These local symbols are used only in this file.
Fix the following sparse warnings:

drivers/tty/serial/sirfsoc_uart.c:147:6: warning: symbol 'sirfsoc_uart_start_tx' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.c:636:5: warning: symbol 'sirfsoc_uart_probe' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Universal Serial Ports (USP) can be used as PCM, UART, SPI,
I2S etc. this makes the USP work as UART. the basic work
flow is same with UART controller, the main difference will
be offset of registers and bits.

this patch makes the old sirfsoc uart driver support both
sirf UART and USP-based UART by making their differences
become private data.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

the marco and coming new CSR multiple SoCs have SET/CLR pair for
INTEN registers to avoid some read-modify-write.

this patch adds support for this and make the driver support current
up and coming mp SoCs.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

devicetrees may have the linux,stdout-path property to specify the
console. This patch adds support to the i.MX serial driver for this.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use devm_* functions in order to simplify cleanup
paths.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These local symbols are used only in this file.
Fix the following sparse warnings:

drivers/tty/serial/pxa.c:793:17: warning: symbol 'serial_pxa_pops' was not declared. Should it be static?
drivers/tty/serial/pxa.c:971:12: warning: symbol 'serial_pxa_init' was not declared. Should it be static?
drivers/tty/serial/pxa.c:986:13: warning: symbol 'serial_pxa_exit' was not declared. Should it be static?
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This #if-0'd block wouldn't compile, so let's dispose it.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MXS_AUART_DMA_CONFIG is originally used to check if the DT node
is configured with the DMA property.

But now, the MXS_AUART_DMA_CONFIG is set unconditionally in the
serial_mxs_probe_dt(), so the check in the mxs_auart_settermios() is
not necessary anymore. This patch removes this macro.
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The original DMA support works only when RTS/CTS is enabled.
(see the "e8001632 serial: mxs-auart: add the DMA support for mx28")
But after several patches, DMA support has lost this limit.
(see the "bcc20f9e serial: mxs-auart: move to use generic DMA helper")

So an UART without the RTS/CTS lines may also enables the DMA support,
in which case the UART may gets unpredictable results.

This patch adds an optional property for the UART DT node
which indicates the UART has RTS and CTS lines, and it also means you
enable the DMA support for this UART.

This patch also adds a macro MXS_AUART_RTSCTS, and uses it to check
RTS/CTS before we enable the DMA for the UART.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NHuang Shijie <shijie8@gmail.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes a below warning reported by kbuild test robot.

drivers/tty/serial/st-asc.c:727:28: warning: 'asc_match' defined but
 not used [-Wunused-variable]

The code used in DT case is now ifdefed under CONFIG_OF to fix this
warning.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Reported-by: NKbuild Test Robot <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 85c99690.

Alexander wishes to remove this patch as it is incorrect.
Reported-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently, Rx error handling only triggers if there is some Rx data.
Fix that by checking for error - before the data handling.
Reported-by: NMischa Jonker <mjonker@synopsys.com>
Tested-by: NMischa Jonker <mjonker@synopsys.com>
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DT support to the SCCNCP serial driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch replaces switch in probe function to constant structure
for each supported IC. This makes code a bit smaller and cleaner and
helps adding DT support to the driver in the future.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch removes "frequency" parameter from SCCNXP platform_data
and uses CLK API for getting clock. If CLK ommited, default IC
frequency will be used instead.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch disables the regulator in case of errors, if we have it.
In addition, the patch adds support for deferred regulator probe and
makes error path are a bit clean.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

pdev->id is not a valid choice for device-tree probed devices. So use
the (properly determined) line from efm32_uart_probe consistenly
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We can't use dev->mod_index for selecting the interrupt routing entry,
because it's not an index into interrupt routing table. It will be even
wrong on a machine with 2 CPUs (4 cores). But all needed information is
contained in the PAT entries for the serial ports. mod[0] contains the
iosapic address and mod_info has some indications for the interrupt
input (at least it looks like it). This patch implements the searching
for the right iosapic and uses this interrupt input information.
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: <stable@vger.kernel.org> # 3.10
Signed-off-by: NHelge Deller <deller@gmx.de>

Storing one struct per known board would be overkill. Pre-cast the
driver_data pointer to an unsigned long to avoid the pointer to int
compiler warning:

drivers/tty/serial/pch_uart.c:431:10: warning: cast from pointer to
integer of different size [-Wpointer-to-int-cast]

Unify the signed-ness of the baud and uartclk types throughout the
driver.
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Because the UART lack of receive timeout register, so we use a timer to trigger
data receive.
The DBGU is regarded as UART.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Distinguish usart and uart by read ip name register,
The usart read name is "USAR",
The uart and dbgu read name is "DBGU".
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We will switch to pio mode when request of dma or pdc fail.
But soon or later, when the request is success, the transfer mode can switch to them at
next open serial port action.
So in startup stage, we should get original transfer mode.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Request a cyclic dma channel for rx dma use. Use cyclic transfer is to prevent
receive data overrun.

We allocate a cycle dma cookie after request channel,
after that, enable uart timeout interrupt in startup stage, when data successful
received, the timeout callback will check the residual bytes and insert
receiving datas into the framework during the transfer interval.

When current descriptor finished, the dma callback will also check the residual
bytes and filp the receiving data.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Request a slave dma channel for tx dma use. Tx dma will setup a single transfer,
when transfer complete, it will call atmel_complete_tx_dma to do finish stuff.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

use function pointer can avoid define atmel_use_pdc_tx/rx everywhere.
(*prepare_rx/tx)() is in setup transfer stage.
(*schedule_rx/tx)() is in tasklet schedule stage.
(*release_rx/tx)() is used when shutdown the transfer.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The DMA is available since at91sam9x5 socs, before that, we use PDC.
Signed-off-by: NElen Song <elen.song@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The dmi_table is best accessed from the probe function, which is not
an __init function. Drop the __initdata annotation from the dmi_table
to avoid the section mismatch compiler warnings:

WARNING: drivers/tty/serial/pch_uart.o(.text+0x4871): Section mismatch
in reference from the function pch_uart_init_port() to the variable
.init.data:pch_uart_dmi_table
Signed-off-by: NDarren Hart <dvhart@linux.intel.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes wrong dev_pm_ops which caused by commit:
serial: max310x: Driver rework.

  CC      drivers/tty/serial/max310x.o
  LD      drivers/video/fb.o
  CC      drivers/w1/slaves/w1_ds2433.o
  CC      drivers/w1/slaves/w1_ds2760.o
  CC      drivers/xen/balloon.o
  CC      drivers/video/backlight/adp8870_bl.o
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.suspend') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.resume') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.freeze') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.thaw') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.poweroff') [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/tty/serial/max310x.c:1292:8: warning: (near initialization for 'max310x_pm_ops.restore') [enabled by default]
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Platform drivers use "platform:" prefix in module alias.
Also use DRIVER_NAME in MODULE_ALIAS to make module autoloading work.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NVineet Gupta <vgupta@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without this patch the driver waits ~1 ms for the UART to become idle. At
115200n8 this time is (theoretically) enough to transfer 11.5 characters
(= 115200 bits/s / (10 Bits/char) * 1ms). As the mxs-auart has a fifo size
of 16 characters the clock is gated too early. The problem is worse for
lower baud rates.

This only happens to really shut down the transmitter in the middle of a
transfer if /dev/ttyAPPx isn't opened in userspace (e.g. by a getty) but
was at least once (because the bootloader doesn't disable the transmitter).

So increase the timeout to 20 ms which should be enough for 9600n8, too.
Moreover skip gating the clock if the timeout is elapsed.

Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The handler needs to ack the pending events before actually handling them.
Otherwise a new event might come in after it it considered non-pending or
handled and is acked then without being handled. So this event is only
noticed when the next interrupt happens.

Without this patch an i.MX28 based machine running an rt-patched kernel
regularly hangs during boot.

Cc: stable@vger.kernel.org # v2.6.39+
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace kzalloc and clk_get by their managed counterparts to simplify
error and cleanup paths.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTDM cores have a TX fifo that can accept more than one
character per register write, but the msm_serial driver currently
only supports 1 character mode. Add support for this mode of operation
to speed up the transmit path on DM devices.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently msm_set_baud_rate() assumes the uart clock rate is
1.8432 MHz. This is not always true, and limits our options to
program the baud rate. Instead of assuming the rate and
hard-coding the baud_code based on it, calculate the divider that
we want and try to find the closest baud_code that matches. This
allows us to support uarts with faster clock speeds.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/msm_serial.c:302:6: warning: symbol 'msm_set_mctrl' was
not declared. Should it be static?
drivers/tty/serial/msm_serial.c:597:17: warning: incorrect type in argument 2
(different address spaces)
drivers/tty/serial/msm_serial.c:597:17: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:597:17: got unsigned int *
drivers/tty/serial/msm_serial.c:608:33: warning: incorrect type in argument 1
(different address spaces)
drivers/tty/serial/msm_serial.c:608:33: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:608:33: got unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: warning: incorrect type in assignment
(different address spaces)
drivers/tty/serial/msm_serial.c:648:37: expected unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: got void [noderef] <asn:2>*

Mark the ioremapped memory as __iomem and use writel instead of
iowrite because we're not dealing with PCI devices. Also, mark
msm_set_mctrl() static because it isn't used outside this file.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UARTDM serial devices require us to wait for the entire TX fifo
to drain before we can change the contents of the NCF_TX
register. Furthermore, if we write any characters to the TX fifo
within the same clock cycle of changing the NCF_TX register the
NCF_TX register won't latch properly.

To fix these issues we should read back the NCF_TX register to
delay any TX fifo accesses by a clock cycle and we should wait
for the TX fifo to drain (instead of just waiting for the fifo to
be ready to receive more characters). Failure to do so leads to
random NUL bytes interspersed in the output.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>