Signed-off-by: NEdwin van Vliet <edwin@cheatah.nl>
Reviewed-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Due to timing, it is possible for the LOS and DFE to remain on. This
is due to the link progressing to LinkUP prior to the driver getting
the first Status Changed interrupt.  By expanding the conditions under
which LOS is turned off and DFE timeout is being set, timing is no
longer an issue.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

The time limit test now correctly checks against current jiffies to
avoid the hang.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

These changes were incorrectly fixed by codespell. They were now
manually corrected.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

For active and far-EQ cables use an LE2 value of 0 for improved SI.
Signed-off-by: NMitko Haralanov <mitko@qlogic.com>
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Hold the IB link at DISABLED until we get the correct TX settings
on mezz boards.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

* ib_wq is added, which is used as the common workqueue for infiniband
  instead of the system workqueue.  All system workqueue usages
  including flush_scheduled_work() callers are converted to use and
  flush ib_wq.

* cancel_delayed_work() + flush_scheduled_work() converted to
  cancel_delayed_work_sync().

* qib_wq is removed and ib_wq is used instead.

This is to prepare for deprecation of flush_scheduled_work().
Signed-off-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Improve the QMH SERDES tunning on initial driver load by having the
driver go through a link state change.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The basic idea is that on SusieQ, the difficult part of mapping QPN to
context is handled by the mapping registers so the generic QPN
allocation doesn't need to worry about chip specifics.  For Monty and
Linda, there is no mapping table so the qpt->mask (same as
dd->qpn_mask), is used to see if the QPN to context falls within
[zero..dd->n_krcv_queues).
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

For SusieQ we need to write to the interrupt timer register before
updating the header queue head with interrupt count.  This is to
ensure that the timer is enabled properly and a receive available
interrupt is delivered.  Otherwise this interrupt can be lost if the
receiver header/eager queues are full before the timer is enabled.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add new SERDES tuning to aid manufacturing.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add support to recognize another board variation named QME7362.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The receive header queue sizes need to modified for performance
tuning.  Three module parameters are added to support this.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This is required for hardware testing.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Up to now, we have set the number of available user contexts based on
the number of hardware contexts which is set according to the number
of available CPUs.  This was fine since most CPUs had a power of two
number of cores and the chip supported 4, 8, or 16 user contexts.  Now
that some systems have 12 cores, the default isn't optimal and should
be set to 12 even though 16 hardware contexts need to be enabled.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Turn off IB latency mode. This improves link quality for slower
process chips.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The HCA checks for certain hardware errors which can be falsely
triggered when the IB link is reset. The fix is to mask them rather
than report them.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Don't set write combining via PAT on the VL15 buffers to avoid a rare
problem with unaligned writes from interrupt-flushed store buffers.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The DCA code was left over from internal development to test the
hardware feature and allow performance testing.  The results were
mixed and will require some additional work to make full use of the
feature.  Therefore, it is being removed for now.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

As part of the earlier patches submitted and reviewed, it was agreed
to change the way serdes tuning parameters were specified to the
driver.  The updated patch got dropped by the linux-rdma email list so
the earlier version of qib_iba7322.c ended up being used.  This patch
updates qib_iab7322.c to the simpler, single parameter method of
setting the serdes parameters.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Add a low-level IB driver for QLogic PCIe adapters.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>