It's incorrect to do soft reset for SRIOV, when GFX
hang the WREG would stuck there becuase it goes KIQ way.

the GPU reset counter is incorrect: always increase twice
for each timedout
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Since Hardware bug, GDS exist ECC error after cold boot up,
adding GDS clearing workaround in later init for gfx9.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Whenever the a modeset is allowed (but not neccessarily required) we
currently recreate all the planes in the state. Most IGT tests and
legacy IOCTLs create atomic commits with this flag set, so the pipes
are often unnecessarily reprogrammed.

Poor performance and stuttering can occur when many of these commits
are frequently issued.

This flag was needed when the appropriate conditions for checking
whether the planes needed a reset were not in place, but
should_reset_plane should cover everything needed now.

[How]
Drop the check for state->allow_modeset in should_reset_plane.

All planes on a CRTC should reset in the following conditions:
- The CRTC needs a modeset
- The CRTC degamma changes
- Planes are added or removed to the CRTC

These conditions are all covered in should_reset_plane.

We still can't drop the format change check in should_reset_plane since
fill_dc_plane_info_and_addr isn't called when validating the state, so
we can't tell if a FULL update is needed or not.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDavid Francis <david.francis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The old logic for checking which output depth to use relied on using
the current connector state rather than the new proposed state. This
was a problem when performing atomic commits since we weren't verifying
it against the incoming max_requested_bpc.

But switching this to only use the new state and not the current state
breaks filtering modes - it'll always assume that the maximum bpc
supported by the display is in use, which will cause certain modes
like 1440p@144Hz to be filtered even when using 8bpc.

[How]
Still use the connector->state if we aren't passed an explicit state.
This will respect the max_bpc the user currently has when filtering
modes.

Also remember to reset the default max_requested_bpc to 8 whenever
connector reset is called to retain old behavior when using the new
property.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110845Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This option is no longer needed.  The default code paths
are now the only option.

v2: Add HPAGE support and a default for non contiguous maps
v3: Misread 512 pages as MiB ...
Signed-off-by: NTom St Denis <tom.stdenis@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.

We need an initial connector state on the connector to avoid the crash.

[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
This will be useful for verifying whether we enter the correct output
color depth from IGT.

[How]
Locks the connector and associated CRTC if available and outputs
the current and maximum output bpc values.

Example:

cat /sys/kernel/debug/dri/0/DP-1/output_bpc
Current: 8
Maximum: 10

v2: Drop unneeded connector status check
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NDavid Francis <David.Francis@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use SMU firmware version to indentify the raven1 refresh device and
then load homologous RLC FW.
Signed-off-by: NPrike Liang <Prike.Liang@amd.com>
Suggested-by: Huang Rui<Ray.Huang@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add gfxoff_state_changed_by_workload to control gfxoff
when set power_profile_mode
Signed-off-by: NChengming Gui <Jack.Gui@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Under Vega10 SR-IOV VF, L1 register access mode should be enabled by
default as the non-security VF will no longer be supported.
Signed-off-by: NTrigger Huang <Trigger.Huang@amd.com>
Reviewed-by: NEmily Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[What]
readptr read always returns zero, since most likely
these blocks are either power or clock gated.

[How]
fetch rptr after amdgpu_ring_alloc() which informs
the power management code that the block is about to be
used and hence the gating is turned off.
Signed-off-by: NLouis Li <Ching-shih.Li@amd.com>
Signed-off-by: NShirish S <shirish.s@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[What]
vce ring test fails consistently during resume in s3 cycle, due to
mismatch read & write pointers.
On debug/analysis its found that rptr to be compared is not being
correctly updated/read, which leads to this failure.
Below is the failure signature:
	[drm:amdgpu_vce_ring_test_ring] *ERROR* amdgpu: ring 12 test failed
	[drm:amdgpu_device_ip_resume_phase2] *ERROR* resume of IP block <vce_v3_0> failed -110
	[drm:amdgpu_device_resume] *ERROR* amdgpu_device_ip_resume failed (-110).

[How]
fetch rptr appropriately, meaning move its read location further down
in the code flow.
With this patch applied the s3 failure is no more seen for >5k s3 cycles,
which otherwise is pretty consistent.

V2: remove reduntant fetch of rptr
Signed-off-by: NLouis Li <Ching-shih.Li@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Ported from gfx8, no changes in register setup.
Signed-off-by: NJay Cornwall <Jay.Cornwall@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Translate queue priority into pipe priority and write to MQDs.
The priority values are used to perform queue and pipe arbitration.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Always mark evicted queues with q->properties.is_evicted = true, even
queues that are inactive for other reason. This simplifies maintaining
the eviction state as it doesn't require updating is_evicted when other
queue activation conditions change.

On the other hand, we now need to check those other queue activation
conditions whenever an evicted queues is restored. To minimize code
duplication, move the queue activation check into a macro so it can be
maintained in one central place.
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NPhilip Cox <Philip.Cox@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

EDC counts are related to instance and se. They are not the same
for different type of EDC. EDC clearing are changed to base on
individual EDC's instance and SE number.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DCN_VERSION_1_01 is no longer handled in the dal_hw_translate_init
switch since it was inadvertently dropped in the patch that removed the
unnecessary DCN1_01 guards.

This caused numerous regressions on DCN1_01 when loading the driver.

[How]
Add it back.

Fixes: 97df424f ("drm/amd/display: Drop DCN1_01 guards")
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When switching from vt to desktop with EDID emulation we can receive
an atomic commit such that we have a crtc where mode_changed = true.

During the dm_update_crtc_state disable pass we remove the stream from
the context and free it on the dm_new_crtc_state.

During the enable pass we compare the new provisional stream to the
dm_old_crtc_state->stream and determine that the stream is unchanged
and no scaling has been changed.

Following this, new_crtc_state->mode_changed is then set to false.
The connectors haven't changed and the CRTC active state hasn't changed
so drm_atomic_crtc_needs_modeset returns false, so we jump to
skip_modeset and we hit:

BUG_ON(dm_new_crtc_state->stream == NULL);

...since the old stream is gone from the context and the new stream is
also still NULL.

[How]
Ensure that we still a stream to reuse before checking if we can reuse
the old stream without a full modeset.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This avoids OOM situations when we have lots of threads
submitting at the same time.

v3: apply this to the whole driver, not just CS
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

And only move them in on validation. This allows for better control
when multiple processes are fighting over those resources.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The messages about amdgpu_cs_list_validate are duplicated because the
caller will complain into the logs as well and we can also get
interrupted by a signal here.

Also fix the the caller to not report -EAGAIN from validation.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ras ta interface header need to be updated to match with latest ta fw updates
Signed-off-by: NHawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This reverts commit 8d8a5a64.

Wait until KHR exposes the VLK support.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

These got added back by subsequent merges accidently.
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Split late_init into two functions, one (do_late_init) which
just does the hw init, and late_init which calls do_late_init
and schedules the IB test work.  Call do_late_init in
the GPU reset code to run the init code, but not schedule
the IB test code.  The IB test code is called directly
in the gpu reset code so no need to run the IB tests
in a separate work thread.  If we do, we end up racing.

v2: Rework late_init.  Pull out the mgpu fan boost and xgmi
pstate code into late_init so they get called in all cases.
rename the late_init worker thread to delayed work since it's
just the IB tests now which can happen later.  Schedule the
work at init and resume time.  It's not needed at reset time
because the IB tests are called directly.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Cc: Xinhui Pan <xinhui.pan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

gpu reset will run late_init and schedule the late_init_work.  if we
keep triggering gpu reset in a short time, there are potenial races.
Signed-off-by: Nxinhui pan <xinhui.pan@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We can issue HDR static metadata as part of stream updates for
non-modesets as long as we force a modeset when entering or exiting HDR.

This avoids unnecessary blanking for simple metadata updates.

[How]
When changing scaling and abm for the stream also check if HDR has
changed and send the stream update. This will only happen in non-modeset
cases.

Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-3-nicholas.kazlauskas@amd.com

[Why]
For userspace to send static HDR metadata to the display we need to
attach the property on the connector and send it to DC.

[How]
The property is attached to HDMI and DP connectors. Since the metadata
isn't actually available when creating the connector this isn't a
property we can dynamically support based on the extension block
being available or not.

When the HDR metadata is changed a modeset will be forced for now.
We need to switch from 8bpc to 10bpc in most cases anyway, and we want
to fully exit HDR mode when userspace gives us a NULL metadata, so this
isn't completely unnecessary.

The requirement can later be reduced to just entering and exiting HDR
or switching max bpc.

Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NHarry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528190836.10738-2-nicholas.kazlauskas@amd.com

add ticket for display bo, so that it can preempt busy bo.

v2: fix stupid rebase error
Signed-off-by: NChunming Zhou <david1.zhou@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We are already doing this for DMA-buf imports and also for
amdgpu VM BOs for quite a while now.

If this doesn't run into any problems we are probably going
to stop removing BOs from the LRU altogether.

v2: drop BUG_ON from ttm_bo_add_to_lru
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Tested-by: NPierre-Eric Pelloux-Prayer <pierre-eric.pelloux-prayer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Issue:
Will have follow error when reload driver:
[ 3986.567739] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:07.0/drm_dp_aux_dev'
[ 3986.567743] CPU: 6 PID: 1767 Comm: modprobe Tainted: G           OE     5.0.0-rc1-custom #1
[ 3986.567745] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 3986.567746] Call Trace:
......
[ 3986.567808]  drm_dp_aux_register_devnode+0xdc/0x140 [drm_kms_helper]
......
[ 3986.569081] kobject_add_internal failed for drm_dp_aux_dev with -EEXIST, don't try to register things with the same name in the same directory.

Reproduce sequences:
1.modprobe amdgpu
2.modprobe -r amdgpu
3.modprobe amdgpu

Root cause:
When unload driver, it doesn't unregister aux.

v2: Don't use has_aux
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

For the VF, some registers only could be programmed with RLC.
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NTrigger Huang <Trigger.Huang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We only want to manual trigger end-of-frame when the bottom-most
pipe is flipped to prevent overlays from ending the frame too early.

[How]
Check that the manual trigger is only firing on bottom plane.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There's some unnecessary mem allocation for CS_TFM_ID. What's worse, it
depends on LUT size and since it's 4K for CS_TFM_1D, it is 16x bigger
than in regular case when it's actually needed. This leads to some
crashes in stress conditions.

[How]
Skip ramp combining designed for RGB256 and DXGI gamma with CS_TFM_1D.
Signed-off-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
For commits with allow_modeset=false and CRTC degamma changes the planes
aren't reset. This results in incorrect rendering.

[How]
Reset the planes when color management has changed on the CRTC.
Technically this will include regamma changes as well, but it doesn't
really after legacy userspace since those commit with
allow_modeset=true.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some backlight tests fail due to backlight settling
taking too long. This happens because the step
size used to change backlight levels is too small.

[How]
1. Change the size of the backlight gain step size
2. Change how DMCU firmware gets the step size value
   so that it is passed in by driver during DMCU initn
Signed-off-by: NEryk Brol <eryk.brol@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some displays take some time to power up AUX CH once they are
put into D3 state via write to DPCD 600h=2.

Interestingly enough, some display may simply NACK, but some might
also ACK with a bunch of 0s, which can cause issues with receiver
cap retrieval. Note that not all DPCD address return 0s, but in
particular it has been observed on some higher DPCD address such
as DPCD 2200h, etc.

[How]
Based on spec, receiver will monitor differential signal while in D3 and
AUX CH is in low power mode. When detected, it may allow up to
1 ms to power up AUX CH and reply.

If we read Sink power state D3, we should add 1 ms delay to satisfy
this spec requirement.
Signed-off-by: NAnthony Koo <anthony.koo@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

* Pull duplicate audio_clock_info struct to stream_encoder.h
* Generalize sec_gsp7* to sec_gsp_pps*
* Expose enc1 and enc2 stream encoder audio funcs
Signed-off-by: NEric Bernstein <eric.bernstein@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description] This is cause by failing to read link caps from driver.
Signed-off-by: NDaniel He <daniel.he@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>