- 05 12月, 2012 3 次提交
-
-
由 Nicolas Dichtel 提交于
These statistics can be checked only via /proc/net/ip_mr_cache or SIOCGETSGCNT[_IN6] and thus only for the table RT_TABLE_DEFAULT. Advertising them via rtnetlink allows to get statistics for all cache entries, whatever the table is. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
This patch removes the skb manipulations when nested attributes are added by using standard helpers. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nicolas Dichtel 提交于
This patch advertise the MC_FORWARDING status for IPv4 and IPv6. This field is readonly, only multicast engine in the kernel updates it. Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2012 3 次提交
-
-
由 Paul Marks 提交于
I believe this commit from 2008 was incorrect: http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=398bcbebb6f721ac308df1e3d658c0029bb74503 When CONFIG_IPV6_ROUTER_PREF is disabled, the kernel should follow RFC4861 section 6.3.6: if no route is NUD_VALID, then traffic should be sprayed across all routers (indirectly triggering NUD) until one of them becomes NUD_VALID. However, the following experiment demonstrates that this does not work: 1) Connect to an IPv6 network. 2) Change the router's MAC (and link-local) address. The kernel will lock onto the first router and never try the new one, even if the first becomes unreachable. This patch fixes the problem by allowing rt6_check_neigh() to return 0; if all routers return 0, then rt6_select() will fall back to round-robin behavior. This patch should have no effect when CONFIG_IPV6_ROUTER_PREF=y. Note that rt6_check_neigh() is only used in a boolean context, so I've changed its return type accordingly. Signed-off-by: NPaul Marks <pmarks@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Shmulik Ladkani 提交于
ipv6: Make 'addrconf_rs_timer' send Router Solicitations (and re-arm itself) if Router Advertisements are accepted As of 026359bc [ipv6: Send ICMPv6 RSes only when RAs are accepted], Router Solicitations are sent whenever kernel accepts Router Advertisements on the interface. However, this logic isn't reflected in 'addrconf_rs_timer'. The timer fails to issue subsequent RS messages (and fails to re-arm itself) if forwarding is enabled and the special hybrid mode is enabled (accept_ra=2). Fix the condition determining whether next RS should be sent, by using 'ipv6_accept_ra()'. Reported-by: NAmi Koren <amikoren@yahoo.com> Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michele Baldessari 提交于
The current SCTP stack is lacking a mechanism to have per association statistics. This is an implementation modeled after OpenSolaris' SCTP_GET_ASSOC_STATS. Userspace part will follow on lksctp if/when there is a general ACK on this. V4: - Move ipackets++ before q->immediate.func() for consistency reasons - Move sctp_max_rto() at the end of sctp_transport_update_rto() to avoid returning bogus RTO values - return asoc->rto_min when max_obs_rto value has not changed V3: - Increase ictrlchunks in sctp_assoc_bh_rcv() as well - Move ipackets++ to sctp_inq_push() - return 0 when no rto updates took place since the last call V2: - Implement partial retrieval of stat struct to cope for future expansion - Kill the rtxpackets counter as it cannot be precise anyway - Rename outseqtsns to outofseqtsns to make it clearer that these are out of sequence unexpected TSNs - Move asoc->ipackets++ under a lock to avoid potential miscounts - Fold asoc->opackets++ into the already existing asoc check - Kill unneeded (q->asoc) test when increasing rtxchunks - Do not count octrlchunks if sending failed (SCTP_XMIT_OK != 0) - Don't count SHUTDOWNs as SACKs - Move SCTP_GET_ASSOC_STATS to the private space API - Adjust the len check in sctp_getsockopt_assoc_stats() to allow for future struct growth - Move association statistics in their own struct - Update idupchunks when we send a SACK with dup TSNs - return min_rto in max_rto when RTO has not changed. Also return the transport when max_rto last changed. Signed-off: Michele Baldessari <michele@acksyn.org> Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 12月, 2012 7 次提交
-
-
由 Jozsef Kadlecsik 提交于
When the route changes (backup default route, VPNs) which affect a masqueraded target, the packets were sent out with the outdated source address. The patch addresses the issue by comparing the outgoing interface directly with the masqueraded interface in the nat table. Events are inefficient in this case, because it'd require adding route events to the network core and then scanning the whole conntrack table and re-checking the route for all entry. Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Florian Westphal 提交于
Add stricter checking for a few attributes. Note that these changes don't fix any bug in the current code base. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Florian Westphal 提交于
We used to have several queueing backends, but nowadays only nfnetlink_queue remains. In light of this there doesn't seem to be a good reason to support per-af registering -- just hook up nfnetlink_queue on module load and remove it on unload. This means that the userspace BIND/UNBIND_PF commands are now obsolete; the kernel will ignore them. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Pablo Neira Ayuso 提交于
This patch adds a new operation to dump the content of the dying and unconfirmed lists. Under some situations, the global conntrack counter can be inconsistent with the number of entries that we can dump from the conntrack table. The way to resolve this is to allow dumping the content of the unconfirmed and dying lists, so far it was not possible to look at its content. This provides some extra instrumentation to resolve problematic situations in which anyone suspects memory leaks. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Pablo Neira Ayuso 提交于
This patch modifies the conntrack subsystem so that all existing allocated conntrack objects can be found in any of the following places: * the hash table, this is the typical place for alive conntrack objects. * the unconfirmed list, this is the place for newly created conntrack objects that are still traversing the stack. * the dying list, this is where you can find conntrack objects that are dying or that should die anytime soon (eg. once the destroy event is delivered to the conntrackd daemon). Thus, we make sure that we follow the track for all existing conntrack objects. This patch, together with some extension of the ctnetlink interface to dump the content of the dying and unconfirmed lists, will help in case to debug suspected nf_conn object leaks. Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Jozsef Kadlecsik 提交于
The max number of sets was hardcoded at kernel cofiguration time and could only be modified via a module parameter. The patch adds the support of increasing the max number of sets automatically, as needed. The array of sets is incremented by 64 new slots if we run out of empty slots. The absolute limit for the maximal number of sets is limited by 65534. Signed-off-by: NJozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
-
由 Willy Tarreau 提交于
TCP coalescing added a regression in splice(socket->pipe) performance, for some workloads because of the way tcp_read_sock() is implemented. The reason for this is the break when (offset + 1 != skb->len). As we released the socket lock, this condition is possible if TCP stack added a fragment to the skb, which can happen with TCP coalescing. So let's go back to the beginning of the loop when this happens, to give a chance to splice more frags per system call. Doing so fixes the issue and makes GRO 10% faster than LRO on CPU-bound splice() workloads instead of the opposite. Signed-off-by: NWilly Tarreau <w@1wt.eu> Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 12月, 2012 8 次提交
-
-
由 David Woodhouse 提交于
We don't need to schedule the wakeup tasklet on *every* unlock; only if we actually blocked the channel in the first place. Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>
-
由 Krzysztof Mazur 提交于
The br2684 does not check if used vcc is in connected state, causing potential Oops in pppoatm_send() when vcc->send() is called on not fully connected socket. Now br2684 can be assigned only on connected sockets; otherwise -EINVAL error is returned. Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 David Woodhouse 提交于
The br2684 code used module_put() during unassignment from vcc with hope that we have BKL. This assumption is no longer true. Now owner field in atmvcc is used to move this module_put() to vcc_destroy_socket(). Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>
-
由 David Woodhouse 提交于
Now that we can return zero from pppoatm_send() for reasons *other* than the queue being full, that means we can't depend on a subsequent call to pppoatm_pop() waking the queue, and we might leave it stalled indefinitely. Use the ->release_cb() callback to wake the queue after the sock is unlocked. Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>
-
由 David Woodhouse 提交于
Avoid submitting packets to a vcc which is being closed. Things go badly wrong when the ->pop method gets later called after everything's been torn down. Use the ATM socket lock for synchronisation with vcc_destroy_socket(), which clears the ATM_VF_READY bit under the same lock. Otherwise, we could end up submitting a packet to the device driver even after its ->ops->close method has been called. And it could call the vcc's ->pop method after the protocol has been shut down. Which leads to a panic. Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>
-
由 David Woodhouse 提交于
The immediate use case for this is that it will allow us to ensure that a pppoatm queue is woken after it has to drop a packet due to the sock being locked. Note that 'release_cb' is called when the socket is *unlocked*. This is not to be confused with vcc_release() — which probably ought to be called vcc_close(). Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Acked-by: NKrzysztof Mazur <krzysiek@podlesie.net>
-
由 Shmulik Ladkani 提交于
As of 026359bc [ipv6: Send ICMPv6 RSes only when RAs are accepted], the logic determining whether to send Router Solicitations is identical to the logic determining whether kernel accepts Router Advertisements. However the condition itself is repeated in several code locations. Unify it by introducing 'ipv6_accept_ra()' accessor. Also, simplify the condition expression, making it more readable. No semantic change. Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
As time passed, available memory increased faster than number of concurrent tcp sockets. As a result, a machine with 4GB of ram gets a hash table with 524288 slots, using 8388608 bytes of memory. Lets change that by a 16x factor (one slot for 128 KB of ram) Even if a small machine needs a _lot_ of sockets, tcp lookups are now very efficient, using one cache line per socket. Signed-off-by: NEric Dumazet <edumazet@google.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 12月, 2012 8 次提交
-
-
由 Eric Dumazet 提交于
commit 68835aba (net: optimize INET input path further) moved some fields used for tcp/udp sockets lookup in the first cache line of struct sock_common. This patch moves inet_dport/inet_num as well, filling a 32bit hole on 64 bit arches and reducing number of cache line misses in lookups. Also change INET_MATCH()/INET_TW_MATCH() to perform the ports match before addresses match, as this check is more discriminant. Remove the hash check from MATCH() macros because we dont need to re validate the hash value after taking a refcount on socket, and use likely/unlikely compiler hints, as the sk_hash/hash check makes the following conditional tests 100% predicted by cpu. Introduce skc_addrpair/skc_portpair pair values to better document the alignment requirements of the port/addr pairs used in the various MATCH() macros, and remove some casts. The namespace check can also be done at last. This slightly improves TCP/UDP lookup times. IP/TCP early demux needs inet->rx_dst_ifindex and TCP needs inet->min_ttl, lets group them together in same cache line. With help from Ben Hutchings & Joe Perches. Idea of this patch came after Ling Ma proposal to move skc_hash to the beginning of struct sock_common, and should allow him to submit a final version of his patch. My tests show an improvement doing so. Signed-off-by: NEric Dumazet <edumazet@google.com> Cc: Ben Hutchings <bhutchings@solarflare.com> Cc: Joe Perches <joe@perches.com> Cc: Ling Ma <ling.ma.program@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Thomas Graf 提交于
If the variable parameter length provided in the mandatory heartbeat information parameter exceeds the calculated payload length the packet has been corrupted. Reply with a parameter length protocol violation message. Signed-off-by: NThomas Graf <tgraf@suug.ch> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rami Rosen 提交于
This patch removes an unused parameter (src_net) from rtnl_create_link() method and from the method single invocation, in veth. This parameter was used in the past when calling ops->get_tx_queues(src_net, tb) in rtnl_create_link(). The get_tx_queues() member of rtnl_link_ops was replaced by two methods, get_num_tx_queues() and get_num_rx_queues(), which do not get any parameter. This was done in commit d40156aa by Jiri Pirko ("rtnl: allow to specify different num for rx and tx queue count"). Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tommi Rantala 提交于
Trinity (the syscall fuzzer) triggered the following BUG, reproducible only when the kernel is configured with CONFIG_SCTP_DBG_MSG=y. When CONFIG_SCTP_DBG_MSG is not set, the null pointer is never dereferenced. ---[ end trace a4de0bfcb38a3642 ]--- BUG: unable to handle kernel NULL pointer dereference at 0000000000000100 IP: [<ffffffff8136796e>] ip6_string+0x1e/0xa0 PGD 4eead067 PUD 4e472067 PMD 0 Oops: 0000 [#1] PREEMPT SMP Modules linked in: CPU 3 Pid: 21324, comm: trinity-child11 Tainted: G W 3.7.0-rc7+ #61 ASUSTeK Computer INC. EB1012/EB1012 RIP: 0010:[<ffffffff8136796e>] [<ffffffff8136796e>] ip6_string+0x1e/0xa0 RSP: 0018:ffff88004e4637a0 EFLAGS: 00010046 RAX: ffff88004e4637da RBX: ffff88004e4637da RCX: 0000000000000000 RDX: ffffffff8246e92a RSI: 0000000000000100 RDI: ffff88004e4637da RBP: ffff88004e4637a8 R08: 000000000000ffff R09: 000000000000ffff R10: 0000000000000000 R11: 0000000000000000 R12: ffffffff8289d600 R13: ffffffff8289d230 R14: ffffffff8246e928 R15: ffffffff8289d600 FS: 00007fed95153700(0000) GS:ffff88005fd80000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000100 CR3: 000000004eeac000 CR4: 00000000000007e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process trinity-child11 (pid: 21324, threadinfo ffff88004e462000, task ffff8800524b0000) Stack: ffff88004e4637da ffff88004e463828 ffffffff81368eee 000000004e4637d8 ffffffff0000ffff ffff88000000ffff 0000000000000000 000000004e4637f8 ffffffff826285d8 ffff88004e4637f8 0000000000000000 ffff8800524b06b0 Call Trace: [<ffffffff81368eee>] ip6_addr_string.isra.11+0x3e/0xa0 [<ffffffff81369183>] pointer.isra.12+0x233/0x2d0 [<ffffffff810a413a>] ? vprintk_emit+0x1ba/0x450 [<ffffffff8110953d>] ? trace_hardirqs_on_caller+0x10d/0x1a0 [<ffffffff81369757>] vsnprintf+0x187/0x5d0 [<ffffffff81369c62>] vscnprintf+0x12/0x30 [<ffffffff810a4028>] vprintk_emit+0xa8/0x450 [<ffffffff81e5cb00>] printk+0x49/0x4b [<ffffffff81d17221>] sctp_v6_get_dst+0x731/0x780 [<ffffffff81d16e15>] ? sctp_v6_get_dst+0x325/0x780 [<ffffffff81d00a96>] sctp_transport_route+0x46/0x120 [<ffffffff81cff0f1>] sctp_assoc_add_peer+0x161/0x350 [<ffffffff81d0fd8d>] sctp_sendmsg+0x6cd/0xcb0 [<ffffffff81b55bf0>] ? inet_create+0x670/0x670 [<ffffffff81b55cfb>] inet_sendmsg+0x10b/0x220 [<ffffffff81b55bf0>] ? inet_create+0x670/0x670 [<ffffffff81a72a64>] ? sock_update_classid+0xa4/0x2b0 [<ffffffff81a72ab0>] ? sock_update_classid+0xf0/0x2b0 [<ffffffff81a6ac1c>] sock_sendmsg+0xdc/0xf0 [<ffffffff8118e9e5>] ? might_fault+0x85/0x90 [<ffffffff8118e99c>] ? might_fault+0x3c/0x90 [<ffffffff81a6e12a>] sys_sendto+0xfa/0x130 [<ffffffff810a9887>] ? do_setitimer+0x197/0x380 [<ffffffff81e960d5>] ? sysret_check+0x22/0x5d [<ffffffff81e960a9>] system_call_fastpath+0x16/0x1b Code: 01 eb 89 66 2e 0f 1f 84 00 00 00 00 00 55 48 89 f8 31 c9 48 89 e5 53 eb 12 0f 1f 40 00 48 83 c1 01 48 83 c0 04 48 83 f9 08 74 70 <0f> b6 3c 4e 89 fb 83 e7 0f c0 eb 04 41 89 d8 41 83 e0 0f 0f b6 RIP [<ffffffff8136796e>] ip6_string+0x1e/0xa0 RSP <ffff88004e4637a0> CR2: 0000000000000100 ---[ end trace a4de0bfcb38a3643 ]--- Signed-off-by: NTommi Rantala <tt.rantala@gmail.com> Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alan Ott 提交于
kfree_skb() indicates failure, which is where this is being used. Signed-off-by: NAlan Ott <alan@signal11.us> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alan Ott 提交于
kfree_skb() was not getting called in the case of some failures. This was pointed out by Eric Dumazet. Signed-off-by: NAlan Ott <alan@signal11.us> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alan Ott 提交于
Change the threshold for framentation of a lowpan packet from using the MTU size to now use the MTU size minus the checksum length, which is added by the hardware. For IEEE 802.15.4, this effectively changes it from 127 bytes to 125 bytes. Signed-off-by: NAlan Ott <alan@signal11.us> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yi Zou 提交于
This bug is observed on running FCoE over a VLAN device associated w/ a real device that has IFF_UNICAST_FLT set since FCoE would add unicast address such as FLOGI MAC to the VLAN interface that FCoE is on. Since currently, VLAN device is not inheriting the IFF_UNICAST_FLT flag from the parent real device even though the real device is capable of doing unicast filtering. This forces the VLAN device and its real device go to promiscuous mode unnecessarily even the added address is actually being added to the available unicast filter table in real device. Signed-off-by: NYi Zou <yi.zou@intel.com> Cc: devel@open-fcoe.org Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 11月, 2012 4 次提交
-
-
由 Krzysztof Mazur 提交于
The pppoatm_may_send() is quite heavy and it's called three times in pppoatm_send() and inlining costs more than 200 bytes of code (more than 10% of total pppoatm driver code size). add/remove: 1/0 grow/shrink: 0/1 up/down: 132/-367 (-235) function old new delta pppoatm_may_send - 132 +132 pppoatm_send 900 533 -367 Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Krzysztof Mazur 提交于
The vcc_destroy_socket() closes vcc before the protocol is detached from vcc by calling vcc->push() with NULL skb. This leaves some time window, where the protocol may call vcc->send() on closed vcc and crash. Now pppoatm_send(), like vcc_sendmsg(), checks for vcc flags that indicate that vcc is not ready. If the vcc is not ready we just drop frame. Queueing frames is much more complicated because we don't have callbacks that inform us about vcc flags changes. Signed-off-by: NKrzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
-
由 Antonio Quartulli 提交于
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead of the private BATADV_ETH_P_BATMAN define. Signed-off-by: NAntonio Quartulli <ordex@autistici.org> Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
-
由 Rami Rosen 提交于
This patch changes three methods to be static and removes their EXPORT_SYMBOLs in core/dev.c and their external declaration in netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and napi_skb_finish(), which are in the GRO rx path, are not used outside core/dev.c. Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 11月, 2012 7 次提交
-
-
由 Jesse Gross 提交于
Currently, each time a device is detached from an OVS datapath we call synchronize RCU before freeing associated data structures. However, if a bridge is deleted (which detaches all ports) when many devices are connected then there can be a long delay. This switches to use call_rcu() to group the cost together. Reported-by: NJustin Pettit <jpettit@nicira.com> Signed-off-by: NJesse Gross <jesse@nicira.com>
-
由 Nicolas Dichtel 提交于
This patch reports the change made by Stephen Hemminger in ipip and gre[6] in commit eccc1bb8 (tunnel: drop packet if ECN present with not-ECT). Goal is to handle RFC6040, Section 4.2: Default Tunnel Egress Behaviour. o If the inner ECN field is Not-ECT, the decapsulator MUST NOT propagate any other ECN codepoint onwards. This is because the inner Not-ECT marking is set by transports that rely on dropped packets as an indication of congestion and would not understand or respond to any other ECN codepoint [RFC4774]. Specifically: * If the inner ECN field is Not-ECT and the outer ECN field is CE, the decapsulator MUST drop the packet. * If the inner ECN field is Not-ECT and the outer ECN field is Not-ECT, ECT(0), or ECT(1), the decapsulator MUST forward the outgoing packet with the ECN field cleared to Not-ECT. The patch takes benefits from common function added in net/inet_ecn.h. Like it was done for Xin4 tunnels, it adds logging to allow detecting broken systems that set ECN bits incorrectly when tunneling (or an intermediate router might be changing the header). Errors are also tracked via rx_frame_error. CC: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tommi Rantala 提交于
Cleanup the memory we allocated earlier in irttp_open_tsap() when we hit this error path. The leak goes back to at least 1da177e4 ("Linux-2.6.12-rc2"). Discovered with Trinity (the syscall fuzzer). Signed-off-by: NTommi Rantala <tt.rantala@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Paolo Valente 提交于
This patch turns QFQ into QFQ+, a variant of QFQ that provides the following two benefits: 1) QFQ+ is faster than QFQ, 2) differently from QFQ, QFQ+ correctly schedules also non-leaves classes in a hierarchical setting. A detailed description of QFQ+, plus a performance comparison with DRR and QFQ, can be found in [1]. [1] P. Valente, "Reducing the Execution Time of Fair-Queueing Schedulers" http://algo.ing.unimo.it/people/paolo/agg-sched/agg-sched.pdfSigned-off-by: NPaolo Valente <paolo.valente@unimore.it> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Schoch Christian 提交于
The calculation of RTTVAR involves the subtraction of two unsigned numbers which may causes rollover and results in very high values of RTTVAR when RTT > SRTT. With this patch it is possible to set RTOmin = 1 to get the minimum of RTO at 4 times the clock granularity. Change Notes: v2) *Replaced abs() by abs64() and long by __s64, changed patch description. Signed-off-by: NChristian Schoch <e0326715@student.tuwien.ac.at> CC: Vlad Yasevich <vyasevich@gmail.com> CC: Sridhar Samudrala <sri@us.ibm.com> CC: Neil Horman <nhorman@tuxdriver.com> CC: linux-sctp@vger.kernel.org Acked-by: NVlad Yasevich <vyasevich@gmail.com> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tommi Rantala 提交于
Consider the following program, that sets the second argument to the sendto() syscall incorrectly: #include <string.h> #include <arpa/inet.h> #include <sys/socket.h> int main(void) { int fd; struct sockaddr_in sa; fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/); if (fd < 0) return 1; memset(&sa, 0, sizeof(sa)); sa.sin_family = AF_INET; sa.sin_addr.s_addr = inet_addr("127.0.0.1"); sa.sin_port = htons(11111); sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa)); return 0; } We get -ENOMEM: $ strace -e sendto ./demo sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 ENOMEM (Cannot allocate memory) Propagate the error code from sctp_user_addto_chunk(), so that we will tell user space what actually went wrong: $ strace -e sendto ./demo sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 EFAULT (Bad address) Noticed while running Trinity (the syscall fuzzer). Signed-off-by: NTommi Rantala <tt.rantala@gmail.com> Acked-by: NVlad Yasevich <vyasevich@gmail.com> Acked-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tommi Rantala 提交于
Trinity (the syscall fuzzer) discovered a memory leak in SCTP, reproducible e.g. with the sendto() syscall by passing invalid user space pointer in the second argument: #include <string.h> #include <arpa/inet.h> #include <sys/socket.h> int main(void) { int fd; struct sockaddr_in sa; fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/); if (fd < 0) return 1; memset(&sa, 0, sizeof(sa)); sa.sin_family = AF_INET; sa.sin_addr.s_addr = inet_addr("127.0.0.1"); sa.sin_port = htons(11111); sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa)); return 0; } As far as I can tell, the leak has been around since ~2003. Signed-off-by: NTommi Rantala <tt.rantala@gmail.com> Acked-by: NVlad Yasevich <vyasevich@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-