Add a schema validator to nxp,sja1105.yaml and to dsa.yaml for explicit
MAC-level RGMII delays. These properties must be per port and must be
present only for a phy-mode that represents RGMII.

We tell dsa.yaml that these port properties might be present, we also
define their valid values for SJA1105. We create a common definition for
the RX and TX valid range, since it's quite a mouthful.

We also modify the example to include the explicit RGMII delay properties.
On the fixed-link ports (in the example, port 4), having these explicit
delays is actually mandatory, since with the new behavior, the driver
shouts that it is interpreting what delays to apply based on phy-mode.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since a switch is basically a bunch of Ethernet controllers, just
inherit the common schema for one to get stronger type validation of the
properties of a port.

For example, before this change it was valid to have a phy-mode = "xfi"
even if "xfi" is not part of ethernet-controller.yaml, now it is not.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All ports require either a phy-handle or a fixed-link, and port 3 in the
example didn't have one. Add it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net: sched: fixes after recent qdisc->running changes

First patch fixes a plain bug in qdisc_run_begin().
Second patch removes a pair of atomic operations, increasing performance.
====================

Link: https://lore.kernel.org/r/20211019003402.2110017-1-eric.dumazet@gmail.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

__QDISC_STATE_RUNNING is only set/cleared from contexts owning qdisc lock.

Thus we can use less expensive bit operations, as we were doing
before commit f9eb8aea ("net_sched: transform qdisc running bit into a seqcount")

Fixes: 29cbcd85 ("net: sched: Remove Qdisc::running sequence counter")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: NToke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

For non TCQ_F_NOLOCK qdisc, qdisc_run_begin() tries to set
__QDISC_STATE_RUNNING and should return true if the bit was not set.

test_and_set_bit() returns old bit value, therefore we need to invert.

Fixes: 29cbcd85 ("net: sched: Remove Qdisc::running sequence counter")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Ahmed S. Darwish <a.darwish@linutronix.de>
Tested-by: NIdo Schimmel <idosch@nvidia.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: NToke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Replacing dma_pool_alloc/memset() with dma_pool_zalloc()
to simplify the code.
Signed-off-by: NCai Huoqing <caihuoqing@baidu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.

Remove the redundant 'flush_workqueue()' calls.

This was generated with coccinelle:

@@
expression E;
@@
- 	flush_workqueue(E);
	destroy_workqueue(E);
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PCI core code in the pci_call_probe() has a path that doesn't hold
device_lock. It happens because the ->probe() is called through the
workqueue mechanism.

   349 static int pci_call_probe(struct pci_driver *drv, struct pci_dev *dev,
   350                           const struct pci_device_id *id)
   351 {
   352
....
   377         if (cpu < nr_cpu_ids)
   378                 error = work_on_cpu(cpu, local_pci_probe, &ddi);

Luckily enough, the core still ensures that only single flow is executed,
so it safe to remove the assert checks that anyway were added for annotations
purposes.

Fixes: b88f7b12 ("devlink: Annotate devlink API calls")
Reported-by: NAmit Cohen <amcohen@nvidia.com>
Signed-off-by: NLeon Romanovsky <leonro@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable will be assigned again later in the if condition,
there is no meaning there.

drivers/net/ethernet/broadcom/tg3.c:5750:2 warning:

Value stored to 'current_link_up' is never read.
Reported-by: NZeal Robot <zealci@zte.com.cn>
Signed-off-by: Nluo penghao <luo.penghao@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.

Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.

Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.

Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: NRobert Hancock <robert.hancock@calian.com>
Signed-off-by: NRussell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric reported that the rate estimator reads statics from the softirq
which in turn triggers a warning introduced in the statistics rework.

The warning is too cautious. The updates happen in the softirq context
so reads from softirq are fine since the writes can not be preempted.
The updates/writes happen during qdisc_run() which ensures one writer
and the softirq context.
The remaining bad context for reading statistics remains in hard-IRQ
because it may preempt a writer.

Fixes: 29cbcd85 ("net: sched: Remove Qdisc::running sequence counter")
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit ea269a6f ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.

Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.

The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.

We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This assignment statement is meaningless, because the statement
will execute to the tag "set_itr_now".

The clang_analyzer complains as follows:

drivers/net/ethernet/intel/e1000e/netdev.c:2552:3 warning:

Value stored to 'current_itr' is never read.
Reported-by: NZeal Robot <zealci@zte.com.cn>
Signed-off-by: Nluo penghao <luo.penghao@zte.com.cn>
Reviewed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
ethernet: add eth_hw_addr_gen() for switches

While doing the last polishing of the drivers/ethernet
changes I realized we have a handful of drivers offsetting
some base MAC addr by an id. So I decided to add a helper
for it. The helper takes care of wrapping which is probably
not 100% necessary but seems like a good idea. And it saves
driver side LoC (the diffstat is actually negative if we
compare against the changes I'd have to make if I was to
convert all these drivers to not operate directly on
netdev->dev_addr).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Vadym and Taras report that the current behavior of the driver
is not exactly expected and it's better to add the port id in
like other drivers do.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have 5 drivers which offset base MAC addr by port id.
Create a helper for them.

This helper takes care of overflows, which some drivers
did not do, please complain if that's going to break
anything!
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NShannon Nelson <snelson@pensando.io>
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
ethernet: manual netdev->dev_addr conversions (part 2)

Manual conversions of Ethernet drivers writing directly
to netdev->dev_addr (part 2 out of 3).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Invert the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Read the address into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Multi-level qdisc offload

Petr says:

Currently, mlxsw admits for offload a suitable root qdisc, and its
children. Thus up to two levels of hierarchy are offloaded. Often, this is
enough: one can configure TCs with RED and TCs with a shaper on, and can
even see counters for each TC by looking at a qdisc at a sufficiently
shallow position.

While simple, the system has obvious shortcomings. It is not possible to
configure both RED and shaping on one TC. It is not possible to place a
PRIO below root TBF, which would then be offloaded as port shaper. FIFOs
are only offloaded at root or directly below, which is confusing to users,
because RED and TBF of course have their own FIFO.

This patch set lifts assumptions that prevent offloading multi-level qdisc
trees.

In patch #1, offload of a graft operation is added to TBF. Grafts are
issued as another qdisc is linked to the qdisc in question, and give
drivers a chance to react to the linking. The absence of this event was not
a major issue so far, because TBF was not considered classful, which
changes with this patchset.

The codebase currently assumes that ETS and PRIO are the only classful
qdiscs. The following patches gradually lift this assumption.

In patch #2, calculation of traffic class and priomap of a qdisc is fixed.

Patch #3 fixes handling of future FIFOs. Child FIFO qdiscs may be created
and notified before their parent qdisc exists and therefore need special
handling.

Patches #4, #5 and #6 unify, respectively, child destruction, child
grafting, and cleanup of statistics.

Patch #7 adds a function that validates whether a given qdisc topology is
offloadable.

Finally in patch #8, TBF and RED become classful. At this point, FIFO
qdiscs grafted to an offloaded qdisc should always be offloaded.

Patch #9 adds a selftest to verify some offloadable and unoffloadable qdisc
trees.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This checks that various qdisc configurations either are or are not
offloaded.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Permit offloading qdiscs below RED and TBF. In order to avoid having to
implement trivial propagating callbacks for get_prio_bitmap and
get_tclass_num, extend mlxsw_sp_qdisc_get_prio_bitmap() and
..._get_tclass_num() to handle the lack of the callback as a cue to forward
the request to the parent.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A following patch will enable offloading qdiscs that are deeper than
directly under root qdisc. Currently the topology validation consists of
demanding a root qdisc position for ETS and PRIO. Since RED and TBF are
considered classless, this is enough. In order to prevent some nonsensical
combinations when RED and TBF become classful, introduce a more general
topology validator.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Spectrum, there are no per-TC TX counters. Instead, mlxsw uses per-prio
counters and aggregates them according to the priomap. Therefore when
priomap changes, the counter base values need to be reset to reflect the
change. Previously, this was only done for the sole child qdisc, but a
following patch makes RED and TBF classful. Thus apply the request to the
whole sub-tree.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Qdisc graft operations have so far been reported at PRIO, ETS and RED, with
RED events ignored, because RED was not considered a classful qdisc. A
following patch will make mlxsw recognize RED and TBF as classful qdiscs,
and thus it is necessary to validate grafting at these qdiscs as well.
Rename the existing graft validator to make it clear that it is a generic
function, and invoke for RED and TBF graft events as well. Drop the
unnecessary PRIO helper and invoke the graft validator directly for PRIO as
well.
Signed-off-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>