The AHCI controller found in the STA2X11 chip uses BAR number 0
instead of 5. Also, the chip's fixup code sets a special DMA mask
for all of its PCI functions, and the mask must be preserved here.
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The author of this driver clearly wasn't familiar with the BMIDE specification
(also known as SFF-8038i) when he implemented the bmdma_status() method: first,
the interrupt bit of the BMIDE status register corresponds to nothing else but
INTRQ signal (ATAPI_DEV_INT here); second, the error bit is only set if the
controller encounters issue doing the bus master transfers, not on the IDE DMA
burst termination interrupts like here (moreover, setting the error bit doesn't
cause an interrupt).  We now need to disable all those unused interrupts...

(The only thing I couldn't figure out is how to flush the FIFO to memory once
the interrupt happens as required by the mentioned spec.)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The ata port is brought back to full power state during system resume.
So its runtime PM status will have to be updated to reflect
the actual post-system sleep status.

This also fixes below warning during system suspend/resume.

WARNING: at /work/linux/drivers/ata/libata-eh.c:4034
ata_scsi_port_error_handler+0x89/0x557()

4034         WARN_ON(!(ap->pflags & ATA_PFLAG_SUSPENDED));
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add platform hooks for custom suspend() and resume() functions. The
generic suspend/resume code in drivers/ata/ahci_platform.c is adapted
from the PCI version in drivers/ata/ahci.c.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Commit b3a70601 (libata: Add a
drivers/ide style DMA disable) neglected to remove the line in
ata_do_set_mode() it has obviously made useless/duplicated.  Do this
now, and make a line added back then wrapped properly...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

CONFIG_OF_IRQ is not available on some platforms and using of_irq_*
breaks the build. Since resources are already populated in the platform
device, get the irq from there instead.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch converts the drivers in drivers/ata/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.

Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Munaut <tnt@246tNt.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Mark Miesfeld <mmiesfeld@amcc.com>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* Fix cable detection to also account for the slave device cable bit.

* Disable UDMA when programming MWDMA in cs5536_set_dmamode().

* Don't change UDMA settings in cs5536_set_piomode().

* Add cs5536_program_dtc() helper.

* Cleanup and uninline cs5536_[read,write]() methods.

Cc: Martin K. Petersen <mkp@mkp.net>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

atapi_pio_bytes() uses bare numbers for the ATAPI interrupt reason bits despite
these are #define'd in <linux/ata.h>.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add ata port runtime suspend/resume/idle callbacks.
Set ->eh_noresume to skip the runtime PM calls on scsi host
in the error handler to avoid dead lock.
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Change ata_host_request_pm to ata_port_request_pm which performs
port suspend/resume.

Add ata port type driver which implements port PM callbacks.
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Currently, the device tree of ata port and scsi host looks as below,

        /sys/devices/pci0000:00/0000:00:1f.2    (ahci controller)
        |-- ata1                                (ata port)
        |-- host0                               (scsi host)
           |-- target0:0:0                      (scsi target)
               |-- 0:0:0:0                      (disk)

This patch makes ata port as parent device of scsi host, then it becomes

        /sys/devices/pci0000:00/0000:00:1f.2    (ahci controller)
        |-- ata1                                (ata port)
            |-- host0                           (scsi host)
                |-- target0:0:0                 (scsi target)
                    |-- 0:0:0:0                 (disk)

With this change, the ata port runtime PM is easier.
For example, the ata port runtime suspend will happen as,

disk suspend --> scsi target suspend --> scsi host suspend --> ata port
suspend.
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This is another attempt at fixing the same problem that 270dac35
(libata: ahci_start_engine compliant to AHCI spec) tried to solve.
Unfortunately, 270dac35 created regressions for a lot more common
controllers and got reverted.

This specific AHCI IP block becomes a brick if the DMA engine is
started while DRQ is set.  It is not possible to avoid the condition
completely but the most common occurrence is caused by spurious use of
ahci_start_engine() from ahci_start_port() during init sequence.

DMA engine is started after both soft and hard resets and
ahci_start_port() is always followed by resets, so there is no reason
to start DMA engine from ahci_start_port().

This patch removes ahci_start_engine() invocation from
ahci_start_port().  This change makes failure path of
ahci_port_suspend() leave engine stopped without following resets.
This is resolved by replacing ahci_start_port() call with
ata_port_freeze() which forces resets afterwards, which is the better
behavior anyway.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NBrian Norris <computersforpeace@gmail.com>
Reported-by: NJian Peng <jipeng2005@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NMichael Walle <michael@walle.cc>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NNicolas Pitre <nico@fluxnic.net>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

fix these errors:
drivers/ata/libata-sff.c:2538:3: error: implicit declaration of function
'ata_pci_bmdma_prepare_host'
drivers/ata/libata-sff.c:2549:40: error: 'ata_bmdma_interrupt'
undeclared (first use in this function)
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The change in commit 904c04fe "ahci_platform: Add the board_ids..."
doesn't work for the DT probing case as platform_get_device_id returns
NULL. Pick the default ahci_port_info in this case.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Cc: Richard Zhu <richard.zhu@linaro.org>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Drivers should not use NO_IRQ; moreover, some architectures don't
have it nowadays. '0' is the 'no irq' case.
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Reenable sending SRST to devices connected behind a Sil3726 PMP.
This allow staggered spinups and handles drives that spins up slowly.

While the drives spin up, the PMP will not accept SRST.
Most controller reissues the reset until the drive is ready, while
some [Sil3124] returns an error.
In ata_eh_error, wait 10s before reset the ATA port and try again.
Signed-off-by: NGwendal Grignou <gwendal@google.com>
Acked-by: NTejun Heo <tj@kernel.org>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Trivial spelling fix.
Signed-off-by: NChris Dunlop <chris@onthe.net.au>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Use dev_get_platdata() to retrieve the struct ahci_platform_data data
from the platform.
Signed-off-by: NJiSheng Zhang <jszhang3@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add the documentation of parameters of ata_change_queue_depth to silence the warning of make xmldocs
Signed-off-by: NMarcos paulo de Souza <marcos.mage@gmail.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add devicetree match table to ahci platform driver for Calxeda Highbank
AHCI controller.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org

A pending cleanup will mean that module.h won't be implicitly
everywhere anymore.  Make sure the modular drivers in the ide dir
are actually calling out for <module.h> explicitly in advance.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

They were getting this implicitly by an include of module.h
from device.h -- but we are going to clean that up and break
that include chain, so include export.h explicitly now.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
efar_set_dmamode() and in ata_piix.c.

Fix efar_set_piomode() documentation while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Besides making things noticably simpler it results in ~2% decrease in
the driver LOC count and also ~2% decrease in the driver binary size
(as measured on x86-32).

Fix piix_set_piomode() documentation while at it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Set SITRE (separate slave timing register) bit also in master-only
configurations to match other PIIX-alike drivers and make further
changes easier.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Always use ata_sff_data_xfer32() in ata_sff_data_xfer_noirq()
so the latter can be also used for host controllers supporting
32-bit PIO operations.

It is a completely safe thing to do because if 32-bit PIO is
not supported or enabled ata_sff_data_xfer32() will fallback
to a standard method.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fixes IDE -> libata regression.

There shouldn't be any problems with it as corresponding IDE's host
driver (aec62xx) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fixes IDE -> libata regression.

There shouldn't be any problems with it as corresponding IDE's host
driver (sl82c105) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fixes IDE -> libata regression.

There shouldn't be any problems with it as corresponding IDE's host
driver (pdc202xx_new) has been supporting PCI Power Management since
Oct 10 2008 (commit feb22b7f "ide: add proper PCI PM support (v2)")
and IDE PM since Jun 14 2003 (patch v2.5.73 "ide: Power Management").
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add controller type field to struct legacy_data and then use it
to merge together all ->set_piomode methods for QDI controllers.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

QDI65x0 controllers are fully supported by pata_legacy driver
so remove no longer needed pata_qdi driver.

Leave PATA_QDI config option for compatibility reasons and teach
pata_legacy to preserve the old behavior of pata_qdi driver.
Acked-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Rename 'idetm_port' and 'idetm_data' variables to 'master_port'
and 'master_data' respectively to match register naming used in
it8213_set_dmamode() and in ata_piix.c.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>