CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.

With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move to circular buffers management macro and correct an error
with circular buffer initial condition.

Without this patch, the macb_tx_ring_avail() function was
not reporting the proper ring availability at startup:
macb macb: eth0: BUG! Tx Ring full when queue awake!
macb macb: eth0: tx_head = 0, tx_tail = 0
And hanginig forever...

I remove the macb_tx_ring_avail() function and use the
proven macros from circ_buf.h. CIRC_CNT() is used in the
"consumer" part of the driver: macb_tx_interrupt() to match
advice from Documentation/circular-buffers.txt.
Reported-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only the first register set is used for matching but
we support getting the initial hw addr from any of
the registers.

To prevent stale entries and false matches clear unused
register sets. This most important for the at91_ether
driver where u-boot always uses the 2nd register set.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

for usage in at91_ether driver.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is used on one AT91RM9200 board where a bootloader stores
the Ethernet address in the wrong order.

Support this on macb so address setting functions can be shared
with the at91_ether driver.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macb driver in u-boot uses the first register set while
the at91_ether driver in u-boot uses the second register set.

By checking all register set, like at91_ether does, this code
can be shared between the drivers.

This only changes behavior on macb if no vaild address
is found in the first register set.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

When underlying phy driver restores its state very fast after being brought
down and up so that macb driver function macb_handle_link_change() was never
called with link state "down", driver's internal representation of phy speed
and duplex (bp->speed and bp->duplex) didn't change. So, macb driver sees no
reason to perform actual write to the NCFGR register, although the speed and
duplex settings in that register were reset when interface was brought down
and up. In that case actual phy speed and duplex differ from NCFGR settings.
The patch fixes that by keeping internal driver representation of speed and
duplex in sync with actual content of NCFGR.
Signed-off-by: NVitalii Demianets <vitas@nppfactor.kiev.ua>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If no pinctrl available just report a warning as some architecture may not
need to do anything.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: adapt the error path, remove unneeded headers]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the ethernet frame payload word-aligned, possibly making the
memcpy into the skb a bit faster. This will be even more important
after we eliminate the copy altogether.

Also eliminate the redundant RX_OFFSET constant -- it has the same
definition and purpose as NET_IP_ALIGN.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle all TX errors, not only underruns. TX error management is
deferred to a dedicated workqueue.
Reinitialize the TX ring after treating all remaining frames, and
restart the controller when everything has been cleaned up properly.
Napi is not stopped during this task as the driver only handles
napi for RX for now.
With this sequence, we do not need a special check during the xmit
method as the packets will be caught by TX disable during workqueue
execution.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add macb_get_regs() ethtool function and its helper function:
macb_get_regs_len().
The version field is deduced from the IP revision which gives the
"MACB or GEM" information. An additional version field is reserved.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of masking head and tail every time we increment them, just let them
wrap through UINT_MAX and mask them when subscripting. Add simple accessor
functions to do the subscripting properly to minimize the chances of messing
this up.

This makes the code slightly smaller, and hopefully faster as well.  Also,
doing the ring buffer management this way will simplify things a lot when
making the ring sizes configurable in the future.

Available number of descriptors in ring buffer function by David Laight.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, adapt to newer kernel]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some revision of GEM, TSR status register has more information.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function has little meaning so remove it altogether and
let ethtool core fill in the fields automatically.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NBen Hutchings <bhutchings@solarflare.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert some noisy netdev_dbg() statements to netdev_vdbg(). Defining
DEBUG will no longer fill up the logs; VERBOSE_DEBUG still does.
Add one more verbose debug for ISR status.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics, add ISR status]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove a couple of unneeded barriers and document the remaining ones.
Signed-off-by: NHavard Skinnemoen <havard@skinnemoen.net>
[nicolas.ferre@atmel.com: split patch in topics]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Gigabit Ethernet mode to GEM cadence IP and enable RGMII connection.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following build failure on S390:
  In file included from drivers/net/ethernet/cadence/at91_ether.c:35:0:
   drivers/net/ethernet/cadence/macb.h: In function 'macb_is_gem':
   drivers/net/ethernet/cadence/macb.h:563:2: error: implicit declaration of function '__raw_readl' [-Werror=implicit-function-declaration]
   drivers/net/ethernet/cadence/at91_ether.c: In function 'update_mac_address':
   drivers/net/ethernet/cadence/at91_ether.c:119:2: error: implicit declaration of function '__raw_writel' [-Werror=implicit-function-declaration]
   cc1: some warnings being treated as errors
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This will allow us to remove the last mach include from at91_ether
and also make it easier to share address setup with macb.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that HAVE_NET_MACB is gone let's just select MACB to
satisfy the dependecies in at91_ether.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

macb is a platform driver and there is nothing that prevents
this driver from being built on non-ARM/AVR32 platforms.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When building macb on x86_64 the following warnings show up:
  drivers/net/ethernet/cadence/macb.c: In function macb_interrupt:
  drivers/net/ethernet/cadence/macb.c:556:4: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c: In function macb_reset_hw:
  drivers/net/ethernet/cadence/macb.c:792:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:793:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
  drivers/net/ethernet/cadence/macb.c:796:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]

Use -1 insted of ~0UL, as done in other places in the driver,
to silence these warnings.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

This patch does two things:
* Use macb struct members and remove at91_ether ones
* Alloc DMA buffers on netdev start and dealloc on stop
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

This rips out the at91_ether phy handling and ethtool stuff
and replace it with equivalent stuff from macb.

The only thing lost is the phy irq support from at91_ether,
but this can be added to macb and then benefit all users.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

Comile macb as well as at91_ether to access exported functions.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>

Export some symbols to start sharing code between
macb and at91_ether drivers.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>