This allows invoking an additional callback under the
socket spin lock.

Will be used by the next patches to avoid additional
spin lock contention.
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Reviewed-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Camelia Groza says:

====================
dpaa_eth: add XDP support

Enable XDP support for the QorIQ DPAA1 platforms.

Implement all the current actions (DROP, ABORTED, PASS, TX, REDIRECT). No
Tx batching is added at this time.

Additional XDP_PACKET_HEADROOM bytes are reserved in each frame's headroom.

After transmit, a reference to the xdp_frame is saved in the buffer for
clean-up on confirmation in a newly created structure for software
annotations. DPAA_TX_PRIV_DATA_SIZE bytes are reserved in the buffer for
storing this structure and the XDP program is restricted from accessing
them.

The driver shares the egress frame queues used for XDP with the network
stack. The DPAA driver is a LLTX driver so no explicit locking is required
on transmission.
====================

Link: https://lore.kernel.org/r/cover.1606322126.git.camelia.groza@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

For XDP TX, even tough we start out with correctly aligned buffers, the
XDP program might change the data's alignment. For REDIRECT, we have no
control over the alignment either.

Create a new workaround for xdp_frame structures to verify the erratum
conditions and move the data to a fresh buffer if necessary. Create a new
xdp_frame for managing the new buffer and free the old one using the XDP
API.

Due to alignment constraints, all frames have a 256 byte headroom that
is offered fully to XDP under the erratum. If the XDP program uses all
of it, the data needs to be move to make room for the xdpf backpointer.

Disable the metadata support since the information can be lost.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Explicitly point that the current workaround addresses skbs. This change is
in preparation for adding a workaround for XDP scenarios.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

After transmission, the frame is returned on confirmation queues for
cleanup. For this, store a backpointer to the xdp_frame in the private
reserved area at the start of the TX buffer.

No TX batching support is implemented at this time.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Use an xdp_frame structure for managing the frame. Store a backpointer to
the structure at the start of the buffer before enqueueing for cleanup
on TX confirmation. Reserve DPAA_TX_PRIV_DATA_SIZE bytes from the frame
size shared with the XDP program for this purpose. Use the XDP
API for freeing the buffer when it returns to the driver on the TX
confirmation path.

The frame queues are shared with the netstack. The DPAA driver is a LLTX
driver so no explicit locking is required on transmission.

This approach will be reused for XDP REDIRECT.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Implement the ndo_change_mtu callback to prevent users from setting an
MTU that would permit processing of S/G frames. The maximum MTU size
is dependent on the buffer size.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Implement the XDP_DROP and XDP_PASS actions.

Avoid draining and reconfiguring the buffer pool at each XDP
setup/teardown by increasing the frame headroom and reserving
XDP_PACKET_HEADROOM bytes from the start. Since we always reserve an
entire page per buffer, this change only impacts Jumbo frame scenarios
where the maximum linear frame size is reduced by 256 bytes. Multi
buffer Scatter/Gather frames are now used instead in these scenarios.

Allow XDP programs to access the entire buffer.

The data in the received frame's headroom can be overwritten by the XDP
program. Extract the relevant fields from the headroom while they are
still available, before running the XDP program.

Since the headroom might be resized before the frame is passed up to the
stack, remove the check for a fixed headroom value when building an skb.

Allow the meta data to be updated and pass the information up the stack.

Scatter/Gather frames are dropped when XDP is enabled.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

We maintain an skb backpointer in the software annotations area of Tx
frames. Introduce a structure for explicit handling.
Acked-by: NMadalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: NCamelia Groza <camelia.groza@nxp.com>
Reviewed-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Alex Elder says:

====================
net: ipa: start adding IPA v4.5 support

This series starts updating the IPA code to support IPA hardware
version 4.5.

The first patch fixes a problem found while preparing these updates.
Testing shows the code works with or without the change, and with
the fix the code matches "downstream" Qualcomm code.

The second patch updates the definitions for IPA register offsets
and field masks to reflect the changes that come with IPA v4.5.  A
few register updates have been deferred until later, because making
use of them involves some nontrivial code updates.

One type of change that IPA v4.5 brings is expanding the range of
certain configuration values.  High-order bits are added in a few
cases, and the third patch implements the code changes necessary to
use those newly available bits.

The fourth patch implements several fairly minor changes to the code
required for IPA v4.5 support.

The last two patches implement changes to the GSI registers used for
IPA.  Almost none of the registers change, but the range of memory
in which most of the GSI registers is located is shifted by a fixed
amount.  The fifth patch updates the GSI register definitions, and
the last patch implements the memory shift for IPA v4.5.
====================

Link: https://lore.kernel.org/r/20201125204522.5884-1-elder@linaro.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The offsets for almost all GSI registers we use have different
offsets starting at IPA version 4.5.  Only two registers remain
in their original location.

In a way though, the new register locations are not *that*
different.  The entire group of affected registers has simply
been shifted down in memory by a fixed amount (0xd000).  So for
example, the channel context 0 register that has a base offset of
0x0001c000 for "older" hardware now has a base offset of 0x0000f000.

This patch aims to add support for IPA v4.5 registers at their new
offets in a way that minimizes the amount of code that needs to
change.  It is not ideal, but it avoids the need to maintain
a nearly complete set of additional register offset definitions.

The approach takes advantage of the fact that when accessing GSI
registers we do not access any of memory at lower end of the "gsi"
memory range (with two exceptions already noted).  In particular,
we do not access anything within the bottom 0xd000 bytes of the
GSI memory range.

For IPA version 4.5, after we map the GSI memory, we adjust the
virtual memory pointer downward by the fixed amount (0xd000).
That way, register accesses using the offsets defined by the
existing GSI_REG_*() macros will resolve to the proper locations
for IPA version 4.5.

The two registers *not* affected by this offset are accessed only
in gsi_irq_setup().  There, for IPA version 4.5, we undo the general
register adjustment by adding the fixed amount back to the virtual
address to access these registers.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Very few GSI register definitions change for IPA v4.5, however
as a group their position in memory shifts a constant amount
(handled by the next commit).

Add definitions and update comments to the set of GSI registers to
support changes that come with IPA v4.5.

Update the logic in gsi_channel_program() to accommodate the new
(expanded) PREFETCH_MODE field in the CH_C_QOS register.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Update the IPA code to make use of the updated IPA v4.5 register
definitions.  Generally what this patch does is, if IPA v4.5
hardware is in use:
  - Ensure new registers or fields in IPA v4.5 are updated where
    required
  - Ensure registers or fields not supported in IPA v4.5 are not
    examined when read, or are set to 0 when written
It does this while preserving the existing functionality for IPA
versions lower than v4.5.

The values to program for QSB_MAX_READS and QSB_MAX_WRITES and the
source and destination resource counts are updated to be correct for
all versions through v4.5 as well.

Note that IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
already reflect that 5 is an acceptable number of resources (which
IPA v4.5 implements).
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

IPA v4.5 adds a few fields to the endpoint header and extended
header configuration registers that represent new high-order bits
for certain offsets and sizes.  Add code to incorporate these upper
bits into the registers for IPA v4.5.

This includes creating ipa_header_size_encoded(), which handles
encoding the metadata offset field for use in the ENDP_INIT_HDR
register in a way appropriate for the hardware version.  This and
ipa_metadata_offset_encoded() ensure the mask argument passed to
u32_encode_bits() is constant.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Update "ipa_reg.h" so that register definitions support IPA hardware
version 4.5, in addition to versions 3.5.1 through v4.2.  Most of
the register definitions are the same, but in some cases fields are
added, changed, or eliminated.

Updates for a few IPA v4.5 registers are more complex, and adding
those definition will be deferred to separate patches.  This patch
only updates the register offset and field definitions, and adds
informational comments.

The only code change avoids accessing the backward compatibility
register for IPA version 4.5 in ipa_hardware_config().  Other IPA
v4.5-specific code changes will come later.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Starting with IPA v4.2 there is a GSI channel option to use an
"escape buffer" instead of prefetch buffers.  This should be used
for all channels *except* the AP command TX channel.  The logic
that implements this has it backwards; fix this bug.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

By setting NF_FLOWTABLE_COUNTER. Otherwise, the updates added by
commit ef803b3c ("netfilter: flowtable: add counter support in HW
offload") are not effective when using act_ct.

While at it, now that we have the flag set, protect the call to
nf_ct_acct_update() by commit beb97d3a ("net/sched: act_ct: update
nf_conn_acct for act_ct SW offload in flowtable") with the check on
NF_FLOWTABLE_COUNTER, as also done on other places.

Note that this shouldn't impact performance as these stats are only
enabled when net.netfilter.nf_conntrack_acct is enabled.
Signed-off-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Nwenxu <wenxu@ucloud.cn>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Link: https://lore.kernel.org/r/481a65741261fd81b0a0813e698af163477467ec.1606415787.git.marcelo.leitner@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Trivial conflict in CAN, keep the net-next + the byteswap wrapper.

Conflicts:
	drivers/net/can/usb/gs_usb.c
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Jon Maloy says:

====================
tipc: some minor improvements

We add some improvements that will be useful in future commits.
====================

Link: https://lore.kernel.org/r/20201125182915.711370-1-jmaloy@redhat.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

We update the terminology in the code so that deprecated structure
names and macros are replaced with those currently recommended in
the user API.

struct tipc_portid   -> struct tipc_socket_addr
struct tipc_name     -> struct tipc_service_addr
struct tipc_name_seq -> struct tipc_service_range

TIPC_ADDR_ID       -> TIPC_SOCKET_ADDR
TIPC_ADDR_NAME     -> TIPC_SERVICE_ADDR
TIPC_ADDR_NAMESEQ  -> TIPC_SERVICE_RANGE
TIPC_CFG_SRV       -> TIPC_NODE_STATE
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The 32-bit node number, aka node hash or node address, is calculated
based on the 128-bit node identity when it is not set explicitly by
the user. In future commits we will need to perform this hash operation
on peer nodes while feeling safe that we obtain the same result.

We do this by interpreting the initial hash as a network byte order
number. Whenever we need to use the number locally on a node
we must therefore translate it to host byte order to obtain an
architecure independent result.

Furthermore, given the context where we use this number, we must not
allow it to be zero unless the node identity also is zero. Hence, in
the rare cases when the xor-ed hash value may end up as zero we replace
it with a fix number, knowing that the code anyway is capable of
handling hash collisions.
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

We refactor the tipc_sk_bind() function, so that the lock handling
is handled separately from the logics. We also move some sanity
tests to earlier in the call chain, to the function tipc_bind().
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

After migration to the shared interrupt support, the KSZ8031 PHY with
enabled interrupt support was not able to notify about link status
change.

Fixes: 59ca4e58 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201127123621.31234-1-o.rempel@pengutronix.deSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Martin Schiller says:

====================
net/x25: netdev event handling
====================

Link: https://lore.kernel.org/r/20201126063557.1283-1-ms@dev.tdt.deSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Remove obsolete function x25_kill_by_device(). It's not used any more.
Signed-off-by: NMartin Schiller <ms@dev.tdt.de>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

We have to take the actual link state into account to handle
restart requests/confirms well.
Signed-off-by: NMartin Schiller <ms@dev.tdt.de>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

1. DTE interface changes immediately to LAPB_STATE_1 and start sending
   SABM(E).

2. DCE interface sends N2-times DM and changes to LAPB_STATE_1
   afterwards if there is no response in the meantime.
Signed-off-by: NMartin Schiller <ms@dev.tdt.de>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch allows layer2 (LAPB) to react to netdev events itself and
avoids the detour via layer3 (X.25).

1. Establish layer2 on NETDEV_UP events, if the carrier is already up.

2. Call lapb_disconnect_request() on NETDEV_GOING_DOWN events to signal
   the peer that the connection will go down.
   (Only when the carrier is up.)

3. When a NETDEV_DOWN event occur, clear all queues, enter state
   LAPB_STATE_0 and stop all timers.

4. The NETDEV_CHANGE event makes it possible to handle carrier loss and
   detection.

   In case of Carrier Loss, clear all queues, enter state LAPB_STATE_0
   and stop all timers.

   In case of Carrier Detection, we start timer t1 on a DCE interface,
   and on a DTE interface we change to state LAPB_STATE_1 and start
   sending SABM(E).
Signed-off-by: NMartin Schiller <ms@dev.tdt.de>
Acked-by: NXie He <xie.he.0141@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

1. Add / remove x25_link_device by NETDEV_REGISTER/UNREGISTER and also
   by NETDEV_POST_TYPE_CHANGE/NETDEV_PRE_TYPE_CHANGE.

   This change is needed so that the x25_neigh struct for an interface
   is already created when it shows up and is kept independently if the
   interface goes UP or DOWN.

   This is used in an upcomming commit, where x25 params of an neighbour
   will get configurable through ioctls.

2. NETDEV_CHANGE event makes it possible to handle carrier loss and
   detection. If carrier is lost, clean up everything related to this
   neighbour by calling x25_link_terminated().

3. Also call x25_link_terminated() for NETDEV_DOWN events and remove the
   call to x25_clear_forward_by_dev() in x25_route_device_down(), as
   this is already called by x25_kill_by_neigh() which gets called by
   x25_link_terminated().

4. Do nothing for NETDEV_UP and NETDEV_GOING_DOWN events, as these will
   be handled in layer 2 (LAPB) and layer3 (X.25) will be informed by
   layer2 when layer2 link is established and layer3 link should be
   initiated.
Signed-off-by: NMartin Schiller <ms@dev.tdt.de>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Ido Schimmel says:

====================
mlxsw: Update adjacency index more efficiently

The device supports an operation that allows the driver to issue one
request to update the adjacency index for all the routes in a given
virtual router (VR) from old index and size to new ones. This is useful
in case the configuration of a certain nexthop group is updated and its
adjacency index changes.

Currently, the driver does not use this operation in an efficient
manner. It iterates over all the routes using the nexthop group and
issues an update request for the VR if it is not the same as the
previous VR.

Instead, this patch set tracks the VRs in which the nexthop group is
used and issues one request for each VR.

Example:

8k IPv6 routes were added in an alternating manner to two VRFs. All the
routes are using the same nexthop object ('nhid 1').

Before:

 Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':

            16,385      devlink:devlink_hwmsg

       4.255933213 seconds time elapsed

       0.000000000 seconds user
       0.666923000 seconds sys

Number of EMAD transactions corresponds to number of routes using the
nexthop group.

After:

 Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':

                 3      devlink:devlink_hwmsg

       0.077655094 seconds time elapsed

       0.000000000 seconds user
       0.076698000 seconds sys

Number of EMAD transactions corresponds to number of VRFs / VRs.

Patch set overview:

Patch #1 is a fix for a bug introduced in previous submission. Detected
by Coverity.

Patches #2 and #3 are preparations.

Patch #4 tracks the VRs a nexthop group is member of.

Patch #5 uses the membership tracking from the previous patch to issue
one update request per each VR.
====================

Link: https://lore.kernel.org/r/20201125193505.1052466-1-idosch@idosch.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

The device supports an operation that allows the driver to issue one
request to update the adjacency index for all the routes in a given
virtual router (VR) from old index and size to new ones. This is useful
in case the configuration of a certain nexthop group is updated and its
adjacency index changes.

Currently, the driver does not use this operation in an efficient
manner. It iterates over all the routes using the nexthop group and
issues an update request for the VR if it is not the same as the
previous VR.

Instead, use the VR tracking added in the previous patch to update the
adjacency index once for each VR currently using the nexthop group.

Example:

8k IPv6 routes were added in an alternating manner to two VRFs. All the
routes are using the same nexthop object ('nhid 1').

Before:

# perf stat -e devlink:devlink_hwmsg --filter='incoming==0' -- ip nexthop replace id 1 via 2001:db8:1::2 dev swp3

 Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':

            16,385      devlink:devlink_hwmsg

       4.255933213 seconds time elapsed

       0.000000000 seconds user
       0.666923000 seconds sys

Number of EMAD transactions corresponds to number of routes using the
nexthop group.

After:

# perf stat -e devlink:devlink_hwmsg --filter='incoming==0' -- ip nexthop replace id 1 via 2001:db8:1::2 dev swp3

 Performance counter stats for 'ip nexthop replace id 1 via 2001:db8:1::2 dev swp3':

                 3      devlink:devlink_hwmsg

       0.077655094 seconds time elapsed

       0.000000000 seconds user
       0.076698000 seconds sys

Number of EMAD transactions corresponds to number of VRFs / VRs.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

For each nexthop group, track in which virtual routers (VRs) the group is
used. This is going to be used by the next patch to perform a more
efficient adjacency index update whenever the group's adjacency index
changes.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

In the rare case where the adjacency pointer cannot be updated for a
given virtual router, rollback the operation so that virtual routers
that are already using the new index will use the old one again.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

mlxsw_sp_adj_index_mass_update_vr() only needs the virtual router's
identifier and protocol, so pass them directly. In a subsequent patch
the caller will not have access to the pointer.
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NJiri Pirko <jiri@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Return error to the caller instead of suppressing it.

Fixes: e3ddfb45 ("mlxsw: spectrum_router: Allow returning errors from mlxsw_sp_nexthop_group_refresh()")
Addresses-Coverity: ("Error handling issues  (CHECKED_RETURN)")
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Merge tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic

Pull asm-generic fix from Arnd Bergmann:
 "Add correct MAX_POSSIBLE_PHYSMEM_BITS setting to asm-generic.

  This is a single bugfix for a bug that Stefan Agner found on 32-bit
  Arm, but that exists on several other architectures"

* tag 'asm-generic-fixes-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
  arch: pgtable: define MAX_POSSIBLE_PHYSMEM_BITS where needed

Pull ARM SoC fixes from Arnd Bergmann:
 "Another set of patches for devicetree files and Arm SoC specific
  drivers:

   - A fix for OP-TEE shared memory on non-SMP systems

   - multiple code fixes for the OMAP platform, including one regression
     for the CPSW network driver and a few runtime warning fixes

   - Some DT patches for the Rockchip RK3399 platform, in particular
     fixing the MMC device ordering that recently became
     nondeterministic with async probe.

   - Multiple DT fixes for the Tegra platform, including a regression
     fix for suspend/resume on TX2

   - A regression fix for a user-triggered fault in the NXP dpio driver

   - A regression fix for a bug caused by an earlier bug fix in the
     xilinx firmware driver

   - Two more DTC warning fixes

   - Sylvain Lemieux steps down as maintainer for the NXP LPC32xx
     platform"

* tag 'arm-soc-fixes-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
  arm64: tegra: Fix Tegra234 VDK node names
  arm64: tegra: Wrong AON HSP reg property size
  arm64: tegra: Fix USB_VBUS_EN0 regulator on Jetson TX1
  arm64: tegra: Correct the UART for Jetson Xavier NX
  arm64: tegra: Disable the ACONNECT for Jetson TX2
  optee: add writeback to valid memory type
  firmware: xilinx: Use hash-table for api feature check
  firmware: xilinx: Fix SD DLL node reset issue
  soc: fsl: dpio: Get the cpumask through cpumask_of(cpu)
  ARM: dts: dra76x: m_can: fix order of clocks
  bus: ti-sysc: suppress err msg for timers used as clockevent/source
  MAINTAINERS: Remove myself as LPC32xx maintainers
  arm64: dts: qcom: clear the warnings caused by empty dma-ranges
  arm64: dts: broadcom: clear the warnings caused by empty dma-ranges
  ARM: dts: am437x-l4: fix compatible for cpsw switch dt node
  arm64: dts: rockchip: Reorder LED triggers from mmc devices on rk3399-roc-pc.
  arm64: dts: rockchip: Assign a fixed index to mmc devices on rk3399 boards.
  arm64: dts: rockchip: Remove system-power-controller from pmic on Odroid Go Advance
  arm64: dts: rockchip: fix NanoPi R2S GMAC clock name
  ARM: OMAP2+: Manage MPU state properly for omap_enter_idle_coupled()
  ...

Pull networking fixes from Jakub Kicinski:
 "Networking fixes for 5.10-rc6, including fixes from the WiFi driver,
  and CAN subtrees.

  Current release - regressions:

   - gro_cells: reduce number of synchronize_net() calls

   - ch_ktls: release a lock before jumping to an error path

  Current release - always broken:

   - tcp: Allow full IP tos/IPv6 tclass to be reflected in L3 header

  Previous release - regressions:

   - net/tls: fix missing received data after fast remote close

   - vsock/virtio: discard packets only when socket is really closed

   - sock: set sk_err to ee_errno on dequeue from errq

   - cxgb4: fix the panic caused by non smac rewrite

  Previous release - always broken:

   - tcp: fix corner cases around setting ECN with BPF selection of
     congestion control

   - tcp: fix race condition when creating child sockets from syncookies
     on loopback interface

   - usbnet: ipheth: fix connectivity with iOS 14

   - tun: honor IOCB_NOWAIT flag

   - net/packet: fix packet receive on L3 devices without visible hard
     header

   - devlink: Make sure devlink instance and port are in same net
     namespace

   - net: openvswitch: fix TTL decrement action netlink message format

   - bonding: wait for sysfs kobject destruction before freeing struct
     slave

   - net: stmmac: fix upstream patch applied to the wrong context

   - bnxt_en: fix return value and unwind in probe error paths

  Misc:

   - devlink: add extra layer of categorization to the reload stats uAPI
     before it's released"

* tag 'net-5.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (68 commits)
  sock: set sk_err to ee_errno on dequeue from errq
  mptcp: fix NULL ptr dereference on bad MPJ
  net: openvswitch: fix TTL decrement action netlink message format
  can: af_can: can_rx_unregister(): remove WARN() statement from list operation sanity check
  can: m_can: m_can_dev_setup(): add support for bosch mcan version 3.3.0
  can: m_can: fix nominal bitiming tseg2 min for version >= 3.1
  can: m_can: m_can_open(): remove IRQF_TRIGGER_FALLING from request_threaded_irq()'s flags
  can: mcp251xfd: mcp251xfd_probe(): bail out if no IRQ was given
  can: gs_usb: fix endianess problem with candleLight firmware
  ch_ktls: lock is not freed
  net/tls: Protect from calling tls_dev_del for TLS RX twice
  devlink: Make sure devlink instance and port are in same net namespace
  devlink: Hold rtnl lock while reading netdev attributes
  ptp: clockmatrix: bug fix for idtcm_strverscmp
  enetc: Let the hardware auto-advance the taprio base-time of 0
  gro_cells: reduce number of synchronize_net() calls
  net: stmmac: fix incorrect merge of patch upstream
  ipv6: addrlabel: fix possible memory leak in ip6addrlbl_net_init
  Documentation: netdev-FAQ: suggest how to post co-dependent series
  ibmvnic: enhance resetting status check during module exit
  ...

wenxu says:

====================
net/sched: fix over mtu packet of defrag in

Currently kernel tc subsystem can do conntrack in act_ct. But when several
fragment packets go through the act_ct, function tcf_ct_handle_fragments
will defrag the packets to a big one. But the last action will redirect
mirred to a device which maybe lead the reassembly big packet over the mtu
of target device.

The first patch fix miss init the qdisc_skb_cb->mru
The send one refactor the hanle of xmit in act_mirred and prepare for the
third one
The last one add implict packet fragment support to fix the over mtu for
defrag in act_ct.
====================

Link: https://lore.kernel.org/r/1606276883-6825-1-git-send-email-wenxu@ucloud.cnSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Currently kernel tc subsystem can do conntrack in cat_ct. But when several
fragment packets go through the act_ct, function tcf_ct_handle_fragments
will defrag the packets to a big one. But the last action will redirect
mirred to a device which maybe lead the reassembly big packet over the mtu
of target device.

This patch add support for a xmit hook to mirred, that gets executed before
xmiting the packet. Then, when act_ct gets loaded, it configs that hook.
The frag xmit hook maybe reused by other modules.
Signed-off-by: Nwenxu <wenxu@ucloud.cn>
Acked-by: NCong Wang <cong.wang@bytedance.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>