Add a list of switch ports within the switch fabric. This will help the
lookup of a port inside the whole fabric, and it is the first step
towards supporting multiple CPU ports, before deprecating the usage of
the unique dst->cpu_dp pointer.

In preparation for a future allocation of the dsa_port structures,
return -ENOMEM in case no structure is returned, even though this
error cannot be reached yet.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.

At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Heiner Kallweit says:

====================
The attempt to improve performance by changing the PCIe max read request
size was added in the vendor driver more than 10 years back and copied
to r8169 driver. In the vendor driver this has been removed long ago.
Obviously it had no effect, also in my tests I didn't see any
difference. Typically the max payload size is less than 512 bytes
anyway, and the PCI core takes care that the maximum supported value
is set. So let's remove fiddling with PCIe max read request size from
r8169 too. This change allows to simplify the driver in the subsequent
three patches of this series.
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

We can remove rtl_hw_start_8168bef() and use rtl_hw_start_8168b()
instead because setting register Config4 is done in
rtl_jumbo_config(), being called from rtl_hw_start().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

We can remove rtl_hw_start_8168dp() because it's the same as
rtl_hw_start_8168dp() now.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the
same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code
by moving this setting for RTL8168B to rtl_hw_start_8168().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The attempt to improve performance by changing the PCIe max read request
size was added in the vendor driver more than 10 years back and copied
to r8169 driver. In the vendor driver this has been removed long ago.
Obviously it had no effect, also in my tests I didn't see any
difference. Typically the max payload size is less than 512 bytes
anyway, and the PCI core takes care that the maximum supported value
is set. So let's remove fiddling with PCIe max read request size from
r8169 too.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Karsten Graul says:

====================
More patches to address abnormal termination processing of
sockets and link groups.
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

With the introduction of the link group termination worker there is
no longer a need to postpone smc_close_active_abort() to a worker.
To protect socket destruction due to normal and abnormal socket
closing, the socket refcount is increased.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Use a worker for link group termination to guarantee process context.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

If a link group and its connections must be terminated,
* wake up socket waiters
* do not enable buffer reuse

A linkgroup might be terminated while normal connection closing
is running. Avoid buffer reuse and its related LLC DELETE RKEY
call, if linkgroup termination has started. And use the earliest
indication of linkgroup termination possible, namely the removal
from the linkgroup list.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

There are lots of link group termination scenarios. Most of them
still allow to inform the peer of the terminating sockets about aborting.
This patch tries to call smc_close_abort() for terminating sockets.

And the internal TCP socket is reset with tcp_abort().
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Usually link groups are freed delayed to enable quick connection
creation for a follow-on SMC socket. Terminated link groups are
freed faster. This patch makes sure, fast schedule of link group
freeing is not rescheduled by a delayed schedule. And it makes sure
link group freeing is not rescheduled, if the real freeing is already
running.
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Locking hierarchy requires that the link group conns_lock can be
taken if the socket lock is held, but not vice versa. Nevertheless
socket termination during abnormal link group termination should
be protected by the socket lock.
This patch reduces the time segments the link group conns_lock is
held to enable usage of lock_sock in smc_lgr_terminate().
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

When a link group is to be terminated, it is sufficient to hold
the lgr lock when unlinking the link group from its list.
Move the lock-protected link group unlinking into smc_lgr_terminate().
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The resources for a terminated socket are being cleaned up.
This patch makes sure
* no more data is received for an actively terminated socket
* no more data is sent for an actively or passively terminated socket
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Ido Schimmel says:

====================
Vadim says:

This patch set extends the size of QSFP EEPROM for the cable types
SSF-8436 and SFF-8636 from 256 bytes to 640 bytes. This allows ethtool
to show correct information for these cable types (more details below).

Patch #1 adds a macro that computes the EEPROM page number from the
provided offset specified in the request.

Patch #2 teaches the driver to access the information stored in the
upper pages of the QSFP memory map.

Details and examples:

SFF-8436 specification defines pages 0, 1, 2 and 3. Page 0 contains
lower memory page offsets (from 0x00 to 0x7f) and upper page offsets
(from 0x80 to 0xfe). Upper pages 1, 2 and 3 are optional and can be
empty.

Page 1 is provided if upper page 0 byte 0xc3 bit 6 is set.
Page 2 is provided if upper page 0 byte 0xc3 bit 7 is set.
Page 3 is provided if lower page 0 byte 0x02 bit 2 is cleared.
Offset 0xc3 for the upper page is provided as 0x43 = 0xc3 - 0x80.

As a result of exposing 256 bytes only, ethtool shows wrong information
for pages 1, 2 and 3. In the below hex dump from ethtool for a cable
compliant to SFF-8636 specification, it can be seen that EEPROM of this
device contains optical diagnostic page (lower page 0 byte 0x02 bit 2 is
cleared), but it is not exposed, as the length defined for this type is
256 bytes.

$ ethtool -m sfp42 hex on
Offset          Values
------          ------
0x0000:         11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00
0x0010:         00 00 00 00 00 00 2a 90 00 00 82 ae 00 00 00 00
0x0020:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0030:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0040:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0050:         00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
0x0060:         00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0070:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0080:         11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23
0x0090:         00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20
0x00a0:         20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d
0x00b0:         53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05
0x00c0:         02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34
0x00d0:         36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2
0x00e0:         38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20
0x00f0:         00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00

After changing the length returned by get_module_info() callback from
256 bytes to 640 bytes, the upper pages 1, 2 and 3 are exposed by
ethtool. In the below hex dump from the same cable it can be seen that
the optical diagnostic page (page 3, from offset 0x0200) has non-zero
data.

$ ethtool -m sfp42 hex on
Offset          Values
------          ------
0x0000:         11 07 00 ff 00 ff 00 00 00 55 55 00 00 00 00 00
0x0010:         00 00 00 00 00 00 27 79 00 00 82 c5 00 00 00 00
0x0020:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0030:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0040:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0050:         00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
0x0060:         00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0070:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0080:         11 8c 0c 80 00 00 00 00 00 00 00 05 ff 00 00 23
0x0090:         00 00 32 00 4d 65 6c 6c 61 6e 6f 78 20 20 20 20
0x00a0:         20 20 20 20 00 00 02 c9 4d 4d 41 31 42 30 30 2d
0x00b0:         53 53 31 20 20 20 20 20 41 32 42 68 0b b8 46 05
0x00c0:         02 07 f5 9e 4d 54 31 38 33 34 46 54 30 33 38 34
0x00d0:         36 20 20 20 31 38 30 37 30 33 00 00 0c 10 67 c2
0x00e0:         38 32 36 46 4d 41 32 32 36 49 30 31 31 35 20 20
0x00f0:         00 00 00 00 00 00 00 00 00 00 01 00 0e 00 00 00
0x0100:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0110:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0120:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0130:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0140:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0150:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0160:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0170:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0180:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0190:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01a0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01b0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01c0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01d0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01e0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x01f0:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0200:         50 00 f6 00 46 00 00 00 00 00 00 00 00 00 00 00
0x0210:         88 b8 79 18 87 5a 7a 76 00 00 00 00 00 00 00 00
0x0220:         00 00 00 00 00 00 00 00 00 00 18 30 0e 61 60 b7
0x0230:         87 71 01 d3 43 e2 03 a5 10 9a 0a ba 0f a0 0b b8
0x0240:         87 71 02 d4 43 e2 05 a5 00 00 00 00 00 00 00 00
0x0250:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x0260:         a7 03 00 00 00 00 00 00 00 00 44 44 22 22 11 11
0x0270:         00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

And 'ethtool -m sfp42' shows the real values for the below fields, while
before it exposed zeros for these fields:

Laser bias current high alarm threshold   : 8.500 mA
Laser bias current low alarm threshold    : 5.492 mA
Laser bias current high warning threshold : 8.000 mA
Laser bias current low warning threshold  : 6.000 mA
Laser output power high alarm threshold   : 3.4673 mW / 5.40 dBm
Laser output power low alarm threshold    : 0.0724 mW / -11.40 dBm
Laser output power high warning threshold : 1.7378 mW / 2.40 dBm
Laser output power low warning threshold  : 0.1445 mW / -8.40 dBm
Module temperature high alarm threshold   : 80.00 degrees C / 176.00 F
Module temperature low alarm threshold    : -10.00 degrees C / 14.00 F
Module temperature high warning threshold : 70.00 degrees C / 158.00 F
Module temperature low warning threshold  : 0.00 degrees C / 32.00 F
Module voltage high alarm threshold       : 3.5000 V
Module voltage low alarm threshold        : 3.1000 V
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Extend the size of QSFP EEPROM for the cable types SSF8436 and SFF8636
from 256 to 640 bytes in order to expose all the EEPROM pages by
ethtool.

For SFF-8636 and SFF-8436 specifications, the driver exposes 256 bytes
of data for ethtool's get_module_eeprom() callback. This is because the
driver uses the below defines to specify SFF module length in ethtool's
get_module_info() callback:
'ETH_MODULE_SFF_8636_LEN' and 'ETH_MODULE_SFF_8436_LEN' (both are 256).

As a result of exposing 256 bytes only, ethtool shows wrong "zero" info
for pages 1, 2, 3.

The patch changes the length returned by callback for get_module_info()
to the values from the next defines: 'ETH_MODULE_SFF_8636_MAX_LEN' and
'ETH_MODULE_SFF_8436_MAX_LEN' (both are 640) to allow exposing of upper
page 1, 2 and 3.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Provide a macro for getting QSFP module EEPROM page number from the
optional upper page number row offset, specified in request.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Do some cleanup of the netback init and deinit code:

- add an omnipotent queue deinit function usable from
  xenvif_disconnect_data() and the error path of xenvif_connect_data()
- only install the irq handlers after initializing all relevant items
  (especially the kthreads related to the queue)
- there is no need to use get_task_struct() after creating a kthread
  and using put_task_struct() again after having stopped it.
- use kthread_run() instead of kthread_create() to spare the call of
  wake_up_process().
Signed-off-by: NJuergen Gross <jgross@suse.com>
Reviewed-by: NPaul Durrant <pdurrant@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Hayes Wang says:

====================
Support loading the firmware of the PHY with the type of RTL_FW_PHY_NC.
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Support the firmware of PHY NC which is used to fix the issue found
for PHY. Currently, only RTL_VER_04, RTL_VER_05, and RTL_VER_06 need
it.

The order of loading PHY firmware would be

	RTL_FW_PHY_START
	RTL_FW_PHY_NC
	RTL_FW_PHY_STOP

The RTL_FW_PHY_START/RTL_FW_PHY_STOP are used to lock/unlock the PHY,
and set/clear the patch key from the firmware file.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Move r8153_patch_request() forward for later patch.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Make sure @fw_offset field of struct fw_mac is more than the size
of struct fw_mac.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The struct fw_type_1 is used by MAC only, so rename it to a meaningful one.

Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail"
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2019-10-21

This series contains updates to e1000e and igc only.

Sasha adds stream control transmission protocol (SCTP) CRC checksum
support for igc.  Also added S0ix support to the e1000e driver.  Then
added multicast support by adding the address list to the MTA table and
providing the option for IPv6 address for igc.  In addition, added
receive checksum support to igc as well.  Lastly, cleaned up some code
that was not fully implemented yet for the VLAN filter table array.

v2: Dropped patch 1 & 2 from the original series.  Patch 1 is being sent
    to 'net' tree as a fix and patch 2 implementation needs to be
    re-worked.  Updated the patch to add support for S0ix to fix the
    reverse Xmas tree issues and made the entry/exit functions void
    since they constantly returned success.  All based on community
    feedback.
v3: Cleaned up patch 4 of the series based on feedback from the
    community.  Cleaned up a stray comma in a code comment and removed
    the 'inline' of a function that would be inlined by the compiler
    anyways.
====================
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Use tcf_tm_dump(), instead of an open coded variant (no functional change
in this patch).
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: marvell: support downshift as PHY tunable

So far downshift is implemented for one small use case only and can't
be controlled from userspace. So let's implement this feature properly
as a PHY tunable so that it can be controlled via ethtool.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of superseded function marvell_set_downshift() we can use new
function m88e1111_set_downshift() in m88e1116r_config_init().
For this m88e1116r_config_init() has to be moved in the code.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far downshift is implemented for one small use case only and can't
be controlled from userspace. So let's implement this feature properly
as a PHY tunable so that it can be controlled via ethtool.
More Marvell PHY's may support downshift, but I restricted it for now
to the ones where I have the datasheet.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added test cases for IP header operations:
- set tos/precedence
- add value to tos/precedence
- clear tos/precedence
- invert tos/precedence
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lorenzo Bianconi says:

====================
add XDP support to mvneta driver

Add XDP support to mvneta driver for devices that rely on software
buffer management. Supported verdicts are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_TX
Moreover set ndo_xdp_xmit net_device_ops function pointer in order
to support redirecting from other device (e.g. virtio-net).
Convert mvneta driver to page_pool API.
This series is based on previous work done by Jesper and Ilias.
We will send follow-up patches to reduce DMA-sync operations.

Changes since v4:
- reset page_pool pointer to NULL in mvneta_rxq_drop_pkts and in
  mvneta_create_page_pool error path
- move dma sync in mvneta_rx_refill() in patch 2/7
- verify bpf prog pointer in mvneta_xdp_setup to double-check if
  stop/start is really necessary
- coding style fixes

Changes since v3:
- rename MVNETA_XDP_CONSUMED in MVNETA_XDP_DROPPED
- squash patch 4/8 and patch 3/8
- fix dma sync for XDP_TX verdict
- fix queue_index in xdp_rxq_info_reg
- cosmetics

Changes since v2:
- rely on page_pool_recycle_direct instead of xdp_return_buff for XDP_DROP
- define xdp buffer in mvneta_rx_swbm and avoid default initializations
- use dma_sync_single_for_cpu instead of dma_sync_single_range_for_cpu
- run page_pool_release_page in mvneta_swbm_add_rx_fragment even if
  the buffer contains just ETH_FCS

Changes since v1:
- sync dma buffers before refilling hw queues
- fix stats accounting

Changes since RFC:
- implement XDP_TX
- make tx pending buffer list agnostic
- code refactoring
- check if device is running in mvneta_xdp_setup
====================
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement XDP_TX verdict and ndo_xdp_xmit net_device_ops function
pointer
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow tx buffer array to contain both skb and xdp buffers in order to
enable xdp frame recycling adding XDP_TX verdict support
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move data buffer prefetch in mvneta_swbm_rx_frame after
dma_sync_single_range_for_cpu
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic XDP support to mvneta driver for devices that rely on software
buffer management. Currently supported verdicts are:
- XDP_DROP
- XDP_PASS
- XDP_REDIRECT
- XDP_ABORTED

- iptables drop:
$iptables -t raw -I PREROUTING -p udp --dport 9 -j DROP
$nstat -n && sleep 1 && nstat
IpInReceives		151169		0.0
IpExtInOctets		6953544		0.0
IpExtInNoECTPkts	151165		0.0

- XDP_DROP via xdp1
$./samples/bpf/xdp1 3
proto 0:	421419 pkt/s
proto 0:	421444 pkt/s
proto 0:	421393 pkt/s
proto 0:	421440 pkt/s
proto 0:	421184 pkt/s
Tested-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor mvneta_rx_swbm code introducing mvneta_swbm_rx_frame and
mvneta_swbm_add_rx_fragment routines. Rely on build_skb in oreder to
allocate skb since the previous patch introduced buffer recycling using
the page_pool API.
This patch fixes even an issue in the original driver where dma buffers
are accessed before dma sync.
mvneta driver can run on not cache coherent devices so it is
necessary to sync DMA buffers before sending them to the device
in order to avoid memory corruptions. Running perf analysis we can
see a performance cost associated with this DMA-sync (anyway it is
already there in the original driver code). In follow up patches we
will add more logic to reduce DMA-sync as much as possible.
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the page_pool api for allocations and DMA handling instead of
__dev_alloc_page()/dma_map_page() and free_page()/dma_unmap_page().
Pages are unmapped using page_pool_release_page before packets
go into the network stack.

The page_pool API offers buffer recycling capabilities for XDP but
allocates one page per packet, unless the driver splits and manages
the allocated page.
This is a preliminary patch to add XDP support to mvneta driver
Signed-off-by: NIlias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce mvneta_update_stats routine to collect {rx/tx} statistics
(packets and bytes). This is a preliminary patch to add XDP support to
mvneta driver
Signed-off-by: NLorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VLAN filter table array not implemented yet and shadow_vfta pointer
not used. Clean up the code and remove the unused shadow_vfta pointer.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>