Passing the port as a parameter to PANEL_PORT_SELECT_VLV results in
neater code. Sadly the PCH port select bits aren't suitable for the
same treatment and the resulting macro would be much uglier, so
leave those defines as is.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Chris has decided that enough is enough. It's time to fixup dev Vs
dev_priv. This is a modest contribution to the crusade.

v2: Still use INTEL_INFO(), for the (mythical!) case we want to hardcode
    the info struct with defines (Chris)
    Rename the macro argument from 'dev' to 'dev_priv' (Jani)

v3: Use names unlikely to be used as macro arguments (Chris)
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This lets the userspace switch off the backlight using the backlight
class sysfs bl_power file. The switch is done using the power sequencer;
the backlight PWM, and everything else, remains enabled. The display
backlight won't draw power, but for maximum power savings the encoder
needs to be switched off.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make it possible to change panel power control backlight state without
touching the PWM. No functional changes.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm we may retrain the DP link even if the CRTC is inactive through
HPD work->intel_dp_check_link_status(). This in turn can lock up the PHY
(at least on BYT), since the DP port is disabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81948Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.

Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.

v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
  edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
  (Imre)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Ville noticed that we can call ibx_digital_port_connected() which accesses
the HW without holding any power well/runtime pm reference. Fix this by
holding a display port power domain reference around the whole hpd_pulse
handler.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Don't print raw numbers, use port_name() and tell the user whether it's
long or short without having to figure out what the other magic number
means.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While those messages are interesting, there aren't _that_ interesting.
We don't need them in the kernel logs by default.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV display PHY registes have two swing margin/deemph settings. Make it
clear which ones we're using.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV was forgotten the intel_{dp,hdmi}_prepare() were introduced (or the
chv patches were still in flight?). Call these when enabling the ports.

Things tend to work much better when we actually write something
to the port registers :)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Future platform will use config->ddi_pll_sel in a different way.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV supports DP training pattern 3. Add the required stuff.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

For Gen < 8, set M2_N2 registers on every mode set. This is required to make
sure M2_N2 registers are set during boot, resume from sleep for cross-
checking the state. The register is set only if DRRS is supported.

v2: Patch rebased

v3: Daniel's review comments
	- Removed HAS_DRRS(dev) and added bool has_drrs to pipe_config to
	track drrs support

v4: Jesse's review comments
	- Made changes to set m2_n2 in intel_dp_set_m_n()
Signed-off-by: NVandana Kannan <vandana.kannan@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since I've reworked psr support to no longer require x-tiling we don't
check any state protected by the Giant GEM Lock. So drop that check.

Also boo for lockdep_assert_held for not yelling when lockdep is
disabled.

Cc: Paulo Zanoni <przanoni@gmail.com>
Reported-by: NPaulo Zanoni <przanoni@gmail.com>
Acked-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Just like during booting the BIOS can leave the VDD bit enabled after
system resume. So apply the same state sanitization there too. This
fixes a problem where after resume the port power domain refcount gets
unbalanced.

v2:
- unchanged
v3:
- call edp sanitizing from the encoder reset handler (Daniel)
Reported-and-tested-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will be needed by an upcoming patch too that needs to sanitize the
VDD state during resume. The additional async disabling is only needed
for the resume path, here it doesn't make a difference since we enable
VDD right after the sanitize call.

v2:
- don't set intel_dp ptr for non-eDP encoders (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to take the connection mutex around the link status
check for non-MST case, but also around the MST link training
on short HPDs.

I suspect we actually should have a dpcd lock in the future as
well, that just lock the local copies of dpcd and flags stored
from that.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We already call intel_display_power_get, which will get a power
domain, and every power domain should get a runtime PM reference,
which will wake up the machine.

v2: - Also touch intel_crt_detect() (Ville).
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Fixup commit message as spotted by Ville.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We only need to check for this in psr_enable, everything else is
already protect by the dev_priv->psr.enabled checks. Those need the
psr locking, but these functions are called infrequent enough that the
locking overhead is negligible.

Suggested by Chris Wilson.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.

- Use frontbuffer tracking bits stuff to separate disable and
  re-enable.

- Don't re-check everything in the psr work. We have now accurate
  tracking for everything, so no need to check for sprites or tiling
  really. Allows us to ditch tons of locks.

- That in turn allows us to properly cancel the work in the disable
  function - no more deadlocks.

- Add a check for HSW sprites and force a flush. Apparently the
  hardware doesn't forward the flushing when updating the sprite base
  address. We can do the same trick everywhere else we have such
  issues, e.g. on baytrail with ... everything.

- Don't re-enable psr with a delay in psr_exit. It really must be
  turned off forever if we detect a gtt write. At least with the
  current frontbuffer render tracking. Userspace can do a busy ioctl
  call or no-op pageflip to re-enable psr.

- Drop redundant checks for crtc and crtc->active - now that they're
  only called from enable this is guaranteed.

- Fix up the hsw port check. eDP can also happen on port D, but the
  issue is exactly that it doesn't work there. So an || check is
  wrong.

- We still schedule the psr work with a delay. The frontbuffer
  flushing interface mandates that we upload the next full frame, so
  need to wait a bit. Once we have single-shot frame uploads we can do
  better here.

v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.

v3: s/psr_exit/psr_invalidate/ for consistency

v4: Fixup whitespace.

v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.

v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
  by Rodrigo.
- Comments Chris requested to clarify the code.

v7: Fix conflict on rebase (Rodrigo)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not really optional to have locking ...

The ugly part is how much locking the psr work needs since it has to
recheck everything. Which is way too much. But we need to ditch the
psr work in it's current form anyway and implement proper frontbuffer
tracking.

The other nasty bit that had to go was the delayed work cancle in
psr_exit. Which means a bunch of races just became a bit more likely,
but mea culpa.

v2: Fixup HAS_PSR checks, resulting in uninitialized mutex issues.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to make sure that no one else is using this in the
enable function and also that the work item hasn't raced
with the disabled function.

v2: Improve bisectability by moving one hunk to an earlier patch.

v3: added missing dev_priv declaration (Rodrigo)
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make sure we track the sw side (psr.active) correctly and WARN
everywhere it might get out of sync with the hw.

v2: Fixup WARN_ON logic inversion, reported by Rodrigo.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's disabled already except when we've raced.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Trying to fish that one out through looping is a bit a locking
nightmare. So just set it and use it in the work struct.

v2:
- Don't Oops in psr_work, spotted by Rodrigo.
- Fix compile warning.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Can't review this right now due to lack of DRRS code.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Due to runtime pm and system s/r we need to restore hw state every
time we enable a pipe again. Hence trying to avoid that is just
pointless book-keeping which Rodrigo then tried to work around by
manually adding psr_setup calls to our resume code.

Much simpler to just remove code instead.

v2: Properly bail out of psr exit if psr isn't enabled. Spotted by
Rodrigo.
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This adds DP 1.2 MST support on Haswell systems.

Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.

Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders

Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.

Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.

Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume

Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act

Changes since v0.6:
cleanup unused struct entry.

[airlied: fix some sparse warnings].
Reviewed-by: NTodd Previte <tprevite@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Not enough brown paper bags, you'll have to share one.
(oops below).

The initial match condition code was racy (locking is coming I hear).

then along came:
cd234b0b
drm/i915: Do not dereference NULL crtc or fb until after checking

Chris made an attempt to fix it, Ben "reviewed" it.
Daniel merged it.

Then
drm/i915: Make use of intel_fb_obj() (v2)
2ff8fde1

made it worse by removing the obj check later.

All in all, my laptop can't barely turn off the display
without hitting this.

Posted to #intel-gfx out of niceness, but I've merged
this already into drm-next.

Here's an oops.
[   11.528185] BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0
[   11.528233] IP: [<ffffffffa0161fde>] intel_edp_psr_match_conditions+0x1e/0x2e0 [i915]
[   11.528294] PGD 35bc0067 PUD c997c067 PMD 0
[   11.528321] Oops: 0000 [#1] SMP
[   11.528916] CPU: 3 PID: 244 Comm: kworker/3:2 Not tainted 3.16.0-rc4+ #17
[   11.528949] Hardware name: LENOVO 20ARS25701/20ARS25701, BIOS GJET72WW (2.22 ) 02/21/2014
[   11.529004] Workqueue: events intel_edp_psr_work [i915]
[   11.529031] task: ffff8803079fdaa0 ti: ffff8803079c4000 task.ti: ffff8803079c4000
[   11.529067] RIP: 0010:[<ffffffffa0161fde>]  [<ffffffffa0161fde>] intel_edp_psr_match_conditions+0x1e/0x2e0 [i915]
[   11.529129] RSP: 0018:ffff8803079c7d40  EFLAGS: 00010246
[   11.529155] RAX: 0000000000000000 RBX: ffff88030c11c000 RCX: c000000000000000
[   11.529189] RDX: 0000000000000001 RSI: 1df0000000000000 RDI: ffff88030c1190d8
[   11.529222] RBP: ffff8803079c7d60 R08: ffffffff82691140 R09: 0000000000000000
[   11.529256] R10: ffff8803079fdaa0 R11: 3e00000000000000 R12: ffff88030c11c728
[   11.529290] R13: ffff88030c1190d8 R14: ffff88031e2d8e00 R15: 00000000000000c0
[   11.529324] FS:  0000000000000000(0000) GS:ffff88031e2c0000(0000) knlGS:0000000000000000
[   11.529361] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   11.529389] CR2: 00000000000000d0 CR3: 00000000c8d9d000 CR4: 00000000001407e0
[   11.529423] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   11.529457] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   11.529489] Stack:
[   11.529500]  ffff88030c119000 ffff88030c11c728 ffff88030c1190d8 ffff88031e2d8e00
[   11.529541]  ffff8803079c7d88 ffffffffa01679b2 ffff880035b29a80 ffff880307909f00
[   11.529583]  ffff88031e2d4740 ffff8803079c7df8 ffffffff810a78ab ffffffff810a7849
[   11.529624] Call Trace:
[   11.529654]  [<ffffffffa01679b2>] intel_edp_psr_work+0x52/0x90 [i915]
[   11.529689]  [<ffffffff810a78ab>] process_one_work+0x1db/0x540
[   11.529719]  [<ffffffff810a7849>] ? process_one_work+0x179/0x540
[   11.529750]  [<ffffffff810a81ed>] worker_thread+0x11d/0x520
[   11.529779]  [<ffffffff810a80d0>] ? create_and_start_worker+0x60/0x60
[   11.529810]  [<ffffffff810aeb04>] kthread+0xe4/0x100
[   11.529836]  [<ffffffff810aea20>] ? kthread_create_on_node+0x200/0x200
[   11.529870]  [<ffffffff81705ebc>] ret_from_fork+0x7c/0xb0
[   11.529896]  [<ffffffff810aea20>] ? kthread_create_on_node+0x200/0x200
[   11.529926] Code: ba 31 13 f0 c9 85 f6 75 84 eb d0 66 90 0f 1f 44 00 00 55 48 89 e5 41 56 41 55 41 54 53 48 8b 87 68 ff ff ff 48 8b 9f 28 ff ff ff <48> 8b 80 d0 00 00 00 4c 8b 63 28 48 8b 40 48 48 85 c0 0f 84 1a
[   11.530110] RIP  [<ffffffffa0161fde>] intel_edp_psr_match_conditions+0x1e/0x2e0 [i915]
[   11.530163]  RSP <ffff8803079c7d40>
[   11.530180] CR2: 00000000000000d0
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 38aecea0.

This breaks Haswell Thinkpad + Lenovo dock in SST mode with a HDMI monitor attached.

Before this we can 1920x1200 mode, after this we only ever get 1024x768, and
a lot of deferring.

This didn't revert clean, but this should be fine.

bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1117008
Cc: stable@vger.kernel.org # v3.15
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This way only the dynamic WRPLL selection for hdmi ddi mode is
done in intel_ddi_pll_select.

v2: Don't clobber the precomputed values when selecting clocks fro
hdmi encoders.
v3 (from Paulo): Rebase on top of the s/IS_HASWELL/HAS_DDI/ patch.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Don't let it fall in the HAS_PCH_SPLIT() case.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.

Potential uses of this macro were identified via the following
Coccinelle patch:

        @@
        expression E;
        @@
        * to_intel_framebuffer(E)->obj

        @@
        expression E;
        identifier I;
        @@
          I = to_intel_framebuffer(E);
          ...
        * I->obj

v2: Rewrite some NULL tests in terms of the obj rather than the fb.
    Also add a WARN() if trying to pageflip with a disabled primary
    plane.  [Suggested by Chris Wilson]
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.

Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg

Ver3: moved SYS_RESTART check earlier, new name for pp_div.

Ver4: Minor issue changes

Ver5: Move registration of reboot notifier to edp_connector_init,
      Added warning comment to handler about lack of PM notification.
Signed-off-by: NClint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With the new checks in place, we can see we're doing things backwards,
so fix them up per the spec.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The digital ports from Ironlake and up have the ability to distinguish
between long and short HPD pulses. Displayport 1.1 only uses the short
form to request link retraining usually, so we haven't really needed
support for it until now.

However with DP 1.2 MST we need to handle the short irqs on their
own outside the modesetting locking the long hpd's involve. This
patch adds the framework to distinguish between short/long to the
current code base, to lay the basis for future DP 1.2 MST work.

This should mean we get better bisectability in case of regression
due to the new irq handling.

v2: add GM45 support (untested, due to lack of hw)
Signed-off-by: NDave Airlie <airlied@redhat.com>
Reviewed-by: NTodd Previte <tprevite@gmail.com>
[danvet: Fix conflicts in i915_irq.c with Oscar Mateo's irq handling
race fixes and a trivial one in intel_drv.h with the psr code.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It doesn't make sense to never again schedule the work, since by the
time we might want to re-enable psr the world might have changed and
we can do it again.

The only exception is when we shut down the pipe, but that's an
entirely different thing and needs to be handled in psr_disable.

Note that later patch will again split psr_exit into psr_invalidate
and psr_flush. But the split is different and this simplification
helps with the transition.

v2: Improve the commit message a bit.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have _enable/_disable interfaces now for the modeset sequence and
intel_edp_psr_exit for workarounds.

The callsites in intel_display.c are all redundant with the modeset
sequence enable/disable calls in intel_ddi.c. The one in
intel_sprite.c is real and needs to be switched to psr_exit.

If this breaks anything then we need to augment the enable/disable
functions accordingly.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It's not needed and further more will get in the way of a sane
locking scheme - psr_exit _can't_ take modeset locks due to lock
inversion, and at least once dp mst hits the connector list
is no longer static.

But since we track all state in dev_priv->psr there is no need
at all.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>