rename st-pwm to pwm-regulator. And support getting voltage & duty table from
device tree, other platforms can also use this driver without any modify.
Signed-off-by: NChris Zhong <zyw@rock-chips.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Tested-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: NJames Ban <james.ban.opensource@diasemi.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Make this driver depend on I2C and select REGMAP_I2C to fix build failure.
Also allows this driver to be built as module.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).

The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

AXP202 and AXP209 come with two synchronous step-down DC-DCs and five
LDOs. This patch introduces basic support for those regulators.
Signed-off-by: NCarlo Caione <carlo@caione.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add support for S2MPA01 voltage and current regulator.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Add a regulator driver for the BCM590xx PMU voltage regulators.
The driver supports LDOs and DCDCs in normal mode only. There is
no support for low-power mode or power sequencing.
Signed-off-by: NMatt Porter <mporter@linaro.org>
Reviewed-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMarkus Mayer <markus.mayer@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NRobin Gong <b38343@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Acked-by: NMark Brown <broonie@linaro.org>
Tested-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Tested-by: NStefan Roese <sr@denx.de>
Signed-off-by: NChris Ball <chris@printf.net>

This is a DT-only driver, so make it depend on OF and remove of_match_ptr in
the code.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds support for TPS65218 PMIC regulators.

The regulators set consists of 6 DCDCs and 1 LDO. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: NKeerthy <j-keerthy@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NWenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Make PFUZE100 entry consistent with other Freescale PMIC entries, so that now
we can have:

	<*>   Freescale MC13783 regulator driver
	<*>   Freescale MC13892 regulator driver
	<*>   Freescale PFUZE100 regulator driver
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NRobin Gong <yibin.gong@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

MAX14577 chip is a multi-function device which includes MUIC,
charger and voltage regulator. The driver is located in drivers/mfd.

This patch adds regulator driver for MAX14577 chip. There are two
regulators in this chip:
1. Safeout LDO with constant voltage output of 4.9V. It can be only
   enabled or disabled.
2. Current regulator for the charger. It provides current from 90mA up
   to 950mA.
Driver supports Device Tree.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The AMS AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DCDC step down regulators, 3 DCDC step down
controller, 11 LDOs.

Add a driver to support accessing the DCDC/LDOs found on the AMS
AS3722 PMIC using regulators.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NFlorian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The ST Microelectronics STw481x PMIC used for the Nomadik
has one single software-controlled regulator for VMMC.
This driver registers directly to the compatible string
as there is just one regulator.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

When a system has said that it has fully specified constraints for its
regulators it is still possible that some supplies may be missing,
especially if regulator support has been added to a driver after the
board was integrated. We can handle such situations more gracefully by
providing a dummy regulator.

Unless the caller has specifically indicated that the system design may
not include a given regulator by using regulator_get_optional() or that
it needs its interactions to have an effect using regulator_get_exclusive()
provide a dummy regulator if we can't locate a real one.

The kconfig option REGULATOR_DUMMY that provided similar behaviour for all
regulators has been removed, systems that need it should flag that they
have full constraints instead.
Signed-off-by: NMark Brown <broonie@linaro.org>

lp872x regulator driver can be built a module after commit 631a1fc4
"regulator: build: Allow most regulators to be built as modules".
Make REGULATOR_LP872X depend on I2C to allow building lp872x module when I2C=m.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Mostly for testing without bloating the kernel image rather than actual
utility.
Signed-off-by: NMark Brown <broonie@linaro.org>

The driver adds support for the following DA9063 PMIC regulators:
 - 11x LDOs (named LDO1 - LDO11),
 - 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),

Regulators provide following operations:
 - REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
 - REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
     - LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
     - buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
       and REGULATOR_MODE_STANDBY,
 - REGULATOR_CHANGE_CURRENT for buck converters (current limits).

The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.

Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.

This driver requires MFD core driver for operation.
Signed-off-by: NKrystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: NSteve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: NDavid Dajun Chen <david.chen@diasemi.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This fixes below build errors:

  CC [M]  drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:342:21: error: variable 'pfuze_regmap_config' has initializer but incomplete type
drivers/regulator/pfuze100-regulator.c:343:2: error: unknown field 'reg_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:343:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:343:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: error: unknown field 'val_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:344:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: error: unknown field 'max_register' specified in initializer
drivers/regulator/pfuze100-regulator.c:345:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: error: unknown field 'cache_type' specified in initializer
drivers/regulator/pfuze100-regulator.c:346:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c: In function 'pfuze100_regulator_probe':
drivers/regulator/pfuze100-regulator.c:370:2: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
drivers/regulator/pfuze100-regulator.c:370:21: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[2]: *** [drivers/regulator/pfuze100-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add pfuze100 regulator driver.
Signed-off-by: NRobin Gong <b38343@freescale.com>
Tested-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

This driver can be built as a module, make it depend on MFD_88PM800.
Otherwise, we are not able to select this driver when MFD_88PM800=m.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add the regulator driver for PMIC 88pm800 including device tree
support.
88pm800 is an I2C-based power-management IC containing voltage
regulators, a real-time clock, and some general purpose ADC devices,
Signed-off-by: NYi Zhang <yizhang@marvell.com>
Signed-off-by: NChao Xie <chao.xie@marvell.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Reduces merge issues if nothing else.
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds new regulator driver to support max77693 chip's regulators.
max77693 has two linear voltage regulators and one current regulator which
can be controlled through I2C bus. This driver also supports device tree.
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: NMyungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.

Texas Instruments' SmartReflex 2 technology provides support for this
power management technique with Forward Body Biasing (FBB) and Reverse
Body Biasing (RBB). These modulate the body voltage of transistor
cells or blocks dynamically to gain performance and reduce leakage.
TI's SmartReflex white paper[1] has further information for usage in
conjunction with other power management techniques.

The application of FBB/RBB technique is determined for each unique
device in some process nodes, whereas, they are mandated on other
process nodes.

In a nutshell, ABB technique is implemented on TI SoC as an on-chip
LDO which has ABB module controlling the bias voltage. However, the
voltage is unique per device. These vary per SoC family and the manner
in which these techniques are used may vary depending on the Operating
Performance Point (OPP) voltage targeted. For example:
OMAP3630/OMAP4430: certain OPPs mandate usage of FBB independent of
	devices.
OMAP4460/OMAP4470: certain OPPs mandate usage of FBB, while others may
	optionally use FBB or optimization with RBB.
OMAP5: ALL OPPs may optionally use ABB, and ABB biasing voltage is
	influenced by vset fused in s/w and requiring s/w override of
	default values.

Further, two generations of ABB module are used in various TI SoCs.
They have remained mostly register field compatible, however the
register offset had switched between versions.

We introduce ABB LDO support in the form of a regulator which is
controlled by voltages denoting the desired Operating Performance
Point which is targeted. However, since ABB transition is part of OPP
change sequence, the sequencing required to ensure sane operation
w.r.t OPP change is left to the controlling driver (example: cpufreq
SoC driver) using standard regulator operations.

The driver supports all ABB modes and ability to override ABB LDO vset
control efuse based ABB mode detection etc.

Current implementation is heavily influenced by the original patch
series [2][3] from Mike Turquette. However, the current implementation
supports only device tree based information.

[1] http://www.ti.com/pdfs/wtbu/smartreflex_whitepaper.pdf
[2] http://marc.info/?l=linux-omap&m=134931341818379&w=2
[3] http://marc.info/?l=linux-arm-kernel&m=134931402406853&w=2

[nm@ti.com: co-developer]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NAndrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

If we are in non-bypass mode then the SYSCLK is required for full charge
pump operation, otherwise we will fall back to bypass mode. Use the DAPM
context exposed by the ASoC driver to manage this.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch is for new lp8755 regulator dirver and
several unsed variables were deleted and then test was done.

LP8755 :
The LP8755 is a high performance power management unit.It contains
six step-down DC-DC converters which can can be filexibly bundled
together in multiphase converters as required by application.
www.ti.com
Signed-off-by: NDaniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This driver supports the 4 DCDC and 8 LDO regulators on the AS3711 PMIC.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.

Add regulator driver for this device.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.

This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.

This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.
Signed-off-by: NDavid Dajun Chen <dchen@diasemi.com>
Signed-off-by: NAshish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>