Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.

Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.

Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: NIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: NIoana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.

New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
  between mac and phy is disabled. Instead phylib is used like in
  other typical Linux drivers. The usage of phylib allows to
  specify fixed-link parameters in the device tree.

. The device tree entry phy-connection-type is supported now with
  the modes RGMII or (G)MII (default).

Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
  configurations with phy. Microchip kindly offered testing
  as soon as the Corona measures allow this.

. All review findings of Andrew Lunn are included

Example:
--------
&pcie {
	status = "okay";

	host@0 {
		reg = <0 0 0 0 0>;

		#address-cells = <3>;
		#size-cells = <2>;

		ethernet@0 {
			compatible = "weyland-yutani,noscom1", "microchip,lan743x";
			status = "okay";
			reg = <0 0 0 0 0>;
			phy-connection-type = "rgmii";

			fixed-link {
				speed = <100>;
				full-duplex;
			};
		};
	};
};
Signed-off-by: NRoelof Berg <rberg@berg-solutions.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.

A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:

1. Packets might not need to be marked with 'offload_fwd_mark'. For
   example, if packet was trapped before L2 forwarding

2. Packets might not need to be injected to the kernel's Rx path. For
   example, sampled packets are reported to user space via the psample
   module

Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: NLiu Xiang <liuxiang_1999@126.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.

The patch has been successfully tested on Octeon II.

Fixes: a999933d ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().

No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The caller doesn't care about the error codes, they only check for zero
vs non-zero.  Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1.  We can also return
directly if there is a failure.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode
("RGMII-*ID") settings, but used the hardware defaults, augmented by
explicit configuration of individual skew values using the "*-skew-ps"
DT properties.  The lack of PHY mode support was compensated by the
EtherAVB MAC driver, which configures TX and/or RX internal delay
itself, based on the PHY mode.

However, now the KSZ9031 driver has gained PHY mode support, delays may
be configured twice, causing regressions.  E.g. on the Renesas
Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca.
400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp.

As internal delay configuration supported by the KSZ9031 PHY is too
limited for some use cases, the ability to configure MAC internal delay
is deemed useful and necessary.  Hence a proper fix would involve
splitting internal delay configuration in two parts, one for the PHY,
and one for the MAC.  However, this would require adding new DT
properties, thus breaking DTB backwards-compatibility.

Hence fix the regression in a backwards-compatibility way, by letting
the EtherAVB driver mask the PHY mode when it has inserted a delay, to
avoid the PHY driver adding a second delay.  This also fixes messages
like:

    Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii"

as the PHY no longer sees the original RGMII-*ID mode.

Solving the issue by splitting configuration in two parts can be handled
in future patches, and would require retaining a backwards-compatibility
mode anyway.

Fixes: bcf3440c ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify handling the power management callbacks.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Functionality for quiescing the chip is spread across different
functions currently. Move it to rtl8169_down().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move calls that are needed before and after calling rtl8169_hw_reset()
into this function. This requires to move the function in the code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In places where the indexes have to be reset, we call
rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We go to runtime-suspend few secs after cable removal. As cable is
removed "physical link up" is the only meaningful WoL source.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change driver private data type to struct rtl8169_private * to avoid
some overhead.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NETIF_F_HW_VLAN_CTAG_FILTER is not set in netdev->hw_feature for
the HNS3 driver, so the handler of NETIF_F_HW_VLAN_CTAG_FILTER
in hns3_nic_set_features() won't be called, remove it.
Reported-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a redundant blank line in hclgevf_cmd_set_promisc_mode(),
and fix a reverse xmas tree coding style issue in
hclgevf_set_rss_tc_mode().
Reported-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct hclgevf_dev stands for VF device, its field num_tqps
indicates the number of VF's task queue pairs, so the comment
is incorrect, replace 'PF' with 'VF'.
Reported-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro hclgevf_ring_to_dma_dir and hclgevf_is_csq defined in
hclgevf_cmd.c, but not used, so remove them.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro hclge_is_csq defined in hcgle_cmd.c has not been used,
so remove it.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use %d to print int variable 'ret' in hclge_mac_mdio_config().
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c:988:29:
error: symbol 'mlx5e_dcbnl_ops' was not declared. Should it be static?
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fixes sparse warnings:
warning: cast to restricted __be32
warning: restricted __be32 degrades to integer
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>

Fix some trivial warnings of the type:
warning: incorrect type in initializer (different base types)
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>

tls handle and rcd_sn are actually big endian and not in host format.
Fix that.

Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:177:21:
warning: cast to restricted __be64

drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:178:52:
warning: incorrect type in argument 2 (different base types)
    expected unsigned int [usertype] handle
    got restricted __be32 [usertype] handle
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15:
warning: memset with byte count of 271720

mlx5_cmd_stats array is too big to be held inline in mlx5_cmd.
Allocate it separately.
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

dr_ste_crc32_calc() calculates crc32 and should return it in HW format.
It is being used to calculate a u32 index, hence we force the return value
of u32 to avoid the sparse warning:

drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:115:16:
warning: incorrect type in return expression (different base types)
    expected unsigned int
    got restricted __be32 [usertype]
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>

raw_ip actual type is __be32 and not u32.
Fix that and get rid of the warning.

drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:906:31:
warning: cast to restricted __be32
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>

HW spec objects should receive a void ptr to work on, the MLX5_SET/GET
macro will know how to handle it.

No need to provide explicit or wrong pointer type in this case.

warning: incorrect type in argument 1 (different base types)
    expected unsigned long long const [usertype] *sw_action
    got restricted __be64 [usertype] *[assigned] sw_action
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>

Make use of generic API mpls_entry_encode() to build mpls label and get
rid of local function.
Signed-off-by: NEli Cohen <eli@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Moving the mlx5_ifc_query_qp_out_bits structure on the stack was a bit
excessive and now causes the compiler to complain on 32-bit architectures:

drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:274:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]

Revert the previous patch partially to use dynamically allocation as
the code did before. Unfortunately there is no good error handling
in case the allocation fails.

Fixes: 57a6c5e9 ("net/mlx5: Replace hand written QP context struct with automatic getters")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Clang warns:

drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:6: warning:
variable 'err' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
        if (IS_ERR(d->pkt_reformat)) {
            ^~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3718:6: note:
uninitialized use occurs here
        if (err)
            ^~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:2: note: remove the
'if' if its condition is always true
        if (IS_ERR(d->pkt_reformat)) {
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3670:9: note: initialize
the variable 'err' to silence this warning
        int err;
               ^
                = 0
1 warning generated.

It is not wrong, err is only ever initialized in if statements but this
one is not in one. Initialize err to 0 to fix this.

Fixes: 14e6b038 ("net/mlx5e: Add support for hw decapsulation of MPLS over UDP")
Link: https://github.com/ClangBuiltLinux/linux/issues/1037Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>