On CSR SiRFprimaII/atlasVI, there is a programmable 16-bit divider
(RTC_DIV) that divides the input 32.768KHz clock to the frequency that
users need (E.g.  1 Hz).  The divided real-time clock will be used to
drive a 32-bit counter (RTC_COUNTER) that provides users with the actual
time.

In each cycle of the divided real-time clock, there is a Hertz interrupt
generated to the RISC.  Users can also configure an alarm (RTC_ALARM).
When RTC_COUNTER matches the alarm, there will be an alarm interrupt
generated to the RISC.

The system RTC can generate an alarm wake-up signal to notify the power
controller to wake up from power saving mode.
Signed-off-by: NXianglong Du <Xianglong.Du@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 4c94c8b5 "ARM: tegra: update device trees for USB binding rework"
added regulator definitions for GPIO-controlled USB VBUS. However, none
of these contained the essential DT property enable-active-high. Add
this so that the regulator definitions are correct.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This patch renames the combatible strings for hdmi, mixer, ddc
and hdmiphy. It follows the convention of using compatible string
which represent the SoC in which the IP was added for the first
time.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Instead of using a GPIO to turn on/off the CAN transceiver, it is better to
use a regulator as some systems may use a PMIC to power the CAN transceiver.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This alters the local side address of the iospace to zero,
non prefetchable memory local side address to 0x00000000 and
prefetchable memory local side address to 0x10000000,
so as to match the values actually poked in by the driver.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

function-mask DT property is now a mask for a pin at each pin offset
inside a given pincontrol register. Fix DA850 DT data to reflect
this change.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
[nsekhar@ti.com: reword commit message for clarity]
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch adds pcie controller node for exynos5440-ssdk5440,
and also adds a phandle for pin controller node.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Exynos5440 has two PCIe controllers which can be used as root complex
for PCIe interface.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>

Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NWenyou Yang <wenyou.yang@atmel.com>

In previous version of SPI driver we where using different compatibility stings
for finding SPI features. We are now using the IP revision information.
So we stay with the unique compatibility string for this driver:
"atmel,at91rm9200-spi".
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NWenyou Yang <wenyou.yang@atmel.com>

B2020 ADI board is reference board for STIH415/416 SOCs, it has 2 x
UART, 4x USB, 1 x Ethernet, 1 x SATA, 1 x PCIe, and 2GB RAM  with
standard set-top box IPs.

This patch adds initial support to B2020 with STiH415/416 with SBC_UART1
as console and a heard beat LED.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

B2000 board is reference board for STIH415/416 SOCs, it has
2 x UART, 4x USB, 2 x Ethernet, 1 x SATA, 1 x PCIe, and 1GB RAM.

This patch add initial support to b2000 with STiH415/416 with UART2 as
console and a heard beat LED.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The STiH416 is advanced HD AVC processor with 3D graphics acceleration
and 1.2-GHz ARM Cortex-A9 SMP CPU.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The STiH415 is the next generation of HD, AVC set-top box processors for
satellite, cable, terrestrial and IP-STB markets. It is an ARM Cortex-A9
1.0 GHz, dual-core CPU.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The length of the registers area for the Marvell 370/XP Ethernet controller
was incorrect in the .dtsi: 0x2500, while it should have been 0x4000.
This problem wasn't noticed because there used to be a static mapping for
all the MMIO register region set up by ->map_io().

The register length was fixed in all the other device tree files,
except from the armada-xp-mv78260.dtsi, in the following commit:

  commit cf8088c5
  Author: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  Date:   Tue May 21 12:33:27 2013 +0200

    arm: mvebu: fix length of Ethernet registers area in .dtsi

This commit fixes a kernel panic in mvneta_probe(), when the kernel
tries to access the unmapped registers:

[  163.639092] mvneta d0070000.ethernet eth0: mac: 6e:3c:4f:87:17:2e
[  163.646962] mvneta d0074000.ethernet eth1: mac: 6a:04:4e:6f:f5:ef
[  163.654853] mvneta d0030000.ethernet eth2: mac: 2a:99:19:19:fc:4c
[  163.661258] Unable to handle kernel paging request at virtual address f011bcf0
[  163.668523] pgd = c0004000
[  163.671237] [f011bcf0] *pgd=2f006811, *pte=00000000, *ppte=00000000
[  163.677565] Internal error: Oops: 807 [#1] SMP ARM
[  163.682370] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc6-01850-gba0682e #11
[  163.690046] task: ef04c000 ti: ef03e000 task.ti: ef03e000
[  163.695467] PC is at mvneta_probe+0x34c/0xabc
[...]
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch adds device trees for describing the TI-Nspire hardware.

Changes between v1 and v2:
* Change "keymap" binding to the standard "linux,keymap" binding.
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Although the internal register window size is 1 MiB, the previous
ranges translation for the internal register space had a size of
0x4000000. This was done to allow the crypto and nand node to access
the corresponding 'sram' and 'nand' decoding windows.

In order to describe the hardware more accurately, we declare the
real 1 MiB internal register space in the ranges, and add a translation
entry for the nand node to access the 'nand' window.

This commit will make future improvements on the MBus DT binding easier.
Signed-off-by: NEzequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

When this node was added, the AB8500 GPIO driver was pretty broken.
As a hack, we pretended that NOMADIK GPIO 26 was the correct on/off
pin, as it was unused. It worked because AB8500 GPIO 26 was in an
'always on from boot' state. Now the AB8500 GPIO driver is working,
the default state for all the pins is 'off'. Let's flip back over to
use the correct GPIO which is _actually_ attached to the regulator.

We're also taking the opportunity to straighten out some formatting
misdemeanours, swapping spaces for tabs.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Here we're adding a node for the AB8500 GPIO device. This will allow
other DT:ed components to obtain GPIOs for use within their drivers.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

This adds a generic devicetree board file and a dtsi for boards
based on the RK3066a SoCs from Rockchip.

Apart from the generic parts (gic, clocks, pinctrl) the only components
currently supported are the timers, uarts and mmc ports (all DesignWare-
based).
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NOlof Johansson <olof@lixom.net>

This adds a basic clock setup for rk3066a SoCs. Only the gates are
set up currently, as the mux and dividers should use the upcoming
generic devicetree bindings.

Clocks whose rates need to be known are supplied by fixed-rate
"dummy"-clocks that provide the correct rate. This is uncritical insofar
that the only bootloader currently in existence for Rockchip devices
is the propietary Rockchip one that always setups the clocks in the
necessary way.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NMike Turquette <mturquette@linaro.org>

CodingStyle does not allow C99 style comments. Since the
dts files live in the kernel for now, make this compliant.
Signed-off-by: NMatt Porter <matt.porter@linaro.org>
Acked-by: NChristian Daudt <csd@broadcom.com>

Add SDHCI bindings for the Broadcom 281xx SoCs.

Changes from V2:
 - Documentation cleanups

Changes from V1:
 - split original patch into 2, one for driver and this one for dt
Signed-off-by: NChristian Daudt <csd@broadcom.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Replace /include/ by #include for da850 device tree files, in order to
use the C pre-processor, making use of #define features possible.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This revamps the device tree to fit with the new clock
implementation and brings it quite a bit closer to how
the hardware actually works.

After this the clock implementation knows about all
clock gates and will gate off all unused clocks at
boot time and save a bit of power.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

USB Host PHY clock on port 2 must be configured to 19.2MHz.
Provide this information.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.

As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.

CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for the USB host
pins.

HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830Signed-off-by: NRoger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The Armada 370 RD board has two internal mini-PCIe connectors. This
commit adds the necessary Device Tree informations to enable the usage
of those mini-PCIe connectors.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

Add the required pin configuration support to EXYNOS5420
using pinctrl interface.
Signed-off-by: NLeela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Tested-by : Sunil Joshi <joshi@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Add AM43x ePOS EVM minimal DT source - this is a minimal one to get
it booting. Also include it in omap2plus dtbs and document bindings.
The hardware is under development.
Signed-off-by: NAfzal Mohammed <afzal@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add bandgap device DT entry for OMAP5 dtsi.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NEduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
[benoit.cousson@linaro.org: Fix alignement and use the macros
for IRQ attributes]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for RGMII based CPSW ethernet to am335x-evm.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for RGMII based CPSW ethernet to AM335x EVMsk.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add pinmux configurations for MII based CPSW ethernet to am335x-bone.

Default mode is nothing but the values required for the module during
active state. With this configurations module is functional as
expected.

Sleep mode is nothing but the values required for the module during
inactive state. The pins are configured to its reset state to optimize
energy usage for the pins for the suspend/resume cycle
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Commit c971ff18 'leds: leds-pwm: Defer led_pwm_set() if PWM can sleep'
fixed a crash when using a trigger with a pwm-led provided by an
external chip. Now it is safe to add the default trigger according
to board-overo.c.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

The LED is active low, not active high.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>