Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for tuners integrated to the IT9135 and IT9137.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is tuner driver for tuner integrated to the ITE IT9135 and
IT9137 chips. I split it out from the current it913x-fe driver.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

My 15c2:0036 device floods syslog when a keypad key is pressed:

	Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2
	Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fef2
	Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2
	Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2
	Feb 18 19:00:57 homeserver kernel: imon 5-1:1.0: imon_incoming_packet: unknown keypress, code 0x100fff2

This patch removes those messages from imon, following suggestion from
Mauro. Unknown keys shall be correctly handled by rc/input layer.
Signed-off-by: NKevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some imon devices (like 15c2:0036) need a higher delay between
send_packet calls.

Default value is still 5ms to avoid regressions on already working
hardware.

Also use interruptible wait to avoid load average going too high (and
let caller handle signals).
Signed-off-by: NKevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If no manager is connected to the vout device, the omapvid_init() function
fails. No error condition is checked, and the device is started. Later on,
when irq is serviced, a NULL pointer dereference occurs.
Also, the isr routine must be registered only if no error occurs, otherwise
the isr triggers without the proper setup, and the kernel oops again.
To prevent this, the error condition is checked, and the streamon function
exits with error. Also the isr registration call is moved after the setup
procedure is completed.
Reviewed-by: NPrabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I found very small bug in xc5000 source. When set option debug=1 and
listen a radio we see in dmesg xc5000: xc_SetTVStandard()
Standard = M/N-NTSC/PAL-BTSC at all times. However, it should be, instead
"FM Radio-INPUT1_MONO".

That happens because xc5000_set_radio_freq() gets the correct value for
VideoMode and AudioMode for radio and calls xc_SetTVStandard() where name
of standard comes from the incorrect place priv->video_standard.

This incorrect debug message makes debugging  a little difficult.
Signed-off-by: NDmitry Belimov <d.belimov@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Release v2.6.30 removed the MT9M001_PCA9536_SWITCH and
MT9V022_PCA9536_SWITCH Kconfig symbols, in commits
36034dc3 ("V4L/DVB (11032): mt9m001:
allow setting of bus width from board code") and
e958e27a ("V4L/DVB (11033): mt9v022:
allow setting of bus width from board code").
These two commits removed all gpio related code from these two drivers.
But they skipped removing their two selects of GPIO_PCA953X. Remove
these now as they are outdated. Their dependencies can never evaluate to
true anyhow.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

module_platform_driver_probe() eliminates the boilerplate and simplifies
the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

module_platform_driver_probe() eliminates the boilerplate and simplifies
the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

module_platform_driver_probe() eliminates the boilerplate and simplifies
the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the issue that appears when mt9v024 camera is used with the
mt9v022 soc camera driver. The minimum total row time is 690 columns
(horizontal width + horizontal blanking). The minimum horizontal
blanking is 61. Thus, when the window width is set below 627, horizontal blanking must
be increased. For the mt9v024 camera the values above are correct and
for the mt9v022 camera the correct values are in the existing kernel driver.
Signed-off-by: NAndrei Andreyanau <a.andreyanau@sam-solutions.net>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A recent commit "[media] soc-camera: Push probe-time power management to
drivers" causes an Oops during mt9m111 driver probing because its .ctx
private data field is now dereferenced before it is initialised. Fix this
by initialising the field earlier.
Reported-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Commit f9bd5843 changed V4L2_CID_EXPOSURE_AUTO
from boolean to enum, and commit af8425c5
changed the creation of this control into a menu for the mt9m111. However,
mt9m111_set_autoexposure() is still interpreting the value set for this control
as a boolean, which also conflicts with the default value of this control set to
V4L2_EXPOSURE_AUTO (0).
This patch makes mt9m111_set_autoexposure() interpret the value set for
V4L2_CID_EXPOSURE_AUTO as defined by enum v4l2_exposure_auto_type.
Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: NJavier Martin <javier.martin@vista-silicon.com>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The Kconfig entry for "TS2020 based tuners" defaults to modular if
DVB_FE_CUSTOMISE is set. But that Kconfig symbol was replaced with
MEDIA_SUBDRV_AUTOSELECT as of v3.7. So use the new symbol. And negate
the logic, so we are in line with all the similar entries in this file.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

add support for TVP514x as a media entity and support for
pad operations. The decoder supports 1 output pad.
The default format code was V4L2_MBUS_FMT_YUYV10_2X10
changed it to V4L2_MBUS_FMT_UYVY8_2X8.
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A lot of SOCs including Texas Instruments Davinci family mainly use
video decoders as input devices. This patch adds a flag
'MEDIA_ENT_T_V4L2_SUBDEV_DECODER' media entity type for decoder's.
Along side updates the documentation for this media entity type.
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The patch adds support for THS7353 video amplifier.
The the THS7353 amplifier is very much similar to the
existing THS7303 video amplifier driver.
This patch appropriately makes changes to the existing
ths7303 driver and adds support for the THS7353.
This patch also adds V4L2_IDENT_THS7353 for the THS7353
chip and appropriate changes to Kconfig file for building.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMartin Bugge <marbugge@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

module_platform_driver() eliminates the boilerplate and simplifies
the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use resource_size function on resource object instead of explicit
computation.
Signed-off-by: NAlexandru Gheorghiu <gheorghiuandru@gmail.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NIsmael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This prevents the kernel log from being spammed with these messages.
By turning on the debug option you will see them again.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some drivers have special memory requirements for their buffers, usually
related to DMA (e.g. GFP_DMA or __GFP_DMA32). Make it possible to specify
additional GFP flags for those buffers by adding a gfp_flags field to
vb2_queue.
Note that this field will be replaced in the future with a different
mechanism, but that is still work in progress and we need this feature
now so we won't be able to convert drivers with such requirements to vb2.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NFederico Vaga <federico.vaga@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The stats are cleared by the frontend. Don't do it at DTV_CLEAR.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The DVBv3 signal strength indicator is bogus: it doesn't range
from 0 to 65535 as it would be expected. Also, 0 means the max
signal strength.
Now that a better way to estimate it was added, use the new
way.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The AZ6007 driver released by Terratec has a better way to
estimate the signal strength, at CtrlSigStrength(). Port it
to the driver.
It should be noticed that there are two parameters there that
are tuner-specific.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The original az6007 driver has the code to calculate such
stats. Add it to the driver, reporting them via DVBv5
stats API.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The BER code does nothing but filling it with zero. Remove it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/common/siano/smsdvb-debugfs.c:51:6: warning: no previous prototype for 'smsdvb_print_dvb_stats' [-Wmissing-prototypes]
drivers/media/common/siano/smsdvb-debugfs.c:154:6: warning: no previous prototype for 'smsdvb_print_isdb_stats' [-Wmissing-prototypes]
drivers/media/common/siano/smsdvb-debugfs.c:244:6: warning: no previous prototype for 'smsdvb_print_isdb_stats_ex' [-Wmissing-prototypes]
drivers/media/common/siano/smscoreapi.c:832:5: warning: no previous prototype for 'smscore_configure_board' [-Wmissing-prototypes]
drivers/media/common/siano/smscoreapi.c:1301:5: warning: no previous prototype for 'smscore_init_device' [-Wmissing-prototypes]
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix all other remaining checkpatch.pl compliants on the Siano driver,
except for the 80-cols (soft) limit. Those are harder to fix, and
probably not worth to do right now.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove the remaining CamelCase checkpatch.pl compliants.
There are still a few left, but those are due to USB and
DVB APIs.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix the remaining checkpatch.pl compliants at smscoreapi.h,
except by the "line over 80 characters" on comments. Fixing those
would require more time, as the better is to convert them into the
struct descriptions used inside the kernel, as described at:
	Documentation/kernel-doc-nano-HOWTO.txt
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are several structures defined in uppercase. Convert them
to lowercase, and simplify their names, when possible.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It is almost impossible to see a compliant with checkpatch.pl
on those Siano drivers, as there are simply too much violations
on it. So, now that a big change was done, the better is to
cleanup the checkpatch compliants.

Let's first replace all CammelCase symbols found at smscoreapi.h
using camel_case namespace. That removed 144 checkpatch.pl
compliants on this file. Of course, the other files need to be
fixed accordingly.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This driver can use several firmwares. Provide such info at
module firmware metadata.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are too many firmwares there. As we need to add
MODULE_FIMWARE() macros, the better is to define their names
on just one place and use the macros for both cards/device type
tables and MODULE_FIRMWARE().
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>