When reconfiguring an interface due to a previous
hardware restart, mac80211 will currently include
the new IBSS flag on non-IBSS interfaces which may
confuse drivers.

Instead of doing the ~0 trick, simply spell out
which things are going to be reconfigured.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"mac80211: improve IBSS scanning" was missing a hunk.
This adds that hunk as originally intended.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When IBSS is fixed to a frequency, it can still
scan to try to find the right BSSID. This makes
sense if the BSSID isn't also fixed, but it need
not scan all channels -- just one is sufficient.
Make it do that by moving the scan setup code to
ieee80211_request_internal_scan() and include
a channel variable setting.

Note that this can be further improved to start
the IBSS right away if both frequency and BSSID
are fixed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This allows enabling TX and disabling both TX and
RX aggregation sessions manually in debugfs. It is
very useful for debugging session initiation and
teardown problems since with this you don't have
to force a lot of traffic to get aggregation and
thus have less data to analyse.

Also, to debug mac80211 code itself, make hwsim
"support" aggregation sessions. It will still just
transfer the frame, but go through the setup and
teardown handshakes.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Both of these functions can currently return
a station pointer that, to the driver, is
invalid (in IBSS mode only) because adding
the station failed. Check for that, and also
make ieee80211_find_sta() properly use the
per interface station search.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also remove associated IEEE80211_HW_NOISE_DBM from ieee80211_hw_flags.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My previous patch "mac80211: notify driver about
IBSS status" left a problem -- when we merge with
a new BSSID, we never tell the driver that we left
the old one. Fix that.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some drivers (e.g. iwlwifi) need to know and try
to figure it out based on other things, but making
it explicit is definitely better.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If AP do not provide us supported rates before assiociation, send
all rates we are supporting instead of empty information element.

v1 -> v2: Add comment.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use old supported rates, if AP do not provide supported rates
information element in a new managment frame.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently whenever rts thresold is set, every packet will use RTS
protection no matter its size exceeds the threshold or not. This is
due to a bug in the rts threshold check.
	if (len > tx->local->hw.wiphy->rts_threshold) {
		txrc.rts = rts = true;
	}
Basically it is comparing an int (len) and a u32 (rts_threshold),
and the variable len is assigned as:
	len = min_t(int, tx->skb->len + FCS_LEN,
			 tx->local->hw.wiphy->frag_threshold);
However, when frag_threshold is "-1", len is always "-1", which is
0xffffffff therefore rts is always set to true.

CC: stable@kernel.org
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that the mac80211 is choosing dynamic ps timeouts based on the ps-qos
network latency configuration, configure a default value of -1 as the dynamic
ps timeout in cfg80211. This value allows the mac80211 to determine the value
to be used.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Determine the dynamic PS timeout based on the configured ps-qos network
latency. For backwards wext compatibility, allow the dynamic PS timeout
configured by the cfg80211 to overrule the automatically determined value.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is used to configure APs to not bridge traffic between connected stations.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A misplaced interface type check bails out too early if the interface
is not in monitor mode. This patch moves it to the right place, so that
it only covers changes to the monitor flags.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta->last_tx_rate is traditionally updated just before transmitting a
frame based on information from the rate control algorithm. However, for
hardware drivers with IEEE80211_HW_HAS_RATE_CONTROL this is not performed,
as the rate control algorithm is not executed, and because the used rate is
not known before the frame has actually been transmitted.

This causes atleast a fixed 1Mb/s to be reported to user space. A few other
instances of code also rely on this information.

Fix this by setting the sta->last_tx_rate in tx_status handling. There, look
for last rates entry set by the driver, and use that as value for
sta->last_tx_rate.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When IEEE80211_HW_CONNECTION_MONITOR is configured by the driver, starting
of ieee80211_sta_conn_mon_timer should be prevented, as it is then not needed.

This is currently partially the case. As it seems, when a probe-response is
received from the AP the timer is still restarted, thus restarting the host
based connection keep-alive mechanism. These probe-responses happen at least
when scanning while associated.

Fix this by preventing starting of the ieee80211_sta_conn_mon_timer in the
ieee80211_rx_mgmt_probe_resp function.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds the survey function to both mac80211 itself and to mac80211_hwsim.
For the latter driver, we simply invent some noise level.A real driver which
cannot determine the real channel noise MUST NOT report any noise, especially
not a magically conjured one :-)
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When I set up multiple VAPs with ath9k, I encountered an issue that
the traffic may be lost after a while.

The detailed phenomenon is
1. After a while the clients connected to one of these VAPs will get
into a state that no broadcast/multicast packets can be transfered
successfully while the unicast packets can be transfered normally.
2. Minutes latter the unitcast packets transfer will fail as well,
because the ARP entry is expired and it can't be freshed due to the
broadcast trouble.

It's caused by the group key overwritten and someone discussed this
issue in ath9k-devel maillist before, but haven't work out a fix yet.

I referred the method in madwifi, and made a patch for ath9k.
The method is to set the high bit of the sender(AP)'s address, and
associated that mac and the group key. It requires the hardware
supports multicast frame key search. It seems true for AR9160.

Not sure whether it's the correct way to fix this issue. But it seems
to work in my test. The patch is attached, feel free to revise it.
Signed-off-by: NDaniel Yingqiang ma <yma.cool@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One HT debugging printk is missing a newline,
add it.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The sta_cleanup timer is used to periodically expire buffered frames from the
tx buf. The timer is executing periodically, regardless of the need for it.
This is wasting resources.

Fix this simply by not restarting the sta_cleanup timer if the tx buffer was
empty. Restart the timer when there is some more tx-traffic.

Cc: Janne Ylälehto <janne.ylalehto@nokia.com>
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Kalle reported that his system deadlocks since my
recent work in this area. The reason quickly became
apparent: we try to cancel_timer_sync() a timer
from within itself. Fix that by making the function
aware of the context it is called from.
Reported-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.

Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.

This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.

See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.

Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In a scenario, where a cfg80211 driver (station mode) does not send assoc request
and assoc response IEs in cfg80211_connect_result after a successful association
to an AP, cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE to the user space
application with NULL data. This can cause an issue at the event recipient.

An example of this is when cfg80211 sends IWEVASSOCREQIE and IWEVASSOCRESPIE
events with NULL event body to wpa_supplicant. The wpa_supplicant overwrites
the assoc request and assoc response IEs for this station with NULL data.
If the association is WPA/WPA2, the wpa_supplicant is not able to generate
EAPOL handshake messages, since the IEs are NULL.

With the patch, req_ie and resp_ie will be NULL by avoiding the
assignment if the driver has not sent the IEs to cfg80211. The event sending
code sends the events only if resp_ie and req_ie are not NULL. This
will ensure that the events are not sent with NULL event body.
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As scan_work is queued from work_work it needs to be checked if scan
has been started during execution of work_work. Otherwise, when hw
scan is used, the stack gets error about hw being busy with ongoing
scan. This causes the stack to abort scan without notifying the driver
about it. This leads to a situation where the hw is scanning and the stack
thinks it's not. Then when the scan finishes, the stack will complain by
warnings.
Signed-off-by: NTeemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We delay the skb linearising in ieee80211_rx_h_decrypt so that
frames do not require software decryption are not linearized. We
are safe to do this because ieee80211_get_mmie_keyidx() only
requires to touch nonlinear data for management frames, which are
already linearized before getting here.

Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enhance tracing by adding tracing for a variety of
callbacks that the drivers call, and also for
internal calls (currently limited to queue status).
This can aid debugging what is going on in mac80211
in interaction with drivers, since we can now see
what drivers call and not just what mac80211 calls
in the driver.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Grouped mesh action codes together with the other action codes in
ieee80211.h.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

WEP crypto was broken, but upon finding the problem
it is evident that other things were broken by the
paged RX patch as well.

To fix it, for now move the linearising in front.
This means that we linearise all frames, which is
not at all what we want, but at least it fixes the
problem for now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A few places in mac80211 do not currently acquire
the sta lock for RX aggregation, but they should.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The aggregation code has a number of quirks, like
inventing an unneeded WLAN_BACK_TIMER value and
leaking memory under certain circumstances during
station destruction. Fix these issues by using
the regular aggregation session teardown code and
blocking new aggregation sessions, all before the
station is really destructed.

As a side effect, this gets rid of the long code
block to destroy aggregation safely.

Additionally, rename tid_state_rx which can only
have the values IDLE and OPERATIONAL to
tid_active_rx to make it easier to understand
that there is no bitwise stuff going on on the
RX side -- the TX side remains because it needs
to keep track of the driver and peer states.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I want to use it during station destruction as well
so rename it to WLAN_STA_BLOCK_BA which is also the
only use of it now.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All callers of ieee80211_sta_stop_rx_ba_session can
just call __ieee80211_stop_rx_ba_session instead
because they already have the station struct, so do
that and remove ieee80211_sta_stop_rx_ba_session.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All other places except one in the TX path, which
has BHs disabled, and it also cannot be locked from
interrupts so disabling IRQs is not necessary.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When a station w/o a key is destroyed, or when
a driver submits work for a station and thereby
references it again, it seems like potentially
we could reference the station structure while
it is being destroyed.

Wait for an RCU grace period to elapse before
finishing destroying the station after we have
removed the station from the driver and from
the hash table etc., even in the case where no
key is associated with the station.

Also, there's no point in deleting the plink
timer here since it'll be properly deleted just
a bit later.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211 is quite strict on allowing authentication and association
commands only in certain states. In order to meet these requirements,
user space applications may need to clear authentication or
association state in some cases. Currently, this can be done with
deauth/disassoc command, but that ends up sending out Deauthentication
or Disassociation frame unnecessarily. Add a new nl80211 attribute to
allow this sending of the frame be skipped, but with all other
deauth/disassoc operations being completed.

Similar state change is also needed for IEEE 802.11r FT protocol in
the FT-over-DS case which does not use Authentication frame exchange
in a transition to another BSS. For this to work with cfg80211, an
authentication entry needs to be created for the target BSS without
sending out an Authentication frame. The nl80211 authentication
command can be used for this purpose, too, with the new attribute to
indicate that the command is only for changing local state. This
enables wpa_supplicant to complete FT-over-DS transition successfully.
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>