- 19 12月, 2017 3 次提交
-
-
由 Edward Cree 提交于
Log a message if PTP probing fails; if we then, unexpectedly, get PTP events, only log a message for the first one on each device. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
Medford2 can also have 16k or 64k VI stride. This is reported by MCDI in GET_CAPABILITIES, which fortunately is called before the driver does anything sensitive to the VI stride (such as accessing or even allocating VIs past the zeroth). Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
Support using BAR 0 on SFC9250, even though the driver doesn't bind to such devices yet. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 11月, 2017 1 次提交
-
-
由 Robert Stonehouse 提交于
Fixes: 535a6177 ("sfc: suppress handled MCDI failures when changing the MAC address") Signed-off-by: NBert Kenward <bkenward@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 11月, 2017 1 次提交
-
-
由 Edward Cree 提交于
Ethernet FCS inclusion (rx-fcs) is supported on EF10 NICs, conditional on a firmware capability bit (MC_CMD_GET_CAPABILITIES_OUT_RX_INCLUDE_FCS). To receive frames with bad FCS (rx-all) we just don't return the discard flag EFX_RX_PKT_DISCARD from efx_ef10_handle_rx_event_errors() or efx_farch_handle_rx_not_ok(). Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 10月, 2017 1 次提交
-
-
由 Mark Rutland 提交于
locking/atomics: COCCINELLE/treewide: Convert trivial ACCESS_ONCE() patterns to READ_ONCE()/WRITE_ONCE() Please do not apply this to mainline directly, instead please re-run the coccinelle script shown below and apply its output. For several reasons, it is desirable to use {READ,WRITE}_ONCE() in preference to ACCESS_ONCE(), and new code is expected to use one of the former. So far, there's been no reason to change most existing uses of ACCESS_ONCE(), as these aren't harmful, and changing them results in churn. However, for some features, the read/write distinction is critical to correct operation. To distinguish these cases, separate read/write accessors must be used. This patch migrates (most) remaining ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following coccinelle script: ---- // Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and // WRITE_ONCE() // $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch virtual patch @ depends on patch @ expression E1, E2; @@ - ACCESS_ONCE(E1) = E2 + WRITE_ONCE(E1, E2) @ depends on patch @ expression E; @@ - ACCESS_ONCE(E) + READ_ONCE(E) ---- Signed-off-by: NMark Rutland <mark.rutland@arm.com> Signed-off-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: davem@davemloft.net Cc: linux-arch@vger.kernel.org Cc: mpe@ellerman.id.au Cc: shuah@kernel.org Cc: snitzer@redhat.com Cc: thor.thayer@linux.intel.com Cc: tj@kernel.org Cc: viro@zeniv.linux.org.uk Cc: will.deacon@arm.com Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
-
- 13 7月, 2017 1 次提交
-
-
由 Bert Kenward 提交于
If we have more than 32 unicast MAC addresses assigned to an interface we will read beyond the end of the address table in the driver when adding filters. The next 256 entries store multicast addresses, so we will end up attempting to insert duplicate filters, which is mostly harmless. If we add more than 288 unicast addresses we will then read past the multicast address table, which is likely to be more exciting. Fixes: 12fb0da4 ("sfc: clean fallbacks between promisc/normal in efx_ef10_filter_sync_rx_mode") Signed-off-by: NBert Kenward <bkenward@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 6月, 2017 1 次提交
-
-
由 Edward Cree 提交于
When filter insertion fails with no rollback, we were trying to convert EFX_EF10_FILTER_ID_INVALID to an id to store in 'ids' (which is either vlan->uc or vlan->mc). This would WARN_ON_ONCE and then record a bogus filter ID of 0x1fff, neither of which is a good thing. Fixes: 0ccb998b ("sfc: fix filter_id misinterpretation in edge case") Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 6月, 2017 1 次提交
-
-
由 Martin Habets 提交于
The 8000 series adapters uses catch-all filters for encapsulated traffic to support filtering VXLAN, NVGRE and GENEVE traffic. This new filter functionality requires a longer MCDI command. This patch increases the size of buffers on stack that were missed, which fixes a kernel panic from the stack protector. Fixes: 9b410801 ("sfc: insert catch-all filters for encapsulated traffic") Signed-off-by: NMartin Habets <mhabets@solarflare.com> Acked-by: NEdward Cree <ecree@solarflare.com> Acked-by: Bert Kenward bkenward@solarflare.com Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 22 5月, 2017 1 次提交
-
-
由 Miroslav Lichvar 提交于
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid filter and update drivers which can timestamp all packets, or which explicitly list unsupported filters instead of using a default case, to handle the filter. CC: Richard Cochran <richardcochran@gmail.com> CC: Willem de Bruijn <willemb@google.com> Signed-off-by: NMiroslav Lichvar <mlichvar@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 06 4月, 2017 1 次提交
-
-
由 Edward Cree 提交于
If the mc_list is longer than 256 addresses, we enter mc_promisc mode. If we're in mc_promisc mode and the firmware doesn't support cascaded multicast, normally we also insert our mc_list, to prevent stealing by another VI. However, if the mc_list was too long, this isn't really helpful - the MC groups that didn't fit in the list can still get stolen, and having only some of them stealable will probably cause more confusing behaviour than having them all stealable. Since inserting 256 multicast filters takes a long time and can lead to MCDI state machine timeouts, just skip the mc_list insert in this overflow condition. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 3月, 2017 2 次提交
-
-
由 Edward Cree 提交于
The value we read from the header is in network byte order, whereas EFX_POPULATE_QWORD_* takes values in host byte order (which it then converts to little-endian, as MCDI is little-endian). Fixes: e9117e50 ("sfc: Firmware-Assisted TSO version 2") Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
It confuses sparse, which thinks the size isn't constant. Let's achieve the same thing with a BUILD_BUG_ON, since we know which one should be bigger and don't expect them ever to change. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 2月, 2017 3 次提交
-
-
由 Peter Dunning 提交于
efx_start_all can return without initialising queues as a reset is pending. This means that when netif_device_attach is called, the kernel can start sending traffic without having an initialised TX queue to send to. This patch avoids this by not calling netif_device_attach if there is a pending reset. Fixes: e283546c ("sfc:On MCDI timeout, issue an FLR (and mark MCDI to fail-fast)") Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bert Kenward 提交于
If the hw doesn't think they exist, we should defer to its authority. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
On EF10, hardware filter IDs are 13 bits, but in some places we store 32-bit "full filter IDs" in which higher order bits encode the filter match-priority. This could cause a filter to have a full filter ID of 0xffff, which is also the value EFX_EF10_FILTER_ID_INVALID which we use in 16-bit "short" filter IDs (without match-priority bits). This would occur if the hardware filter ID was 0x1fff and the match-priority was 7. Unfortunately, some code that checks for EFX_EF10_FILTER_ID_INVALID can be called on full filter IDs, and will WARN_ON if this ever happens. So, since we have plenty of spare bits in the full filter ID, this patch shifts the priority bits left one bit when constructing the full filter IDs, ensuring that the 0x2000 bit of a full filter ID will always be 0 and thus no full filter ID can ever equal EFX_EF10_FILTER_ID_INVALID. This patch also replaces open-coded full<->short filter ID conversions with calls to functions, thus keeping the definition of the full filter ID format in one place. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 15 2月, 2017 1 次提交
-
-
由 Andrew Rybchenko 提交于
Add min_interrupt_mode specification per NIC type. It is a bit confusing because of "highest interrupt mode is less capable". Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 2月, 2017 1 次提交
-
-
由 Edward Cree 提交于
Fixes: a0ee3541 ("sfc: process RX event inner checksum flags") Reported-by: NColin Ian King <colin.king@canonical.com> Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 2月, 2017 3 次提交
-
-
由 Jon Cooper 提交于
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and GENEVE UDP ports. Also reset the port list to empty on driver load and on driver unload, with appropriate flag set on the unload case. These port numbers are used for RX inner checksum offload, and in future will also be used for TX inner checksum offload and encapsulated TSO. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
Set the csum_level for encapsulated packets where the encapsulation type, l3 class and l4 class are sets that need it. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
Add support for RX checksum offload of encapsulated packets. This essentially just means paying attention to the inner checksum flags in the RX event, and if *either* checksum flag indicates a fail then don't tell the kernel that checksum offload was successful. Also, count these checksum errors and export the counts to ethtool -S. Test the most common "good" case of RX events with a single bitmask instead of a series of ifs. Move the more specific error checking in to a separate function for clarity, and don't use unlikely() there since we know at least one of the bits is bad. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 2月, 2017 1 次提交
-
-
由 Dan Carpenter 提交于
This bug is harmless because it's just a sanity check and we always pass valid values for "encap_type" but the test is off by one. Fixes: 9b410801 ("sfc: insert catch-all filters for encapsulated traffic") Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com> Acked-by: NBert Kenward <bkenward@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 2月, 2017 1 次提交
-
-
由 Colin Ian King 提交于
encap_type should be checked to see if it is greater or equal to the size of array map to fix an off-by-one array size check. This fixes an array overrun read as detected by static analysis by CoverityScan, CID#1398883 ("Out-of-bounds-read") Fixes: 9b410801 ("sfc: insert catch-all filters for encapsulated traffic") Signed-off-by: NColin Ian King <colin.king@canonical.com> Acked-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 1月, 2017 3 次提交
-
-
由 Edward Cree 提交于
8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic based on inner fields, and when the NIC recognises such traffic, it does not match unencapsulated traffic filters any more. So add catch- all filters for encapsulated traffic on supporting platforms. Although recognition of VXLAN and GENEVE is based on UDP ports, and thus will not occur until the driver (on the primary PF) notifies the firmware of UDP ports to use, NVGRE will always be recognised, hence without this patch 8000 series adapters will drop all NVGRE traffic. Partly based on patches by Jon Cooper <jcooper@solarflare.com>. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
Rationalise several debug-or-warnings printks using netif_cond_dbg to make output more consistent. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jon Cooper 提交于
If the NIC is switched from full-featured to low-latency, encapsulated filters are no longer available, and this causes errors. This patch removes those filters from the filter table on restore. Also, if filters which are removed by the above, or which we fail to insert when restoring filters, were UC, MC or broadcast default filters, invalidate the corresponding vlan->default_filters entry. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 1月, 2017 1 次提交
-
-
由 Tomáš Pilař 提交于
PIO buffer allocation can fail for two valid reasons: - we've run out of them (results in -ENOSPC) - the NIC configuration doesn't support them (results in -EPERM) Since both these failures are expected netif_err is excessive. Signed-off-by: NBert Kenward <bkenward@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 1月, 2017 2 次提交
-
-
由 Edward Cree 提交于
Ensures that we report the key and indirection table the NIC is using, rather than (if setting them failed earlier) what we wanted it to use. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 1月, 2017 2 次提交
-
-
由 Edward Cree 提交于
The 8000 series SFC NICs have 4K PIO buffers, rather than the 2K of the 7000 series. Rather than having a hard-coded PIO buffer size (ER_DZ_TX_PIOBUF_SIZE), read it from the GET_CAPABILITIES_V2 MCDI response. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
If an option descriptor has been sent on a queue but not followed by a packet, there will have been no completion event, so the read and write counts won't match and we'll think we can't do PIO. This combines with the fact that we have two TX queues (for en/disable checksum offload), and that both must be empty for PIO to happen. This patch adds a separate "packet_write_count" that tracks the most recent write_count we expect to see a completion event for; this excludes option descriptors but _includes_ PIO descriptors (even though they look like option descriptors). This is then used, rather than write_count, in efx_nic_tx_is_empty(). We only bother to maintain packet_write_count on EF10, since on Siena (a) there are no option descriptors and it always equals write_count, and (b) there's no PIO, so we don't need it anyway. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 1月, 2017 2 次提交
-
-
由 Bert Kenward 提交于
Setting dev_port changes the device names allocated by systemd. Any devices with a dev_port >0 will (in default distro configurations) have a suffix of "d<port-number>" appended. This is not something done by other drivers, and causes confusion for users. Fixes: 8be41320 ("sfc: Add code to export port_num in netdev->dev_port") Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bert Kenward 提交于
There's no good reason why this should be an SRIOV-only thing. Thus, also move it out of SRIOV-specific files. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 1月, 2017 1 次提交
-
-
由 Edward Cree 提交于
If we failed to set up RSS on EF10 (e.g. because firmware declared RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report no fields, rather than confusingly reporting what fields we _would_ be hashing on if RSS was working. Fixes: dcb4123c ("sfc: disable RSS when unsupported") Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2016 1 次提交
-
-
由 Edward Cree 提交于
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should only be used if it is not possible to continue without potential harm; and since the non-DEBUG driver will continue regardless (as the BUG_ON is compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver. So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID or the newly defined EFX_WARN_ON_ONCE_PARANOID. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 11月, 2016 3 次提交
-
-
由 Edward Cree 提交于
It gives no advantage over GSO now that xmit_more exists. If we find ourselves unable to handle a TSO skb (because our TXQ doesn't have a TSOv2 context and the NIC doesn't support TSOv1), hand it back to GSO. Also do that if the TSO handler fails with EINVAL for any other reason. As Falcon-architecture NICs don't support any firmware-assisted TSO, they no longer advertise TSO feature flags at all. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
If we fail to init the TXQ because of insufficient TSOv2 contexts, try again with TSOv2 disabled. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bert Kenward 提交于
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task of TCP segmentation to the firmware, such that we now just pass a single super-packet to the NIC. This means TSO has a great deal in common with a normal DMA transmit, apart from adding a couple of option descriptors. NIC-specific checks have been moved off the fast path and in to initialisation where possible. This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit and some error handling is now outside TSO, since it is common with other code. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 11月, 2016 2 次提交
-
-
由 Edward Cree 提交于
Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Edward Cree 提交于
This improves UDP spreading, and also slightly improves GRO performance of encapsulated TCP on 7000 series NICs. Signed-off-by: NEdward Cree <ecree@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-