Add support for DRA7xx to the HDMI driver.

The HDMI block on DRA7xx is the same as on OMAP5, except we need to
enable and disable the HDMI PLL via the CONTROL module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

On DRA7xx, DISPC needs to write output signal polarities not only to a
DISPC register, like for all earlier DSS versions, but to control
module's CTRL_CORE_SMA_SW_1 register.

This patch adds support to write the polarities to control module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add DRA7xx support to DISPC driver. The DISPC block is the same as on
OMAP5, except the PLL's used for clocking are "videoX", not "dsiX".
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DRA7xx SoCs have one (DRA72x) or two (DRA74x) video PLLs. They are
basically the same as DSI PLLs on OMAPs, but without the rest of the DSI
hardware. The video PLLs also require some configuration via the CONTROL
module.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add functions which configure the control module register
CTRL_CORE_DSS_PLL_CONTROL found in DRA7xx SoCs. This register configures
whether the PLL registers are accessed internally by DSS, or externally
using OCP2SCP interface. They also configure muxes which route the PLL
output to a particular LCD overlay manager within DSS.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add base support for DRA7xx to DSS core.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The OMAP5 HW supports directing DIGIT channel to DPI output, but the
driver doesn't support that. However, we have marked that configuration
as possible in the dss features, so in certain cases the driver tries to
use that configuration, leading to broken display.

Fix the problem by allowing DIGIT channel to go only to HDMI output.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The port arrays are constant data, so set them as 'const'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add a helper function to wait until the PLL's reset is done.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

In some cases we need global identifiers for the DSS PLLs, for example
when configuring clock muxing on DRA7. For this purpose let's add a
'enum dss_pll_id'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

After the commit ef691ff4 (OMAPDSS: DT: Get source endpoint by
matching reg-id) we look for the SDI output using the port number.
However, the SDI driver doesn't set the port number, which causes the
SDI display to not initialize.

Fix this by setting the SDI port number to 1. We use a hardcoded value,
as SDI was used only on OMAP3 and it's always port number 1 there.
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The regulator_disable() doesn't accept NULL pointers.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI hardware parameters structs for OMAP4 and OMAP5 contained two
initializers for 'clkdco_max'. The first one was a remnant with wrong
value.

Remove the extra initializer entries.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The bit field for IEC958_AES2_CON_SOURCE is bits 3-0 in
HDMI_CORE_FC_AUDSCHNLS2, not imaginary bits 3-4 (reverse order).
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Remove __exit qualifier from hdmi_uninit_output() because it is used
also in omapdss_hdmihw_probe().
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Enabling idle mode during audio playback causes the glitches on OMAP5
HDMI. The TRM also suggests to use no-idle for HDMI audio playback.

This patch sets HDMI idle mode to no-idle for the duration of the
playback, and restores it back to original value afterwards.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Removes the OMAP5 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Implements callbacks for OMAP HDMI audio platform driver and registers
it in probe function. Unregistering is done in remove function.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Removes the OMAP4 HDMI audio callbacks for the old external DAI driver.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Make hdmi_mode_has_audio() more user friedly by taking hdmi_config as
parameter.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The booleans are not used anymore. Just select SND_OMAP_SOC_HDMI_AUDIO
to enable OMAP HDMI audio support.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Reviewed-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Adds display_enabled flag and audio_abort_cb callback to struct hdmi.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

This is used to store omap-hdmi-audio pdev for unregistering it.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Unify the private anonymous struct in hdmi4.c and hdmi5.c, name it as
struct omap_hdmi, and make it public in hdmi.h.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The audio dma port is found in the hdmi_wp physical address space.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

hdmi4_audio_get_dma_port() is unused and and broken.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

It does not waste too many bytes to compile all audio related core
functions always in with HDMI support. It should help readability and
in keeping the audio code in working shape. Leave the options just for
disabling and enabling the functionality in hdmi[45].c.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The OMAP5 HDMI audio implementation needs HDMI_AUDIO_LAYOUT_6CH in
hdmi_core_audio_layout enum. I found the correct value from ti-linux
3.8 tree.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The hdmi_wp_audio_config_format() expects sample_order of struct
hdmi_audio_format to be initialized. The only allowed value is
HDMI_AUDIO_SAMPLE_LEFT_FIRST.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Only OMAP4 DSS has non reserved bits above 6th bit in HDMI_WP_AUDIO_CFG.
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that the DSS has the common DSS PLL, we no longer use the DSI PLL
feature flags from dss_features.c.

Remove all the unused feature flags.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Now that we have the common DSS PLL support, change HDMI to use it. This
results in quite a lot of changes, but almost all of them are trivial
name changes.

The function to program the PLL settings can be removed from hdmi_pll.c,
as the common PLL API contains the same functionality.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

hdmi_pll_enable powers off the PLL as the first thing it does. Right
after that, it enables the PLL powers.

The initial power-off is pointless, so let's remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

At the moment we have one function, hdmi_pll_enable, which enables the
PLL and writes the PLL configuration to registers.

To make the HDMI PLL ahere to the DSS PLL API, split the hdmi_pll_enable
into two parts: hdmi_pll_enable which enables the PLL HW, and
hdmi_pll_set_config which writes the config.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI PLL code needs the pointer to the WP block so that it can manage
its power. Currently this is passed as a function parameter to
hdmi_pll_enable and hdmi_pll_disable. To make the PLL function adhere to
the DSS PLL API, we need to remove the WP parameter.

This patch stores the WP pointer to hdmi_pll_data in hdmi_pll_init, so
that it's available when needed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The SYSRESET bits in HDMI PLL do not reset the PLL itself, but only
affect the power used for the PLL.

Afaik there is no reason to use the SYSRESET bits, and we don't use it
in the other PLLs, so let's remove the HDMI PLL reset to make the PLL
code simpler and similar to other PLLs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The code calculating HDMI PLL parameters has always been very confusing.
Now that we are implementing a common PLL library for the DSS, it's
important that the PLL code is understandable.

This patch rewrites the calculation code, and removes a few hacks that
were used there.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

We don't support interlace modes properly on OMAP5+ HDMI, so we need to
reject interlace timings.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Only OMAP5+ has REFSEL field, but at the moment it's set also on OMAP4.

Fix this by adding a "has_refsel" field, and setting the REFSEL based on
that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>