Add support for the Asus Xonar DX.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix a (fortunately harmless) typo.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Change the card short name to show to show the card name instead of the
chip name.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When playing data at 96 kHz or higher, reduce the DAC oversampling rate
to 32.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the code that is common to all Xonar models to a separate function,
and make it more generic in preparation for another model.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Rename all CS5381 symbols to CS53x1 because they can also be used for
Xonar models with a CS5361.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use separate model structures for the D2 and D2X so that the init
function does not have to check for the model again.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add a function to write I2C registers.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly
like on Xonar cards, so move the Xonar code to the common mixer code.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Disable the master clock outputs of any unused I2S inputs.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Put the flag that enables the MIDI port into the model structure instead
of passing it as a separate parameter to oxygen_pci_probe().
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Allow the model drivers to specify if the codec communication goes over
SPI or a 2-wire bus.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

When specifying which PCM devices to use, model drivers now use flags
that also specify the routing between PCM devices and DMA channels
instead of just DMA channel bits.  This simplifies some code that checks
for these flags.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add controls to enable monitoring of the analog and digital inputs.

To allow monitoring after loading the driver when nothing has been
played back or recorded yet, the I2S input and outputs are initialized
to a valid configuration.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the PCM1796 register symbol definitions to their own header file.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Move the WM8786 register symbol definitions to their own header file.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Use priv_idx as an identifier.
sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one
sound/pci/oxygen/virtuoso.c:56:12: originally declared here
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

I forgot to set the module owner for the HiFier/Xonar models.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The GPIO pin 0 of the CM9780 must be set when muting the line input even
on non-Xonar cards.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Removed invalid __devinit and __devexit that are remaining after
split to a helper module.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

While the AK4396 and WM8785 datasheets say that the SPI clock cycle
length must be at least 200 ns, 320 ns seems not to work reliably with
the controller, so we better use 160 ns.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

On the Xonar D2X, monitor the GPIO pin that indicates whether external
power is present.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

When a second AC97 codec is present, add a PCM device for capturing from
the front panel.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add mixer controls for the front panel AC97 codec.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

After an AC97 register read or write, use the AC97 interrupt instead of
polling to wait for the access to be completed.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Move the line input switching code to the Virtuoso driver because only
the Xonar cards bypass the analog mixer for line input.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix the upper sample rate limit for the double rate mode of the AK4396
to the value from the datasheet.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a driver for the MediaTek/TempoTec HiFier Fantasia sound card.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Initialize more registers of the controller and the second AC97 codec.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a field to struct oxygen_model to allow model drivers for cards with
less than eight output channels.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

None of the reference design models have MIDI, only the X-Meridian
allows to connect a MIDI adapter.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix up SPDIF input sample rates again: 32 kHz and 64 kHz are not
supported.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add a mixer control for the SPDIF loopback function.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Add one more indirection to the lookup of the snd_pcm_hardware
structures so that we can save the space of the duplicate ones.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected.  This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Fix some wrong values for the definitions of the source masks for DACS 1
and 3.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Actually use the template that was maybe changed by the control filter
instead of the original one.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

According to the datasheets, the SPI clock cycle must be at least 200 ns
for the AK4396 and the WM8785, so we cannot use the default 160 ns.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>

Allow to record with 32 kHz, 64 kHz, 88.2 kHz and 176.4 kHz with cards
that have a WM8785 ADC.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJaroslav Kysela <perex@perex.cz>