In virtual environments (namely, Xen Dom0) virt <-> phys and
virt <-> isa-bus translations cannot be freely interchanged (and
even outside such environments it is not really correct to do so).
When looking at memory below 1M, the latter translations should
always be used.

iscsi_ibft_find.c part from: Martin Wilck <martin.wilck@ts.fujitsu.com>.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NPeter Jones <pjones@redhat.com>
Signed-off-by: NKonrad Rzeszutek Wilk <ketuzsezs@darnok.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the display of a few fields in the iBFT NIC attribute structure in
sysfs.

Ensure that, if the DHCP IP address and the subnet mask for the interface
is present in the iBFT NIC structure, the corresponding entries are
created in sysfs tree for the device.  This would hence create the
additional entries in the tree based on the iBFT table and would not
delete any existing entries.
Signed-off-by: NAshutosh Naik <ashutosh.naik@gmail.com>
Cc: Vishnu V <vishnu@chelsio.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

 drivers/firmware/iscsi_ibft.c: In function ‘ibft_init’:
 drivers/firmware/iscsi_ibft.c:942: warning: format ‘%lx’ expects type ‘long unsigned int’, but argument 2 has type ‘phys_addr_t’
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Using NIPQUAD() with NIPQUAD_FMT, %d.%d.%d.%d or %u.%u.%u.%u
can be replaced with %pI4
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The iscsi_ibft.c changes are almost certainly a bugfix as the
pointer 'ip' is a u8 *, so they never print the last 8 bytes
of the IPv6 address, and the eight bytes they do print have
a zero byte with them in each 16-bit word.

Other than that, this should cause no difference in functionality.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tejun's commit 7b595756 made sysfs
attribute->owner unnecessary.  But the field was left in the structure to
ease the merge.  It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!

This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 .  We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test.  Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.

akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'.  But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.

[akpm: remove the ifdef for now]
Signed-off-by: NParag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch makes the following needlessly global functions static:
- ibft_attr_show_initiator()
- ibft_attr_show_nic()
- ibft_attr_show_target()
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NKonrad Rzeszutek <ketuzsezr@darnok.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I got this patch through Red Hat's bugzilla from the bug submitter and
patch creator.  I have just fixed it up so it applies without fuzz to
upstream kernels.

Original patch and description from Shyam kumar Iyer:

The issue [ibft module not displaying targets with short names] is because
of an offset calculatation error in the iscsi_ibft.c code.  Due to this
error directory structure for the target in /sys/firmware/ibft does not
get created and so the initiator is unable to connect to the target.

Note that this bug surfaced only with an name that had a short section at
the end.  eg: "iqn.1984-05.com.dell:dell".  It did not surface when the
iqn's had a longer section at the end.  eg:
"iqn.2001-04.com.example:storage.disk2.sys1.xyz"

So, the eot_offset was calculated such that an extra 48 bytes i.e.  the
size of the ibft_header which has already been accounted was subtracted
twice.

This was not evident with longer iqn names because they would overshoot
the total ibft length more than 48 bytes and thus would escape the bug.
Signed-off-by: NShyam Kumar Iyer <shyam_iyer@dell.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Cc: Konrad Rzeszutek <konrad@virtualiron.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add /sysfs/firmware/ibft/[initiator|targetX|ethernetX] directories along with
text properties which export the the iSCSI Boot Firmware Table (iBFT)
structure.

What is iSCSI Boot Firmware Table?  It is a mechanism for the iSCSI tools to
extract from the machine NICs the iSCSI connection information so that they
can automagically mount the iSCSI share/target.  Currently the iSCSI
information is hard-coded in the initrd.  The /sysfs entries are read-only
one-name-and-value fields.

The usual set of data exposed is:

# for a in `find /sys/firmware/ibft/ -type f -print`; do  echo -n "$a: ";  cat $a; done
/sys/firmware/ibft/target0/target-name: iqn.2007.com.intel-sbx44:storage-10gb
/sys/firmware/ibft/target0/nic-assoc: 0
/sys/firmware/ibft/target0/chap-type: 0
/sys/firmware/ibft/target0/lun: 00000000
/sys/firmware/ibft/target0/port: 3260
/sys/firmware/ibft/target0/ip-addr: 192.168.79.116
/sys/firmware/ibft/target0/flags: 3
/sys/firmware/ibft/target0/index: 0
/sys/firmware/ibft/ethernet0/mac: 00:11:25:9d:8b:01
/sys/firmware/ibft/ethernet0/vlan: 0
/sys/firmware/ibft/ethernet0/gateway: 192.168.79.254
/sys/firmware/ibft/ethernet0/origin: 0
/sys/firmware/ibft/ethernet0/subnet-mask: 255.255.252.0
/sys/firmware/ibft/ethernet0/ip-addr: 192.168.77.41
/sys/firmware/ibft/ethernet0/flags: 7
/sys/firmware/ibft/ethernet0/index: 0
/sys/firmware/ibft/initiator/initiator-name: iqn.2007-07.com:konrad.initiator
/sys/firmware/ibft/initiator/flags: 3
/sys/firmware/ibft/initiator/index: 0

For full details of the IBFT structure please take a look at:
ftp://ftp.software.ibm.com/systems/support/system_x_pdf/ibm_iscsi_boot_firmware_table_v1.02.pdf

[akpm@linux-foundation.org: fix build]
Signed-off-by: NKonrad Rzeszutek <konradr@linux.vnet.ibm.com>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Peter Jones <pjones@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>