Merge Richard's work to support SR-IOV on PowerNV. All generic PCI
patches acked by Bjorn.

Some minor conflicts with Daniel's pci_controller_ops work.

Conflicts:
	arch/powerpc/include/asm/machdep.h
	arch/powerpc/platforms/powernv/pci-ioda.c

Memory dlpar handling can return from dlpar_memory() without releasing the
device_hotplug lock. Correct this routine to ensure the lock is released.

Fixes: 5f97b2a0 ("powerpc/pseries: Implement memory hotplug add in the kernel")
Signed-off-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Merge series from Nathan Fontenot to do memory hotplug in the kernel.

This problem appears to have been introduced in 2.6.29 by commit
93197a36 "Rewrite sysfs processor cache info code".

This caused lscpu to error out on at least e500v2 devices, eg:

  error: cannot open /sys/devices/system/cpu/cpu0/cache/index2/size: No such file or directory

Some embedded powerpc systems use cache-size in DTS for the unified L2
cache size, not d-cache-size, so we need to allow for both DTS names.
Added a new CACHE_TYPE_UNIFIED_D cache_type_info structure to handle
this.

Fixes: 93197a36 ("powerpc: Rewrite sysfs processor cache info code")
Signed-off-by: NDave Olson <olson@cumulusnetworks.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The hard lockup detector uses a PMU event as a periodic NMI to
detect if we are stuck (where stuck means no timer interrupts have
occurred).

Ben's rework of the ppc64 soft disable code has made ppc64 PMU
exceptions a partial NMI. They can get disabled if an external
interrupt comes in, but otherwise PMU interrupts will fire in
interrupt disabled regions.

We disable the hard lockup detector by default for a few reasons:

- It breaks userspace event based branches on POWER8.
- It is likely to produce false positives on KVM guests.
- Since PMCs can only count to 2^31, counting cycles means we might
  take multiple PMU exceptions per second per hardware thread even
  if our hard lockup timeout is 10 seconds.

It can be enabled via a boot option, or via procfs.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We want to enable the hard lockup detector on ppc64, but right now
that enables the oprofile NMI timer too.

We'd prefer not to enable the oprofile NMI timer, it adds another
element to our PMU testing and it requires us to increase our
exported symbols (eg cpu_khz).

Modify the config entry for OPROFILE_NMI_TIMER to disable it on PPC64.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Acked-by: NRobert Richter <rric@kernel.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add missing put_cpu_var() for 24x7 requests. This went missing in
commit f34b6c72 (3.18-rc3).
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Break up the function single_24x7_request() into smaller functions.
This would later enable us to "prepare" a multi-event request
buffer and then submit a single hcall for several events.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move the code to update an event count into a new function,
update_event_count().
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix minor whitespace damages.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move code that maps a perf_event to a 24x7 request buffer into a
separate function, add_event_to_24x7_request().
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

For consistency with the pmu operation ->read() and with other
pmus, rename hv_24x7_event_update() to hv_24x7_event_read().
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To simplify/cleanup code, move the rather long printk() to a separate
function.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The function event_24x7_request() is essentially a wrapper to the
function single_24x7_request() and can be dropped to simplify code.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use pr_devel_ratelimited() to log error message when the 24x7 HCALL
fails. Since users specify events by their sysfs name, the HCALL should
succeed. Any errors reported by the HCALL would be of interest to the
developer, rather than the user/administrator.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove the 'success_expected' parameter and log the message unconditionally.
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The parameters to the 24x7 HCALL have variable number of elements in them.
Set the minimum number of such elements to 1 rather than 0 and eliminate
the temporary structures.

This would enable us to submit multiple counter requests and process
multiple results from a single HCALL (in a follow on patch).
Signed-off-by: NSukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This change adds the OPAL interface definitions to allow Linux to read,
write and erase from system flash devices. We register platform devices
for the flash devices exported by firmware.

We clash with the existing opal_flash_init function, which is really for
the FSP flash update functionality, so we rename that initcall to
opal_flash_update_init().

A future change will add an mtd driver that uses this interface.

Changes from Joel Stanley and Jeremy Kerr.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NJoel Stanley <joel@jms.id.au>
Acked-by: NStewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Check that a syscall made during an active transaction will fail with
the correct failure code and that one made during a suspended
transaction will succeed.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move get_auxv_entry() from pmu/lib.c up to harness.c in order to make
it available to other tests.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This patch changes the syscall handler to doom (tabort) active
transactions when a syscall is made and return immediately without
performing the syscall.

Currently, the system call instruction automatically suspends an
active transaction which causes side effects to persist when an active
transaction fails.

This does change the kernel's behaviour, but in a way that was
documented as unsupported. It doesn't reduce functionality because
syscalls will still be performed after tsuspend. It also provides a
consistent interface and makes the behaviour of user code
substantially the same across powerpc and platforms that do not
support suspended transactions (e.g. x86 and s390).

Performance measurements using
http://ozlabs.org/~anton/junkcode/null_syscall.c
indicate the cost of a system call increases by about 0.5%.
Signed-off-by: NSam Bobroff <sam.bobroff@au1.ibm.com>
Acked-By: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Now that we have ported the calls to iommu_init_early_dart to always
supply a pci_controller_ops struct, we can safely drop the check.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove shims, patch callsites to use pci_controller_ops
versions instead.

Also move back the probe mode defines, as explained in the patch
for pci_probe_mode.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the Cell platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move the installation of DMA operations out of swiotlb's subsys
initcall, and into the generic PCI controller operations struct.

These ops are installed conditionally, based on the ppc_swiotlb_enable
global. The global can be set in two places:
 - swiotlb_detect_4g, which is always called at the arch initcall level
 - setup_pci_atmu, which is called as part of the fsl_add_bridge and
fsl_pci_syscore_do_resume.

fsl_pci_syscore_do_resume is called late enough that any changes as a
result of that call will have no effect.

As such, if we test the global and set the operations as part of
fsl_add_bridge, after the call to setup_pci_atmu, we can be confident
that it will cover all the PCI implementations affected by the changes
to dma-swiotlb.c.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the Maple platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the PaSemi platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the PowerNV platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the pSeries platform to use the pci_controller_ops structure,
rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This moves the Power Mac platform to use the pci_controller_ops
structure rather than ppc_md for PCI controller operations.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If a pci_controller_ops struct is provided to iommu_init_early_dart,
populate that with the DMA setup ops, rather than ppc_md. If NULL is
provided, populate ppc_md as before.

This also patches the call sites for Maple and Power Mac to pass
NULL, so existing behaviour is preserved.

The benefit of making this optional is that it means we don't have
to change dart, Maple and Power Mac over to the controller_ops
system in one fell swoop.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.reset_secondary_bus,
shadowing ppc_md.pcibios_reset_secondary_bus.
Add a shim, and changes the callsites to use the shim.

Use pcibios_reset_secondary_bus_shim, as both
pcibios_reset_secondary_bus and pci_reset_secondary_bus
are already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.window_alignment,
shadowing ppc_md.pcibios_window_alignment.
Add a shim, and changes the callsites to use the shim.

Here, we use pci_window_alignment, as pcibios_window_alignment is
already taken.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.enable_device_hook,
shadowing ppc_md.pcibios_enable_device_hook.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.probe_mode, shadowing ppc_md.pci_probe_mode.
Add a shim, and changes the callsites to use the shim.

We also need to move the probe mode defines to pci-bridge.h from pci.h.
They are required by the shim in order to return a sensible default.
Previously, the were defined in pci.h, but pci.h includes pci-bridge.h
before the relevant #defines. This means the definitions are absent
if pci.h is included before pci-bridge.h. This occurs in some drivers.
So, move the definitons now, and move them back when we remove the shim.

Anything that wants the defines would have had to include pci.h, and
since pci.h includes pci-bridge.h, nothing will lose access to the
defines.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add pci_controller_ops.dma_bus_setup, shadowing ppc_md.pci_dma_bus_setup.
Add a shim, and changes the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Introduces the pci_controller_ops structure.
Add pci_controller_ops.dma_dev_setup, shadowing ppc_md.pci_dma_dev_setup.
Add a shim, and change the callsites to use the shim.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

pcibios_enable_device_hook returned an int. Every implementation
returned either -EINVAL or 0. The return value wasn't propagated by
the caller: any non-zero return value caused pcibios_enable_device
to return -EINVAL itself. Therefore, make the hook return a bool.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>