- 08 3月, 2015 1 次提交
-
-
由 Emmanuel Grumbach 提交于
The commits below broke compilation when CONFIG_IWLWIFI_DEBUGFS is not set. FIx that. Fixes: ddf89ab1 ("iwlwifi: mvm: allow to force the Rx chains from debugfs") Fixes: 9d761fd8 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons") Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 02 3月, 2015 13 次提交
-
-
由 David Spinadel 提交于
Currently scan params structure has only active or passive dwell time fields, passive one is used for fragmented scans too. FW needs the passive dwell time even when performing fragmented scan for calculating time between channels. Add a separate parameter for fragmented dwell time and pass both fragmented and passive to FW. Signed-off-by: NDavid Spinadel <david.spinadel@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Lots of issues can be caught when the RSSI drops. Add the ability to collect the firmware data at that point. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
It can be very useful to monitor the statistics and trigger a firmware dump when a certain value hits a certain offset. Since the statistics are huge, add a generic trigger. When the DWORD at offset X reaches value Y. Since there is another trigger before this one I can't add right now because of a dependency on mac80211, add a reserved entry to keep the enum in place. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Sometimes the firmware will have a hard coded configuration. In this case, the driver won't find any configuration in the firmware file, and it will have to re-start recording in case it has been stopped. This can't be done by the configuration host command since there is no such host command configured. Do that with the registers instead. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This will allow to collect the data as soon the firmware sends a specific notification of command response. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
We fire the trigger when the channel switch starts, but the delay is configurable. That makes is easier to catch channel switches that fail. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Missing beacons is a good indication that something is going wrong in the firmware. Add a trigger to be able to collect data when we start missing beacons with a configurable threshold. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Now that the firmware dump can be triggered by events in the code and not only the user or an firmware ASSERT, we need a way to know why the firmware dump was triggered. Add a section in the dump file for that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Most of the time, the issues we want to debug with the firmware dump mechanism are transient. It is then very hard to stop the recording on time and get meaningful data. In order to solve this, I add here an infrastucture of triggers. The user will supply a list of triggers that will start / stop the recording. We have two types of triggers: start and stop. Start triggers can start a specific configuration. The stop triggers will be able to kick the collection of the data with the currently running configuration. These triggers are given to the driver by the .ucode file - just like the configuration. In the next patches, I'll add triggers in the code. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 David Spinadel 提交于
20 ms fragments are no longer required by system. Signed-off-by: NDavid Spinadel <david.spinadel@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This is useful to debug weird antenna problems. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
Packet Level Co-Running is a BT Coex feature which is supported on certain devices only, hence the need for a TLV flag for it. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
We shouldn't call iwl_mvm_d3_disconnect_iter() on the running interfaces when we are woken up due to net-detect, because it doesn't make sense. Additionally, this seems to set the IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection on the next resume (if a normal WoWLAN is used). To solve this, skip the iteration loop when net-detect is set. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Reported-by: NSamuel Tan <samueltan@chromium.org> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 01 3月, 2015 17 次提交
-
-
由 Emmanuel Grumbach 提交于
The new API slightly changes the layout of the version of the firmware - prepare for that. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
Report the average beacon signal and the number of received beacons as measured by the firmware. Since the firmware just counts, and doesn't reset the counter at all, clear it in the firmware whenever we associate. However, accumulate it over firmware restart. Since clearing the statistics in the firmware will also clear the ones for the radio statistics, add those to the accumulator when cleared. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
Due to HW bug in the DBGC when driver want to stop the dbg recording it should wait 100us before collecting the data instead of write 0 to DBGC_OUT_CTRL. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
The legacy scan API is deprecated and not used anymore with 10 and higher firmware versions. Since we deprecated firmware version 9, we can remove a whole lot of unused code. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Luciano Coelho 提交于
This firmware is not supported anymore. Stop loading this firmware. Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
Export the radio statistics from the statistics v10 API (if the firmware also has the capability to fill these statistics) using the global survey data facility. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Johannes Berg 提交于
New firmware versions will report statistics using a new version 10 of the API, instead of the current version 8. Add support for this. This enables getting beacon and radio statistics. Signed-off-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Emmanuel Grumbach 提交于
This allows to use the firmware debugging system even when the configuration values are set hard coded in the firmware. Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
Cleanup unused code. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
The shared antenna should be forbidden to use only if there's high BT activity. Comparing to BT_OFF was effectively causing us to always forbid using the shared antenna for SISO. This leads to degraded performance in scenarios where the shared antenna would have better performance. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
Add this to the info printed when reading rate_scale_table. Useful for debugging. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
ss_force is a debugging option to force a certain single stream tx mode. It's not useful if it gets reset after tx idle. Fix that. While at it also make sure any code touching ss_force will only get compiled if debugfs support is configured. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eran Harary 提交于
Newer devices have more PAPD channel groups. Signed-off-by: NEran Harary <eran.harary@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Arik Nemtsov 提交于
When a TDLS station is being drained its Tx queues are still in use. Don't allocate them to a different station in the meantime. Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
Due to issues with Miracast adapters MIMO reception disable use of MIMO when for low latency P2P traffic. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
Once the FW supports autonomous decision between STBC/BFER/SISO we no longer set the STBC bit and ANT_AB in the rate table. However the FW rate in the tx response will have the STBC or BFER bit set and the antennas set to ANT_AB in case these were chosen by it. This will cause us to discard any such response as unmatching the current LQ table and thus break the rs search cycle completely. Fix this by relaxing the rate matching in case we're working with the new API and STBC/BFER are used. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Reviewed-by: NJohannes Berg <johannes.berg@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
由 Eyal Shapira 提交于
The check to avoid the shared antenna was passed the wrong antenna parameter. It should have checked whether the antenna of the next column we're considering is allowed and instead it was passed the current antenna. This could lead to a wrong choice of the next column in the rs algorithm and non optimal performance. Fixes: commit 219fb66b ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high") Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 24 2月, 2015 1 次提交
-
-
由 Eyal Shapira 提交于
Currently rs uses the info in mac80211 tx status which is a translation of the actual rate coming up from the FW in the tx response. This is matched up against the LQ table first rate to make sure this tx frame used the current LQ table. Instead of using the translated mac80211 info it's easier and cleaner to just pass the actual tx response rate in the driver private data and use that for matching. This becomes even more important once the FW begins to decide on its own whether to use STBC/BFER/SISO. Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com> Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
-
- 18 2月, 2015 8 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking updates from David Miller: 1) Missing netlink attribute validation in nft_lookup, from Patrick McHardy. 2) Restrict ipv6 partial checksum handling to UDP, since that's the only case it works for. From Vlad Yasevich. 3) Clear out silly device table sentinal macros used by SSB and BCMA drivers. From Joe Perches. 4) Make sure the remote checksum code never creates a situation where the remote checksum is applied yet the tunneling metadata describing the remote checksum transformation is still present. Otherwise an external entity might see this and apply the checksum again. From Tom Herbert. 5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire. 6) Don't explicitly initialize timer struct fields, use setup_timer() and mod_timer() instead. From Vaishali Thakkar. 7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi Nomura. 8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet. 9) Don't potentially perform skb_get() on shared skbs, also from Eric Dumazet. 10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin KaFai Lau. 11) Fix merge resolution error between the iov_iter changes in vhost and some bug fixes that occurred at the same time. From Jason Wang. 12) If rtnl_configure_link() fails we have to perform a call to ->dellink() before unregistering the device. From WANG Cong. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits) net: dsa: Set valid phy interface type rtnetlink: call ->dellink on failure when ->newlink exists com20020-pci: add support for eae single card vhost_net: fix wrong iter offset when setting number of buffers net: spelling fixes net/core: Fix warning while make xmldocs caused by dev.c net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081 ipv6: fix ipv6_cow_metrics for non DST_HOST case openvswitch: Fix key serialization. r8152: restore hw settings hso: fix rx parsing logic when skb allocation fails tcp: make sure skb is not shared before using skb_get() bridge: netfilter: Move sysctl-specific error code inside #ifdef ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc ipvlan: add a missing __percpu pcpu_stats tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one() bgmac: fix device initialization on Northstar SoCs (condition typo) qlcnic: Delete existing multicast MAC list before adding new net/mlx5_core: Fix configuration of log_uar_page_sz sunvnet: don't change gso data on clones ...
-
git://neil.brown.name/md由 Linus Torvalds 提交于
Pull md bugfixes from Neil Brown: "Three bug md fixes for 3.20 yet-another-livelock in raid5, and a problem with write errors to 4K-block devices" * tag 'md/3.20-fixes' of git://neil.brown.name/md: md/raid5: Fix livelock when array is both resyncing and degraded. md/raid10: round up to bdev_logical_block_size in narrow_write_error. md/raid1: round up to bdev_logical_block_size in narrow_write_error
-
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras由 Linus Torvalds 提交于
Pull mcelog regression fix from Tony Luck: "Fix regression - functions on the mce notifier chain should not be able to decide that an event should not be logged" * tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras: x86/mce: Fix regression. All error records should report via /dev/mcelog
-
git://git.lwn.net/linux-2.6由 Linus Torvalds 提交于
Pull DocBook build fix from Jonathan Corbet: "Fix the DocBook build failure caused by the move of the i2o subsystem to the staging tree" * tag 'docs-fix' of git://git.lwn.net/linux-2.6: Fix docs build failure caused by i2o removal
-
git://linux-nfs.org/~bfields/linux由 Linus Torvalds 提交于
Pull nfsd bugfixes from Bruce Fields: "These are fixes for two bugs introduced during the merge window" * 'for-3.20' of git://linux-nfs.org/~bfields/linux: nfsd4: fix v3-less build nfsd: fix comparison in fh_fsid_match()
-
由 NeilBrown 提交于
Commit a7854487: md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write. Causes an RCW cycle to be forced even when the array is degraded. A degraded array cannot support RCW as that requires reading all data blocks, and one may be missing. Forcing an RCW when it is not possible causes a live-lock and the code spins, repeatedly deciding to do something that cannot succeed. So change the condition to only force RCW on non-degraded arrays. Reported-by: NManibalan P <pmanibalan@amiindia.co.in> Bisected-by: NJes Sorensen <Jes.Sorensen@redhat.com> Tested-by: NJes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NNeilBrown <neilb@suse.de> Fixes: a7854487 Cc: stable@vger.kernel.org (v3.7+)
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs由 Linus Torvalds 提交于
Pull lazytime mount option support from Al Viro: "Lazytime stuff from tytso" * 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: ext4: add optimization for the lazytime mount option vfs: add find_inode_nowait() function vfs: add support for a lazytime mount option
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs由 Linus Torvalds 提交于
Pull iov_iter updates from Al Viro: "More iov_iter work - missing counterpart of iov_iter_init() for bvec-backed ones and vfs_read_iter()/vfs_write_iter() - wrappers for sync calls of ->read_iter()/->write_iter()" * 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: fs: add vfs_iter_{read,write} helpers new helper: iov_iter_bvec()
-