequeue_signal when we know a fatal signal has already
been delivered resulted in SIGKILL remaining pending and
TIF_SIGPENDING remaining set.  This in turn caused the
scheduler to not sleep in PTACE_EVENT_EXIT as it figured
a fatal signal was pending.  This also caused ptrace_freeze_traced
in ptrace_check_attach to fail because it left a per thread
SIGKILL pending which is what fatal_signal_pending tests for.

This difference in signal state caused strace to report
strace: Exit of unknown pid NNNNN ignored

Therefore update the signal handling state like dequeue_signal
would when removing a per thread SIGKILL, by removing SIGKILL
from the per thread signal mask and clearing TIF_SIGPENDING.
Acked-by: NOleg Nesterov <oleg@redhat.com>
Reported-by: NOleg Nesterov <oleg@redhat.com>
Reported-by: NIvan Delalande <colona@arista.com>
Cc: stable@vger.kernel.org
Fixes: 35634ffa ("signal: Always notice exiting tasks")
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>

Commit bb364890 ("mmc: meson-gx: Free irq in release() callback")
changed the _probe code to use request_threaded_irq() instead of
devm_request_threaded_irq().
Unfortunately this removes a fallback for the interrupt name:
devm_request_threaded_irq() uses the device name as fallback if the
given IRQ name is NULL. request_threaded_irq() has no such fallback,
thus /proc/interrupts shows "(null)" instead.

Explicitly pass the dev_name() so we get the IRQ name shown in
/proc/interrupts again.
While here, also fix the indentation of the request_threaded_irq()
parameter list.

Fixes: bb364890 ("mmc: meson-gx: Free irq in release() callback")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

drm/imx: plane, ldb, and ipu-v3 fixes

- Fix CSI register offsets for i.MX51 and i.MX53.
- Fix delayed page flip completion events on i.MX6QP due to unexpected
  behaviour of the PRE when issuing NOP buffer updates to the same
  buffer address.
- Stop throwing errors for plane updates on disabled CRTCs when a
  userspace process is killed while a plane update is pending.
- Add missing of_node_put cleanup in imx_ldb_bind.
Signed-off-by: NDave Airlie <airlied@redhat.com>

From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1549990602.4800.11.camel@pengutronix.de

Merge fixes from Andrew Morton:
 "6 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: proc: smaps_rollup: fix pss_locked calculation
  Rename include/{uapi => }/asm-generic/shmparam.h really
  Revert "mm: use early_pfn_to_nid in page_ext_init"
  mm/gup: fix gup_pmd_range() for dax
  Revert "mm: slowly shrink slabs with a relatively small number of objects"
  Revert "mm: don't reclaim inodes with many attached pages"

The 'pss_locked' field of smaps_rollup was being calculated incorrectly.
It accumulated the current pss everytime a locked VMA was found.  Fix
that by adding to 'pss_locked' the same time as that of 'pss' if the vma
being walked is locked.

Link: http://lkml.kernel.org/r/20190203065425.14650-1-sspatil@android.com
Fixes: 493b0e9d ("mm: add /proc/pid/smaps_rollup")
Signed-off-by: NSandeep Patil <sspatil@android.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Reviewed-by: NJoel Fernandes (Google) <joel@joelfernandes.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Daniel Colascione <dancol@google.com>
Cc: <stable@vger.kernel.org>	[4.14.x, 4.19.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>