This is the second report of this bug.  Unfortunately the first
reporter hasn't been able to reproduce it since to provide more
debugging info.

So let's apply this patch for 2.6.14 to

1) Make this non-fatal.
2) Provide the info we need to track it down.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When netpoll is not being used, the macro that
defines the removed routing netpoll_poll_lock
defines the return as zero, but the real
routine returns a `void *`
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the RCU race on bridge delete interface.  Basically,
the network device has to be detached from the bridge in the first
step (pre-RCU), rather than later. At that point, no more bridge traffic
will come in, and the other code will not think that network device
is part of a bridge.

This should also fix the XEN test problems.
Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sequence to move over to the Linux trap tables from
the firmware ones needs to be more air tight.  It turns
out that to be %100 safe we do need to be able to translate
OBP mappings in our TLB miss handlers early.

In order not to eat up a lot of kernel image memory with
static page tables, just use the translations array in
the OBP TLB miss handlers.  That solves the bulk of the
problem.

Furthermore, to make sure the OBP TLB miss path will work
even before the fixed MMU globals are loaded, explicitly
load %g1 to TLB_SFSR at the beginning of the i-TLB and
d-TLB miss handlers.

To ease the OBP TLB miss walking of the prom_trans[] array,
we sort it then delete all of the non-OBP entries in there
(for example, there are entries for the kernel image itself
which we're not interested in at all).

We also save about 32K of kernel image size with this change.
Not a bad side effect :-)

There are still some reasons why trampoline.S can't use the
setup_trap_table() yet.  The most noteworthy are:

1) OBP boots secondary processors with non-bias'd stack for
   some reason.  This is easily fixed by using a small bootup
   stack in the kernel image explicitly for this purpose.

2) Doing a firmware call via the normal C call prom_set_trap_table()
   goes through the whole OBP enter/exit sequence that saves and
   restores OBP and Linux kernel state in the MMUs.  This path
   unfortunately does a "flush %g6" while loading up the OBP locked
   TLB entries for the firmware call.

   If we setup the %g6 in the trampoline.S code properly, that
   is in the PAGE_OFFSET linear mapping, but we're not on the
   kernel trap table yet so those addresses won't translate properly.

   One idea is to do a by-hand firmware call like we do in the
   early bootup code and elsewhere here in trampoline.S  But this
   fails as well, as aparently the secondary processors are not
   booted with OBP's special locked TLB entries loaded.  These
   are necessary for the firwmare to processes TLB misses correctly
   up until the point where we take over the trap table.

This does need to be resolved at some point.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Glibc is about to get some new high precision timer stuff that relies on
the standard timebase of the PPC architecture.

However, some (rare & old) CPUs do not have such timebase and it is a
bit annoying to have your stuff just crash because you are running on
the wrong CPU...

This exposes to userland a CPU feature bit that tells that the current
processor doesn't have a standard timebase.  It's negative logic so that
glibc will still "just work" on older kernels (it will just be unhappy
on those old CPUs but that doesn't really matter as distro tend to
update glibc & kernel at the same time).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Interestingly enough, ppc32 had broken timekeeping for ages...  It
worked, but probably drifted a bit more than could be explained by the
actual bad precision of the timebase calibration.  We discovered that
recently when somebody figured out that the common code was using
CLOCK_TICK_RATE to correct the timekeeing, and ppc32 had a completely
bogus value for it.

This patch turns it into something saner.  Probably not as good as doing
something based on the actual timebase frequency precision but I'll
leave that sort of math to others.  This at least makes it better for
the common HZ values.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Give an empty definition for clear_can_do_skas() when it is not needed.
Thanks to Junichi Uekawa <dancer@netfort.gr.jp> for reporting the
breakage and providing a fix (I re-fixed it in an IMHO cleaner way).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch to use host AIO support that I submitted early after 2.6.13 exposed
some problems in the block driver.  I have fixes for these, but am not
comfortable putting them into 2.6.14 at this late date.  So, this patch reverts
the use of host AIO.

I will resubmit the original patch, plus fixes to the driver after 2.6.14
in order to get a reasonable amount of testing before they're exposed to
the general public.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We were not doing alignment properly when remapping the kernel image.

What we want is a 4MB aligned physical address to map at KERNBASE.
Mistakedly we were 4MB aligning the virtual address where the kernel
initially sits, that's wrong.

Instead, we should PAGE align the virtual address, then 4MB align the
physical address result the prom gives to us.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refuse to install a page into a mapping if the mapping count is already
ridiculously large.

You probably cannot trigger this on 32-bit architectures, but on a
64-bit setup we should protect against it.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Newer gcc's are generating this relocation, so the module loader needs to
handle it.
Signed-off-by: NPeter Bergner <bergner@vnet.ibm.com>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* bttv-cards.c:
- Enable S-Video input on DViCO FusionHDTV5 Lite
Signed-off-by: NMichael Krufky <mkrufky@m1k.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch prevents illegal traps from causing m32r kernel's infinite loop
execution.
Signed-off-by: NNaoto Sugai <sugai@isl.melco.co.jp>
Signed-off-by: NHirokazu Takata <takata@linux-m32r.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Nir Tzachar <tzachar@cs.bgu.ac.il> points out that if an ELF file specifies a
zero-length bss at a whacky address, we cannot load that binary because
padzero() tries to zero out the end of the page at the whacky address, and
that may not be writeable.

See also http://bugzilla.kernel.org/show_bug.cgi?id=5411

So teach load_elf_binary() to skip the bss settng altogether if the elf file
has a zero-length bss segment.

Cc: Roland McGrath <roland@redhat.com>
Cc: Daniel Jacobowitz <dan@debian.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I've noticed that the calculations for seg_size and nr_segs in
__dma_sync_page_highmem() (arch/ppc/kernel/dma-mapping.c) are wrong.  The
incorrect calculations can result in either an oops or a panic when running
fsck depending on the size of the partition.

The problem with the seg_size calculation is that it can result in a
negative number if size is offset > size.  The problem with the nr_segs
caculation is returns the wrong number of segments, e.g.  it returns 1 when
size is 200 and offset is 4095, when it should return 2 or more.
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert this recent correctness change: Douglas Crosher <dcrosher@scieneer.com>
reported that it broke an existing application, and that madvise() works
without error on anonymous mappings on Solaris.

This means that madvise() will remain non-standards-compliant: we should
return -EBADF for all requests against non-file-backed vma's, but Linux only
does this for MADV_WILLNEED requests.
Signed-off-by: NSuzuki K P <suzuki@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Here is a compatibility fix between Linux and Solaris when used with VxFS
filesystems: Solaris usually accepts acl entries in any order, but with
VxFS it replies with NFSERR_INVAL when it sees a four-entry acl that is not
in canonical form.  It may also fail with other non-canonical acls -- I
can't tell, because that case never triggers: We only send non-canonical
acls when we fake up an ACL_MASK entry.

Instead of adding fake ACL_MASK entries at the end, inserting them in the
correct position makes Solaris+VxFS happy.  The Linux client and server
sides don't care about entry order.  The three-entry-acl special case in
which we need a fake ACL_MASK entry was handled in xdr_nfsace_encode.  The
patch moves this into nfsacl_encode.
Signed-off-by: NAndreas Gruenbacher <agruen@suse.de>
Acked-by: NTrond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

v9fs_file_read and v9fs_file_write use kmalloc to allocate buffers as big
as the data buffer received as parameter.  kmalloc cannot be used to
allocate buffers bigger than 128K, so reading/writing data in chunks bigger
than 128k fails.

This patch reorganizes v9fs_file_read and v9fs_file_write to allocate only
buffers as big as the maximum data that can be sent in one 9P message.
Signed-off-by: NLatchesar Ionkov <lucho@ionkov.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In the current dell_rbu code ver 2.0 the packet update mechanism makes the
user app dump every individual packet in to the driver.

This adds in efficiency as every packet update makes the
/sys/class/firmware/dell_rbu/loading and data files to disappear and reappear
again.  Thus the user app needs to wait for the files to reappear to dump
another packet.  This slows down the packet update tremendously in case of
large number of packets.  I am submitting a new patch for dell_rbu which will
change the way we do packet updates;

In the new method the user app will create a new single file which has already
packetized the rbu image and all the packets are now staged in this file.

This driver also creates a new entry in
/sys/devices/platform/dell_rbu/packet_size ; the user needs to echo the packet
size here before downloading the packet file.

The user should do the following:

 create one single file which has all the packets stacked together.
 echo the packet size in to /sys/devices/platform/dell_rbu/packet_size.
 echo 1 > /sys/class/firmware/dell_rbu/loading
 cat the packetfile > /sys/class/firmware/dell_rbu/data
 echo 0 > /sys/class/firmware/dell_rbu/loading

The driver takes the file which came through /sys/class/firmware/dell_rbu/data
and takes chunks of paket_size data from it and place in contiguous memory.

This makes packet update process very efficient and fast.  As all the packet
update happens in one single operation.  The user can still read back the
downloaded file from /sys/devices/platform/dell_rbu/data.
Signed-off-by: NAbhay Salunke <abhay_salunke@dell.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

pSeries_irq_bus_setup is marked __devinit but references s7a_workaround
which is marked __initdata.

Depending on who got the memory for s7a_workaround (and if the value was
now positive), it was possible for PCI hotplugged devices to have 3
subtracted from their interrupt number.  This would happen randomly and
caused me much confusion :)
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Search for a disconnect ccw_device on the ccw bus rather than on the css
bus (was a typo in patch I did for the klist conversion).  A cast to an
embedding ccw_device from an embedded device in a struct subchannel will
lead us to oopses.
Signed-off-by: NCornelia Huck <cohuck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

for certain NICs

Reverting 685fac63:
> [PATCH] e100: CPU cycle saver microcode
>
>
> Add cpu cycle saver microcode to 8086:{1209/1229} other than ICH devices.
>
> Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
> Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
> Signed-off-by: John Ronciak <john.ronciak@intel.com>
> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

This is required to avoid unloading a module that has active timewait
sockets, such as DCCP.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed by Andrea Bittau, that provided a patch that was modified to
not transition from RESPOND to OPEN when receiving DATA packets.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency with ccid_exit and to fix a bug when
IP_DCCP_UNLOAD_HACK is enabled as the control sock is not associated
to any CCID.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support to change the state of the private protocol
information via conntrack_netlink.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ability of changing the state a TCP connection. I know
that this must be used with care but it's required to provide a complete
conntrack creation via conntrack_netlink. So I'll document this aspect on
the upcoming docs.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initially we used 64bit counters for conntrack-based accounting, since we
had no event mechanism to tell userspace that our counters are about to
overflow.  With nfnetlink_conntrack, we now have such a event mechanism and
thus can save 16bytes per connection.
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the following bugs in ESP:

* Fix transport mode MTU overestimate.  This means that the inner MTU
  is smaller than it needs be.  Worse yet, given an input MTU which
  is a multiple of 4 it will always produce an estimate which is not
  a multiple of 4.

  For example, given a standard ESP/3DES/MD5 transform and an MTU of
  1500, the resulting MTU for transport mode is 1462 when it should
  be 1464.

  The reason for this is because IP header lengths are always a multiple
  of 4 for IPv4 and 8 for IPv6.

* Ensure that the block size is at least 4.  This is required by RFC2406
  and corresponds to what the esp_output function does.  At the moment
  this only affects crypto_null as its block size is 1.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses the macro ALIGN in all the applicable spots for ESP.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Breakage noted by Al Viro.

It breaks non-PCI builds, it's probably better to have a more
direct implementation on sparc32, and which driver actually
needs this is still questionable.

We can resolve this in 2.6.15
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To keep consistency, the TCP private protocol information is nested
attributes under CTA_PROTOINFO_TCP. This way the sequence of attributes to
access the TCP state information looks like here below:

CTA_PROTOINFO
CTA_PROTOINFO_TCP
CTA_PROTOINFO_TCP_STATE

instead of:

CTA_PROTOINFO
CTA_PROTOINFO_TCP_STATE
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this #include, __be16 is not defined and userspace programs
will break.
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ID is only required by ICMP type 8 (echo), so it's not
mandatory for all sort of ICMP connections. This patch makes
mandatory only the type and the code for ICMP netlink messages.
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>