When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For certain platforms, it causes USB reset periodically.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable U2P3 may miss zero packet for bulk-in.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the runtime resume doesn't work normally for linking change.

1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: NJames Hughes <james.hughes@raspberrypi.org>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.

Fixes: 40a82917 ("net/usb/r8152: enable interrupt transfer")
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx_tx_bh() makes sure to not exceed MAX_SINGLE_PACKET_SIZE
bytes in the aggregated packets it builds, but does
nothing to prevent large GSO packets being submitted.

Pierre-Francois reported various hangs when/if TSO is enabled.

For localy generated packets, we can use netif_set_gso_max_size()
to limit the size of TSO packets.

Note that forwarded packets could still hit the issue,
so a complete fix might require implementing .ndo_features_check
for this driver, forcing a software segmentation if the size
of the TSO packet exceeds MAX_SINGLE_PACKET_SIZE.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NRENARD Pierre-Francois <pfrenard@gmail.com>
Tested-by: NRENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RM500Q is a 5G module from Quectel, supporting both standalone and
non-standalone modes. The normal Quectel quirks apply (DTR and dynamic
interface numbers).
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

If skb_linearize() fails, we need to free the skb.

TSO makes skb bigger, and this bug might be the reason
Raspberry Pi 3B+ users had to disable TSO.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NRENARD Pierre-Francois <pfrenard@gmail.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Display the return code as decimal integer.

Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: NCristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Lan78xx driver accesses the PHY registers through MDIO bus over USB
connection. When performing a suspend/resume, the PHY registers can be
accessed before the USB connection is resumed. This will generate an
error and will prevent the device to resume correctly.
This patch adds the dependency between the MDIO bus and USB device to
allow correct handling of suspend/resume.

Fixes: ce85e13a ("lan78xx: Update to use phylib instead of mii_if_info.")
Signed-off-by: NCristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().

This patch is generated using following script:

EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"

git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do

	if [[ "$file" =~ $EXCLUDE_FILES ]]; then
		continue
	fi
	sed -i  -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: NPankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.comCo-developed-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NKees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net

This patch corrects the SPDX License Identifier style in
header files related to drivers for USB Network devices.
This patch gives an explicit block comment to the
SPDX License Identifier.

Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20Signed-off-by: NPhong Tran <tranmanphong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20Signed-off-by: NPhong Tran <tranmanphong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables the use of SW timestamping.

ax88179_178a uses the usbnet transmit function usbnet_start_xmit() which
implements software timestamping. ax88179_178a overrides ethtool_ops but
missed to set .get_ts_info. This caused SOF_TIMESTAMPING_TX_SOFTWARE
capability to be not available.
Signed-off-by: NAndreas K. Besslein <besslein.andreas@gmail.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.

1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().

For #1, use the same solution as commit 84811412 ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both rtl_work_func_t() and rtl8152_close() call napi_disable().
Since the two calls aren't protected by a lock, if the close
function starts executing before the work function, we can get into a
situation where the napi_disable() function is called twice in
succession (first by rtl8152_close(), then by set_carrier()).

In such a situation, the second call would loop indefinitely, since
rtl8152_close() doesn't call napi_enable() to clear the NAPI_STATE_SCHED
bit.

The rtl8152_close() function in turn issues a
cancel_delayed_work_sync(), and so it would wait indefinitely for the
rtl_work_func_t() to complete. Since rtl8152_close() is called by a
process holding rtnl_lock() which is requested by other processes, this
eventually leads to a system deadlock and crash.

Re-order the napi_disable() call to occur after the work function
disabling and urb cancellation calls are issued.

Change-Id: I6ef0b703fc214998a037a68f722f784e1d07815e
Reported-by: http://crbug.com/1017928Signed-off-by: NPrashant Malani <pmalani@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a malicious device gives a short MAC it can elicit up to
5 bytes of leaked memory out of the driver. We need to check for
ETH_ALEN instead.

Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.

Fixes: 332f989a ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those.

The QMI interface is exposed in USB configuration #1:

P:  Vendor=0489 ProdID=e0b4 Rev=03.18
S:  Manufacturer=FII
S:  Product=T77W968 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Acked-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Exactly same layout as the default DW5821e module, just a different
vid/pid.

The QMI interface is exposed in USB configuration #1:

P:  Vendor=413c ProdID=81e0 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5821e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: NAleksander Morgado <aleksander@aleksander.es>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.

V2: used sizeof as request by Alexander

Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.

The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.

Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.

BugLink: https://bugs.launchpad.net/bugs/1827961Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan78xx_status() will run with interrupts enabled due to the change in
ed194d13 ("usb: core: remove local_irq_save() around ->complete()
handler"). generic_handle_irq() expects to be run with IRQs disabled.

[    4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts
[    4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168
[    4.896294] 000: Modules linked in:
[    4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39
[    4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT)
[    4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO)
[    4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168
[    4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168
[    4.896339] 000: sp : ffff000010003cc0
[    4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060
[    4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b
[    4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400
[    4.896373] 000: x23: 000000000000004f x22: ffff000010003d64
[    4.896381] 000: x21: 0000000000000000 x20: 0000000000000002
[    4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060
[    4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb
[    4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465
[    4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0
[    4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08
[    4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920
[    4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00
[    4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510
[    4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000
[    4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000
[    4.896466] 000: Call trace:
[    4.896471] 000:  __handle_irq_event_percpu+0x154/0x168
[    4.896481] 000:  handle_irq_event_percpu+0x50/0xb0
[    4.896489] 000:  handle_irq_event+0x40/0x98
[    4.896497] 000:  handle_simple_irq+0xa4/0xf0
[    4.896505] 000:  generic_handle_irq+0x24/0x38
[    4.896513] 000:  intr_complete+0xb0/0xe0
[    4.896525] 000:  __usb_hcd_giveback_urb+0x58/0xd8
[    4.896533] 000:  usb_giveback_urb_bh+0xd0/0x170
[    4.896539] 000:  tasklet_action_common.isra.0+0x9c/0x128
[    4.896549] 000:  tasklet_hi_action+0x24/0x30
[    4.896556] 000:  __do_softirq+0x120/0x23c
[    4.896564] 000:  irq_exit+0xb8/0xd8
[    4.896571] 000:  __handle_domain_irq+0x64/0xb8
[    4.896579] 000:  bcm2836_arm_irqchip_handle_irq+0x60/0xc0
[    4.896586] 000:  el1_irq+0xb8/0x140
[    4.896592] 000:  arch_cpu_idle+0x10/0x18
[    4.896601] 000:  do_idle+0x200/0x280
[    4.896608] 000:  cpu_startup_entry+0x20/0x28
[    4.896615] 000:  rest_init+0xb4/0xc0
[    4.896623] 000:  arch_call_rest_init+0xc/0x14
[    4.896632] 000:  start_kernel+0x454/0x480

Fixes: ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler")
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stefan Wahren <wahrenst@gmx.net>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NDaniel Wagner <dwagner@suse.de>
Tested-by: NStefan Wahren <wahrenst@gmx.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the pointer rtl_fw->fw would be used before checking in
rtl8152_apply_firmware() that causes the following kernel oops.

Unable to handle kernel NULL pointer dereference at virtual address 00000002
pgd = (ptrval)
[00000002] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 131 Comm: kworker/0:2 Not tainted
5.4.0-rc1-00539-g9370f2d0 #6788
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events_long rtl_hw_phy_work_func_t
PC is at rtl8152_apply_firmware+0x14/0x464
LR is at r8153_hw_phy_cfg+0x24/0x17c
pc : [<c064f4e4>]    lr : [<c064fa18>]    psr: a0000013
sp : e75c9e60  ip : 60000013  fp : c11b7614
r10: e883b91c  r9 : 00000000  r8 : fffffffe
r7 : e883b640  r6 : fffffffe  r5 : fffffffe  r4 : e883b640
r3 : 736cfe7c  r2 : 736cfe7c  r1 : 000052f8  r0 : e883b640
Flags: NzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c5387d  Table: 6640006a  DAC: 00000051
Process kworker/0:2 (pid: 131, stack limit = 0x(ptrval))
Stack: (0xe75c9e60 to 0xe75ca000)
...
[<c064f4e4>] (rtl8152_apply_firmware) from [<c064fa18>]
(r8153_hw_phy_cfg+0x24/0x17c)
[<c064fa18>] (r8153_hw_phy_cfg) from [<c064e784>]
(rtl_hw_phy_work_func_t+0x220/0x3e4)
[<c064e784>] (rtl_hw_phy_work_func_t) from [<c0148a74>]
(process_one_work+0x22c/0x7c8)
[<c0148a74>] (process_one_work) from [<c0149054>] (worker_thread+0x44/0x520)
[<c0149054>] (worker_thread) from [<c0150548>] (kthread+0x130/0x164)
[<c0150548>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xe75c9fb0 to 0xe75c9ff8)
...

Fixes: 9370f2d0 ("r8152: support request_firmware for RTL8153")
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/lan78xx.c:3995:6: warning:
 variable event set but not used [-Wunused-but-set-variable]

It is never used, so can be removed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the firmware of PHY NC which is used to fix the issue found
for PHY. Currently, only RTL_VER_04, RTL_VER_05, and RTL_VER_06 need
it.

The order of loading PHY firmware would be

	RTL_FW_PHY_START
	RTL_FW_PHY_NC
	RTL_FW_PHY_STOP

The RTL_FW_PHY_START/RTL_FW_PHY_STOP are used to lock/unlock the PHY,
and set/clear the patch key from the firmware file.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Move r8153_patch_request() forward for later patch.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

Make sure @fw_offset field of struct fw_mac is more than the size
of struct fw_mac.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

The struct fw_type_1 is used by MAC only, so rename it to a meaningful one.

Besides, adjust two messages. Replace "load xxx fail" with "check xxx fail"
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>

This device is sold as 'ThinkPad USB-C Dock Gen 2 (40AS)'.
Chipset is RTL8153 and works with r8152.
Without this, the generic cdc_ether grabs the device, and the device jam
connected networks up when the machine suspends.
Signed-off-by: NKazutoshi Noguchi <noguchi.kazutosi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.

Change the order to close this race condition.

Fixes: 92571a1a ("lan78xx: Connect phy early")
Reported-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NDaniel Wagner <dwagner@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.

v2: fix syntax error
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch supports loading additional firmware file through
request_firmware().

A firmware file may include a header followed by several blocks
which have different types of firmware. Currently, the supported
types are RTL_FW_END, RTL_FW_PLA, and RTL_FW_USB.

The firmware is used to fix some compatible or hardware issues. For
example, the device couldn't be found after rebooting several times.

The supported chips are
	RTL_VER_04 (rtl8153a-2.fw)
	RTL_VER_05 (rtl8153a-3.fw)
	RTL_VER_06 (rtl8153a-4.fw)
	RTL_VER_09 (rtl8153b-2.fw)
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Reviewed-by: NPrashant Malani <pmalani@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>