WOL is not supported for Vrtual Functions.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid accessing the hardware when UE is detected.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

> call pci msix disable in be_suspend
	> call pci msix enable in be_resume
	> stop worker thread in be_suspend
	> start worker thread in be_resume
	> stop worker thread in be_shutdown
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

be_cmd_pmac_add/del functions need to pass domain number to the firmware.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we are always using the Emulex OUI for a VF MAC address
while generating MAC for a VF.  Use OUI from current MAC instead.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF needs to cleanup all the interface handles that it created for the VFs.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid the completion processing for be_vf_eth_addr_config
to consume the link status notification before netdev_register.
Otherwise this causes the PF miss its first link status update.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While configuring QOS for VFs, the VF number should be translated
to domain number correctly.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For a host in the mesh network, the batman layer should be transparent.
However, we had one exception, data packets within the mesh network
which have the same destination as a originator are being routed to
that node, although there is no host that node's bat0 interface and
therefore gets dropped anyway. This commit removes this exception.
Signed-off-by: NLinus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

types.h is included by main.h, which is included at the beginning of any
other c-file anyway. Therefore this commit removes those duplicate
inclussions.
Signed-off-by: NLinus Lüssing <linus.luessing@ascom.ch>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

Multiple variable declarations in a single statements over multiple lines can
be split into multiple variable declarations without changing the actual
behavior.
Signed-off-by: NMarek Lindner <lindner_marek@yahoo.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>

The atl1 driver uses the legacy PCI power management, so it has to
do some PCI-specific things in its ->suspend() and ->resume()
callbacks, which isn't necessary and should better be done by the PCI
subsystem-level power management code.

Convert atl1 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested-by: NThomas Fjellstrom <thomas@fjellstrom.ca>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The atl1c driver shouldn't call device_init_wakeup() in its probe
routine with the second argument equal to 1, because for PCI devices
the wakeup capability setting is initialized as appropriate by the
PCI subsystem.  Remove the potentially harmful call.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The tg3 driver uses device_init_wakeup() in such a way that the
device's power.can_wakeup flag may be set even though the PCI
subsystem cleared it before, in which case the device cannot wake
up the system from sleep states.  Modify the driver to only change
the power.can_wakeup flag if the device is not capable of generating
wakeup signals.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current driver does not show 100MB support in ethtool.
Adding support for the same.
Signed-off-by: NAtita Shirwaikar <atita.shirwaikar@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The function ixgbe_init_mbx_params_pf isn't used unless CONFIG_PCI_IOV
is defined.  This is causing namespace warnings.  So I wrapped its
definition in CONFIG_PCI_IOV too.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We had a support function that just walked a few pointers to get
from the ixgbe_hw struct to the netdev pointer.  This was causing
a namespace warning so I removed it and just reference the pointers
directly.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We didn't need the prototype and it was causing namespace complaints so
I made it static.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This consolidates hardware specifics to ixgbe_dcb.c this simplifies
code that was previously branching based on hardware type.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This removes the RESET bit previously used to force a device
reset when DCB bandwidth configurations were changed. This can
now be done dynamically without a reset so the bit is no longer
needed. The only remaining operations that force a device reset
are DCB enable/disable and FCoE application priority changes.
DCB enable/disable is a hardware requirement.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The 82599 and 82598 devices do not require hardware resets to
configure CEE pg settings. This patch changes DCB configuration
to set the CEE pg values directly from the dcbnl ops routine.

This reduces the number of resets seen on the wire and allows
LLDP to reach a steady state faster.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implements 802.1Qaz support for ixgbe driver. Additionally,
this adds IEEE_8021QAZ_TSA_{} defines to dcbnl.h this is to
avoid having to use cryptic numeric codes for the TSA type.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the routines that configure the HW for DCB require a
ixgbe_dcb_config structure. This structure was designed to support
the CEE standard and does not match the IEEE standard well.

This patch changes the HW routines in ixgbe_dcb_8259x.{ch} to use
raw pfc and bandwidth values. This requires some parsing of the DCB
configuration but makes the HW routines independent of the data
structure that contains the DCB configuration.

The primary advantage to doing this is we can do HW setup directly
from the 802.1Qaz ops without having to arbitrarily encapsulate this
data into the CEE structure.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove round robin configuration code for 82598 parts it
is not settable and is always false.

If we need/want this in the future we can add it back properly.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If the FCoE priority is not changing do not set the RESET and
APP_UPCHG bits. This causes unneeded HW resets and which can
cause unneeded LLDP frames and negotiations.

The current check is not sufficient because the FCoE priority
can change twice during a negotiation which results in the
bits being set. This occurs when the switch changes the
priority or when the link is reset with switches that do not
include the APP priority until after PFC has been negotiated.

This results in set_app being called with the local APP
priority. Then the negotiation completes and set_app
is called again with the peer APP priority. The check
fails so the device is reset and the above occurs again
resulting in an endless loop of resets.

By only resetting the device if the APP priority has really
changed we short circuit the loop.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

...when invoked while interface is not up or when auto-negotiation is
disabled as done by other drivers.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

*e1000_gstrings_test is not the same size as e1000_gstrings_test.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As a precautionary measure, expand the fix submitted in commit
4d163b75 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The two fragments of an unicast packet must have successive sequence numbers to
allow the receiver side to detect matching fragments and merge them again. The
current implementation doesn't provide that property because a sequence of two
atomic_inc_return may be interleaved with another sequence which also changes
the variable.

The access to the fragment sequence number pool has either to be protected by
correct locking or it has to reserve two sequence numbers in a single fetch.
The latter one can easily be done by increasing the value of the last used
sequence number by 2 in a single step. The generated window of two currently
unused sequence numbers can now be scattered across the two fragments.
Reported-by: NLinus Lüssing <linus.luessing@web.de>
Signed-off-by: NSven Eckelmann <sven@narfation.org>