Compile error reported by Jim Davis on netdev.

ip6_sk_accept_pmtu() needs net/ip6_route.h
Signed-off-by: NScott Feldman <sfeldma@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hauke Mehrtens says:

====================
b44: add support for external PHY

This adds support for an external phy connected to the mac controlled
by b44. This is used on home routers of the BCM47xx line where this MAC
core was used and is contended to an external switch core through MII.
These patches are in OpenWrt for some time and are tested by different
users with different devices.

The publicly available Programmer's Reference Guide for some of these
chips help making this patch it would be nice to have such a
documentation for more Broadcom Chips like some SoCs.
https://www.broadcom.com/collateral/pg/440X-PG02-R.pdf
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>

The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

b44_phy_reset() will fail for an external PHY and only work with the
internal PHY, this was an old workaround when the detection of an
external switch based on the PHY address failed and it is not needed
any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this patch we can not access the PHY when the MAC is switched
off. This PHY access is needed to configure the switch, which is done
through PHY registers.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the older home routers based on the Broadcom BCM47XX SoC series
are using a MAC that is supported by b44. On most of these routers not
the internal PHY of this MAC core is used, but a switch sometimes on an
external chip or integrated into the same SoC as the Ethernet core.
For this switch a special PHY driver is needed which should not be
integrated into b44 as the same switches are also used by other
Broadcom home networking SoCs which are using different Ethernet MAC
drivers. This was tested with the b53 switch driver which is currently
on its way to mainline.

If the internal PHY is not used, b44 will now search on the MDIO bus
for a phy and use the Linux phylib subsystem to register a driver.
Support for the internal PHY must stay here, because there are some
device which are suing the internal phy.

With this patch we scan the mdio bus when the sprom or nvram says that
the PHY address is 30, if a PHY was found at this address b44 uses it.

This was tested with a BCM4704, BCM4712 and BCM5354.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next patch will add these functions for phylib, and we should
rename the old ones before. This now indicates that these functions are
used for the mdio registers and on the mii interface.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the phy address is 31, this means that there is no PHY connected
to this MAC at all, no internal and no external PHY. Reading these PHY
registers causes a system reset on some routers.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY address 30 means there is no local PHY, but there could be an
external PHY like a switch connected via MII. This is the case on most
embedded home routers where this driver is used.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ethernet core supported by b44 supports an internal PHY integrated
into the mac core, which is supported by the b44 driver and an external
PHY to which the mac core is connected. This external PHY could be a
switch connected through MII, which is often the case when this core is
used on home routers. The usage of an external PHY was assumed when the
PHY address 30 was used and an internal PHY was assumed when the PHY
address was different. To verify that b44_phy_reset() was called and
checked if it worked, otherwise PHY address 30 was assumed, an external
PHY. It is better to check the register which says which PHY is
connected to the MAC instead of checking the PHY address.
The interface to an external PHY was only activated when this register
was set.

This also changes B44_FLAG_INTERNAL_PHY to B44_FLAG_EXTERNAL_PHY, it is
easier to check.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Willem noticed a TCP_RR regression caused by TCP autocorking
on a Mellanox test bed. MLX4_EN_TX_COAL_TIME is 16 us, which can be
right above RTT between hosts.

We can receive a ACK for a packet still in NIC TX ring buffer or in a
softnet completion queue.

Fix this by always pushing the skb if it is at the head of write queue.

Also, as TX completion is lockless, it's safer to perform sk_wmem_alloc
test after setting TSQ_THROTTLED.

erd:~# MIB="MIN_LATENCY,MEAN_LATENCY,MAX_LATENCY,P99_LATENCY,STDDEV_LATENCY"
erd:~#  ./netperf -H remote -t TCP_RR -- -o $MIB | tail -n 1
(repeat 3 times)

Before patch :

18,1049.87,41004,39631,6295.47
17,239.52,40804,48,2912.79
18,348.40,40877,54,3573.39

After patch :

18,22.84,4606,38,16.39
17,21.56,2871,36,13.51
17,22.46,2705,37,11.83
Reported-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: f54b3111 ("tcp: auto corking")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_for_each_entry(a, &act_base, head) doesn't
exit with a = NULL if we reached the end of the list.

tcf_unregister_action(), tc_lookup_action_n() and tc_lookup_action()
need fixes.

Remove tc_lookup_action_id() as its unused and not worth 'fixing'
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 1f747c26 ("net_sched: convert tc_action_ops to use struct list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_for_each_entry(t, &tcf_proto_base, head) doesn't
exit with t = NULL if we reached the end of the list.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 36272874 ("net_sched: convert tcf_proto_ops to use struct
list_head")
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes:
1) pass mask rather than size to tcf_hashinfo_init()
2) the cleanup should be in reversed order in mirred_cleanup_module()
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Fixes: 369ba567 ("net_sched: init struct tcf_hashinfo at register time")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tan Xiaojun says:

====================
bridge: cleanup and fix checkpatch errors

Clean up and fix some checkpatch errors in bridge driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>

That open brace { should be on the previous line.
Signed-off-by: NTan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"foo * bar" should be "foo *bar".
Signed-off-by: NTan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Spaces required before the open parenthesis '(', before the open
brace '{', after that ',' and around that '?/:'.
Signed-off-by: NTan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return is not a function, parentheses are not required.
Signed-off-by: NTan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Because err is always negative, remove unnecessary condition
judgment.
Signed-off-by: NTan Xiaojun <tanxiaojun@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Save pkt_hash_types in tpa structure.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sergei Shtylyov says:

====================
Add PHY IRQ support to the 'sh_eth' driver

   This patchset adds support for passing PHY's IRQ to the 'sh_eth' driver from
the platform code and removes now useless code that hinders the PHY IRQ handing
by philib.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's no need anymore to call phy_init_hw() to reset/resume the PHY from the
driver, as the call chain in phylib already has reached it, and so reset/resumed
the PHY (even resuming it twice). This duplicate reset is not only  needless, it
e.g. clears the PHY's interrupt enables just setup by phylib and so prevents the
expected IRQs from the PHY.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the platform code to pass PHY's IRQ to the driver.  Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amir Vadai says:

====================
net/mlx4: Mellanox driver update 08-12-2013

This patchset contains:
1. Support in ndo_get_phys_port_id added by Hadar.
2. Change the driver to use by default CQE/EQE size of 64 bytes done by Eyal.
   This doubles the packet-rate  of the NIC.
3. Configure the XPS queue mapping on driver load - added by Ido.
4. Fixes for some small bugs done by Jenny and Matan

Patchset was applied and tested against commit: "23721754 lib: hash: follow-up
fixups for arch hash"

Changes from V1:
- Removed Patch 10 "net/mlx4_en: Fix Supported/Advertised link mode reported by
  ethtool". This patch is needed to be rewritten from scratch and I wouldn't
  like it to block the rest of the patches in this set.
  Also, fix to Kconfig suggested by Ben will be sent in next patchset.

Changes from V0:
- Found some issues in "Reuse memory in RX flow" patch from V0.
  Removing this patch from the patchset till analyzed and fixed.
- Fix some coding style issues in patch 6 "Configure the XPS queue mapping on
  driver load"
- Changed patch 9 "Add NAPI support for transmit side" to use NAPI_POLL_WEIGHT
  instead of MLX4_EN_TX_BUDGET
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MLX4_DEV_EVENT_SLAVE_INIT and MLX4_DEV_EVENT_SLAVE_SHUTDOWN
events used by Hypervisor to inform the PPF IB driver that
IB para-virtualization must be initialized/destroyed for a slave.
If this event is catched by ETH VF annoying but harmless error message
is printed into dmesg. Remove dmesg prints for these events.
Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To achieve out of the box performance default is to use 64 byte CQE/EQE.
In tests that we conduct in our labs, we achieved a performance
improvement of twice the message rate. For older VF/libmlx4 support,
enable_64b_cqe_eqe must be set to 0 (disabled).
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the port GUID read from the firmware to identify the physical port.
This port identifier is available via ndo_get_phys_port_id for both PF
and VF net-devices.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use correct names for QUERY_FUNC_CAP fields: flags0 and flags1.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All mailboxes are already zeroed by commit:
571b8b92 net/mlx4_core: Initialize all mailbox buffers to zero before use
Remove explicit zero set for force mac and force vlan fields in
mlx4_QUERY_FUNC_CAP_wrapper
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Given we allocate memory for each cpu, we can do this
using NUMA affinities, instead of using NUMA policies
of the process changing flow_limit_cpu_bitmap value.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch marks the function il_clear_traffic_stats() in debug.c as
static because they are not used outside this file.

Thus, it also removes the following warnings in
wireless/iwlegacy/debug.c:

drivers/net/wireless/iwlegacy/debug.c:35:1: warning: no previous prototype for ‘il_clear_traffic_stats’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch marks the function il4965_ucode_rx_stats_read(),
il4965_ucode_tx_stats_read() and il4965_ucode_general_stats_read() in
4965-debug.c as static because they are not used outside this file.

Thus, it also removes the following warnings in
wireless/iwlegacy/4965-debug.c:

drivers/net/wireless/iwlegacy/4965-debug.c:59:1: warning: no previous prototype for ‘il4965_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:471:1: warning: no previous prototype for ‘il4965_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/4965-debug.c:637:1: warning: no previous prototype for ‘il4965_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch marks the function il3945_ucode_rx_stats_read(),
il3945_ucode_tx_stats_read() and il3945_ucode_general_stats_read() in
3945-debug.c as static because they are not used outside this file.

Thus, it also removes the following warnings in
wireless/iwlegacy/3945-debug.c:

drivers/net/wireless/iwlegacy/3945-debug.c:52:1: warning: no previous prototype for ‘il3945_ucode_rx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:317:1: warning: no previous prototype for ‘il3945_ucode_tx_stats_read’ [-Wmissing-prototypes]
drivers/net/wireless/iwlegacy/3945-debug.c:407:1: warning: no previous prototype for ‘il3945_ucode_general_stats_read’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a new header file include/net/Space.h which contains
prototype declaration of sbni_probe().

Include the new header file in drivers/net/Space.c and
drivers/net/wan/sbni.c because they use this function.

This eliminates the following warning in wan/sbni.c:
drivers/net/wan/sbni.c:224:12: warning: no previous prototype for ‘sbni_probe’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>