Since VFs may be mapped to VMs which aren't trusted entities, flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that the specified QP number is assigned to that
VF.  Also, make sure to keep the QP busy till the end of the operation
from the resource tracker point of view.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Pull target updates from Nicholas Bellinger:
 "It has been a very busy development cycle this time around in target
  land, with the highlights including:

   - Kill struct se_subsystem_dev, in favor of direct se_device usage
     (hch)
   - Simplify reservations code by combining SPC-3 + SCSI-2 support for
     virtual backends only (hch)
   - Simplify ALUA code for virtual only backends, and remove left over
     abstractions (hch)
   - Pass sense_reason_t as return value for I/O submission path (hch)
   - Refactor MODE_SENSE emulation to allow for easier addition of new
     mode pages.  (roland)
   - Add emulation of MODE_SELECT (roland)
   - Fix bug in handling of ExpStatSN wrap-around (steve)
   - Fix bug in TMR ABORT_TASK lookup in qla2xxx target (steve)
   - Add WRITE_SAME w/ UNMAP=0 support for IBLOCK backends (nab)
   - Convert ib_srpt to use modern target_submit_cmd caller + drop
     legacy ioctx->kref usage (nab)
   - Convert ib_srpt to use modern target_submit_tmr caller (nab)
   - Add link_magic for fabric allow_link destination target_items for
     symlinks within target_core_fabric_configfs.c code (nab)
   - Allocate pointers in instead of full structs for
     config_group->default_groups (sebastian)
   - Fix 32-bit highmem breakage for FILEIO (sebastian)

  All told, hch was able to shave off another ~1K LOC by killing the
  se_subsystem_dev abstraction, along with a number of PR + ALUA
  simplifications.  Also, a nice patch by Roland is the refactoring of
  MODE_SENSE handling, along with the addition of initial MODE_SELECT
  emulation support for virtual backends.

  Sebastian found a long-standing issue wrt to allocation of full
  config_group instead of pointers for config_group->default_group[]
  setup in a number of areas, which ends up saving memory with big
  configurations.  He also managed to fix another long-standing BUG wrt
  to broken 32-bit highmem support within the FILEIO backend driver.

  Thank you again to everyone who contributed this round!"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
  target/iscsi_target: Add NodeACL tags for initiator group support
  target/tcm_fc: fix the lockdep warning due to inconsistent lock state
  sbp-target: fix error path in sbp_make_tpg()
  sbp-target: use simple assignment in tgt_agent_rw_agent_state()
  iscsi-target: use kstrdup() for iscsi_param
  target/file: merge fd_do_readv() and fd_do_writev()
  target/file: Fix 32-bit highmem breakage for SGL -> iovec mapping
  target: Add link_magic for fabric allow_link destination target_items
  ib_srpt: Convert TMR path to target_submit_tmr
  ib_srpt: Convert I/O path to target_submit_cmd + drop legacy ioctx->kref
  target: Make spc_get_write_same_sectors return sector_t
  target/configfs: use kmalloc() instead of kzalloc() for default groups
  target/configfs: allocate only 6 slots for dev_cg->default_groups
  target/configfs: allocate pointers instead of full struct for default_groups
  target: update error handling for sbc_setup_write_same()
  iscsit: use GFP_ATOMIC under spin lock
  iscsi_target: Remove redundant null check before kfree
  target/iblock: Forward declare bio helpers
  target: Clean up flow in transport_check_aborted_status()
  target: Clean up logic in transport_put_cmd()
  ...

Pull EXTCON patches from Greg Kroah-Hartman:
 "Here are some drivers/extcon/ patches that I forgot to have you pull
  in the larger char/misc patchset from yesterday, for the 3.8-rc1
  kernel.

  Nothing major here, just some driver updates, and cleanups, all of
  which have been in linux-next for a while now.

  Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"

* tag 'char-misc-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  extcon: kernel_doc style fix
  extcon: max77693: Fix uninitialised variable warning
  extcon: max77693: Use devm_kzalloc
  extcon: max8997: Use devm_kzalloc
  extcon: max8997: Fix a typo
  extcon: max8997: Fix checkpatch error
  extcon: max77693: Fix coding style
  extcon: max77693: Fix incorrect error check and return value
  extcon: max8997: Fix incorrect error check and return value
  extcon: Fix return value in extcon-class.c
  extcon: Add missing header file to extcon.h
  extcon: arizona: unlock mutex on error path in arizona_micdet()

Pull fbdev changes from Tomi Valkeinen:
 "OMAPDSS changes, including:
   - use dynanic debug prints
   - OMAP platform dependency removals
   - Creation of compat-layer, helping us to improve omapdrm
   - Misc cleanups, aiming to make omadss more in line with the upcoming
     common display framework

  Exynos DP changes for the 3.8 merge window:
   - Device Tree support for Samsung Exynos DP
   - SW Link training is cleaned up.
   - HPD interrupt is supported.

  Samsung Framebuffer changes for the 3.8 merge window:
   - The bit definitions of header file are updated.
   - Some minor typos are fixed.
   - Some minor bugs of s3c_fb_check_var() are fixed.

  FB related changes for SH Mobile, Freescale DIU

  Add support for the Solomon SSD1307 OLED Controller"

* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
  OMAPDSS: fix TV-out issue with DSI PLL
  Revert "OMAPFB: simplify locking"
  OMAPFB: remove silly loop in fb2display()
  OMAPFB: fix error handling in omapfb_find_best_mode()
  OMAPFB: use devm_kzalloc to allocate omapfb2_device
  OMAPDSS: DISPC: remove dispc fck uses
  OMAPDSS: DISPC: get dss clock rate from dss driver
  drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
  drivers/video: add support for the Solomon SSD1307 OLED Controller
  OMAPDSS: use omapdss_compat_init() in other drivers
  OMAPDSS: export dispc functions
  OMAPDSS: export dss_feat functions
  OMAPDSS: export dss_mgr_ops functions
  OMAPDSS: separate compat files in the Makefile
  OMAPDSS: move display sysfs init to compat layer
  OMAPDSS: DPI: use dispc's check_timings
  OMAPDSS: DISPC: add dispc_ovl_check()
  OMAPDSS: move irq handling to dispc-compat
  OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
  OMAPDSS: move blocking mgr enable/disable to compat layer
  ...

Conflicts:
	arch/arm/mach-davinci/devices-da8xx.c
	arch/arm/plat-omap/common.c
	drivers/media/platform/omap/omap_vout.c

Pull LED subsystem update from Bryan Wu.

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (47 commits)
  leds: leds-lp5521: return an error code on error in probe()
  leds: leds-clevo-mail: Use pr_* instead of printks
  leds: leds-rb532: Fix checkpatch errors
  leds: led-triggers: Fix checkpatch warnings
  leds: ledtrig-backlight: Fix checkpatch error
  leds: leds-wrap: Use <linux/io.h> instead of <asm/io.h>
  leds: leds-wm8350: Use dev_err instead of printk
  leds: leds-pwm: Fix checkpatch warning
  leds: leds-pca955x: Use dev_info instead of printk
  leds: leds-net48xx: Use linux/io.h instead of asm/io.h
  leds: leds-lt3593: Fix checkpatch warnings
  leds: leds-gpio: Use dev_info instead of printk
  leds: leds-da903x: Fix checkpatch error and warnings
  leds: leds-bd2802: Fix checkpatch warnings
  leds: leds-adp5520: Fix checkpatch warnings
  leds: led-class: Fix checkpatch warning
  leds: leds-ns2: use devm_gpio_request_one
  leds: leds-lt3593: use devm_gpio_request_one
  leds: leds-gpio: use devm_gpio_request_one
  leds: lp3944: Fix return value
  ...

Pull pstore update from Anton Vorontsov:
 "Here are just a few fixups for the pstore subsystem, nothing special
  this time"

* tag 'for-v3.8' of git://git.infradead.org/users/cbou/linux-pstore:
  pstore/ftrace: Adjust for ftrace_ops->func prototype change
  pstore/ram: Fix bounds checks for mem_size, record_size, console_size and ftrace_size
  pstore/ram: Fix undefined usage of rounddown_pow_of_two(0)
  pstore/ram: Fixup section annotations

Pull libata updates from Jeff Garzik:

 - More ACPI fixes

 - ata_piix: cosmetic code movement, re-enable MS Virtual PC support

 - generic platform driver improvements; use common code

 - pata_cs5536: add quirk for broken udma

 - printk prettiness (dev_printk becomes dev_info, etc.)

 - sata_promise: fix hardreset lockdep error

 - minor cleanups from Sergei Shtylyov

 - minor, automated cleanups from Wei Yongjun

 - fix null ptr deref bug, in sysfs API

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (37 commits)
  sata_dwc_460ex: remove file exec bit (chmod 0755 -> 0644)
  [libata] fix Null pointer dereference on disk error
  ahci: convert ata_link_printk() to ata_link_warn()
  pata_imx: convert ata_dev_printk() to ata_dev_info()
  ARM: ep93xx: convert ata_<foo>_printk() to ata_<foo>_<level>()
  ahci_platform: make structs static
  Revert "pata_octeon_cf: perform host detach, removal on exit"
  Revert "libata: check SATA_SETTINGS log with HW Feature Ctrl"
  pata_of_platform: fix compile error
  libata: use pci_get_drvdata() helper
  pata_octeon_cf: perform host detach, removal on exit
  sata_highbank: utilize common ata_platform_remove_one()
  pata_palmld: utilize common ata_platform_remove_one()
  pata_platform: remove unused remove function
  pata_platform: utilize common ata_platform_remove_one()
  pata_of_platform: utilize common ata_platform_remove_one()
  pata_mpc52xx: utilize common ata_platform_remove_one()
  pata_ixp4xx_cf: utilize common ata_platform_remove_one()
  ahci_platform: utilize common ata_platform_remove_one()
  libata: implement ata_platform_remove_one()
  ...

Pull microblaze update from Michal Simek:
 "The main change is UAPI for Microblaze."

* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: signal: Declare do_notify_resume
  microblaze: lib: Add lib function declarations
  microblaze: lib: Remove helper macros
  microblaze: Add static qualifiers
  microblaze: Wire-up new system call kcmp
  microblaze: Fix intc_enable_or_unmask function
  microblaze: Do not initialized regs->r1 twice in ELF_PLAT_INIT
  microblaze: Remove passing the second arg to schedule_tail
  UAPI: (Scripted) Disintegrate arch/microblaze/include/asm
  microblaze: uaccess.h: Fix timerfd syscall
  microblaze: Remove BIP from childregs

Pull crypto update from Herbert Xu:

 - Added aesni/avx/x86_64 implementations for camellia.

 - Optimised AVX code for cast5/serpent/twofish/cast6.

 - Fixed vmac bug with unaligned input.

 - Allow compression algorithms in FIPS mode.

 - Optimised crc32c implementation for Intel.

 - Misc fixes.

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (32 commits)
  crypto: caam - Updated SEC-4.0 device tree binding for ERA information.
  crypto: testmgr - remove superfluous initializers for xts(aes)
  crypto: testmgr - allow compression algs in fips mode
  crypto: testmgr - add larger crc32c test vector to test FPU path in crc32c_intel
  crypto: testmgr - clean alg_test_null entries in alg_test_descs[]
  crypto: testmgr - remove fips_allowed flag from camellia-aesni null-tests
  crypto: cast5/cast6 - move lookup tables to shared module
  padata: use __this_cpu_read per-cpu helper
  crypto: s5p-sss - Fix compilation error
  crypto: picoxcell - Add terminating entry for platform_device_id table
  crypto: omap-aes - select BLKCIPHER2
  crypto: camellia - add AES-NI/AVX/x86_64 assembler implementation of camellia cipher
  crypto: camellia-x86_64 - share common functions and move structures and function definitions to header file
  crypto: tcrypt - add async speed test for camellia cipher
  crypto: tegra-aes - fix error-valued pointer dereference
  crypto: tegra - fix missing unlock on error case
  crypto: cast5/avx - avoid using temporary stack buffers
  crypto: serpent/avx - avoid using temporary stack buffers
  crypto: twofish/avx - avoid using temporary stack buffers
  crypto: cast6/avx - avoid using temporary stack buffers
  ...

Pull GFS2 updates from Steven Whitehouse:
 "The main feature this time is the new Orlov allocator and the patches
  leading up to it which allow us to allocate new inodes from their own
  allocation context, rather than borrowing that of their parent
  directory.  It is this change which then allows us to choose a
  different location for subdirectories when required.  This works
  exactly as per the ext3 implementation from the users point of view.

  In addition to that, we've got a speed up in gfs2_rbm_from_block()
  from Bob Peterson, three locking related improvements from Dave
  Teigland plus a selection of smaller bug fixes and clean ups."

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
  GFS2: Set gl_object during inode create
  GFS2: add error check while allocating new inodes
  GFS2: don't reference inode's glock during block allocation trace
  GFS2: remove redundant lvb pointer
  GFS2: only use lvb on glocks that need it
  GFS2: skip dlm_unlock calls in unmount
  GFS2: Fix one RG corner case
  GFS2: Eliminate redundant buffer_head manipulation in gfs2_unlink_inode
  GFS2: Use dirty_inode in gfs2_dir_add
  GFS2: Fix truncation of journaled data files
  GFS2: Add Orlov allocator
  GFS2: Use proper allocation context for new inodes
  GFS2: Add test for resource group congestion status
  GFS2: Rename glops go_xmote_th to go_sync
  GFS2: Speed up gfs2_rbm_from_block
  GFS2: Review bug traps in glops.c

This reverts commit 53b87cf0.

It causes odd bootup problems on x86-64.  Markus Trippelsdorf gets a
repeatable oops, and I see a non-repeatable oops (or constant stream of
messages that scroll off too quickly to read) that seems to go away with
this commit reverted.

So we don't know exactly what is wrong with the commit, but it's
definitely problematic, and worth reverting sooner rather than later.
Bisected-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Cc: H Peter Anvin <hpa@zytor.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull x86 UAPI disintegration from David Howells.

This is the scripted disintegration of the uapi headers for x86, now
that most of the x86 updates for 3.8 are hopefully merged.

* tag 'disintegrate-x86-20121214' of git://git.infradead.org/users/dhowells/linux-headers:
  UAPI: (Scripted) Disintegrate arch/x86/include/asm

Pull another devicetree update from Grant Likely:
 "Here's a couple more devicetree changes that I missed in the first
  pull by putting the tag in the wrong place.

  Two minor devicetree fixups for v3.8.  Addition of dummy inlines and
  constification of node argument to of_parse_phandle_with_args()."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  of: *node argument to of_parse_phandle_with_args should be const
  of/i2c: add dummy inline functions for when CONFIG_OF_I2C(_MODULE) isn't defined

Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
 "This is a branch with updates for Marvell's mvebu/kirkwood platforms.
  They came in late-ish, and were heavily interdependent such that it
  didn't make sense to split them up across the cross-platform topic
  branches.  So here they are (for the second release in a row) in a
  branch on their own."

* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
  arm: l2x0: add aurora related properties to OF binding
  arm: mvebu: add Aurora L2 Cache Controller to the DT
  arm: mvebu: add L2 cache support
  dma: mv_xor: fix error handling path
  dma: mv_xor: fix error checking of irq_of_parse_and_map()
  dma: mv_xor: use request_irq() instead of devm_request_irq()
  dma: mv_xor: clear the window override control registers
  arm: mvebu: fix address decoding armada_cfg_base() function
  ARM: mvebu: update defconfig with I2C and RTC support
  ARM: mvebu: Add SATA support for OpenBlocks AX3-4
  ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
  ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
  ARM: mvebu: Add support for I2C controllers in Armada 370/XP
  arm: mvebu: Add hardware I/O Coherency support
  arm: plat-orion: Add coherency attribute when setup mbus target
  arm: dma mapping: Export a dma ops function arm_dma_set_mask
  arm: mvebu: Add SMP support for Armada XP
  arm: mm: Add support for PJ4B cpu and init routines
  arm: mvebu: Add IPI support via doorbells
  arm: mvebu: Add initial support for power managmement service unit
  ...

Pull ARM SoC device-tree updates, take 2, from Olof Johansson:
 "This branch contains device-tree updates for the SPEAr platform.  They
  had dependencies on earlier branches from this merge window, which is
  why they were broken out in a separate branch."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: SPEAr3xx: Shirq: Move shirq controller out of plat/
  ARM: SPEAr320: DT: Add SPEAr 320 HMI board support
  ARM: SPEAr3xx: DT: add shirq node for interrupt multiplexor
  ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT
  ARM: SPEAr1310: Fix AUXDATA for compact flash controller
  ARM: SPEAr13xx: Remove fields not required for ssp controller
  ARM: SPEAr1310: Move 1310 specific misc register into machine specific files
  ARM: SPEAr: DT: Update device nodes
  ARM: SPEAr: DT: add uart state to fix warning
  ARM: SPEAr: DT: Modify DT bindings for STMMAC
  ARM: SPEAr: DT: Fix existing DT support
  ARM: SPEAr: DT: Update partition info for MTD devices
  ARM: SPEAr: DT: Update pinctrl list
  ARM: SPEAr13xx: DT: Add spics gpio controller nodes

Pull ARM Soc updates, take 2, from Olof Johansson:
 "This is the second batch of SoC updates for the 3.8 merge window,
  containing parts that had dependencies on earlier branches such that
  we couldn't include them with the first branch.

  These are general updates for Samsung Exynos, Renesas/shmobile and a
  topic branch that adds SMP support to Altera's socfpga platform."

Fix up conflicts mostly as per Olof.

* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: EXYNOS: Clock settings for SATA and SATA PHY
  ARM: EXYNOS: Add ARM down clock support
  ARM: EXYNOS: Fix i2c suspend/resume for legacy controller
  ARM: EXYNOS: Add aliases for i2c controller
  ARM: EXYNOS: Setup legacy i2c controller interrupts
  sh: clkfwk: fixup unsed variable warning
  Revert "ARM: shmobile: r8a7779: Replace modify_scu_cpu_psr with scu_power_mode"
  Revert "ARM: shmobile: sh73a0: Replace modify_scu_cpu_psr with scu_power_mode"
  Revert "ARM: shmobile: emev2: Replace modify_scu_cpu_psr with scu_power_mode"
  ARM: highbank: use common debug_ll_io_init
  ARM: shmobile: sh7372: sh7372_fsiXck_clk become non-global
  ARM: shmobile: sh7372: remove fsidivx clock
  ARM: socfpga: mark secondary_trampoline as cpuinit
  socfpga: map uart into virtual address space so that early_printk() works
  ARM: socfpga: fix build break for allyesconfig
  ARM: socfpga: Enable SMP for socfpga
  ARM: EXYNOS: Add dp clock support for EXYNOS5
  ARM: SAMSUNG: call clk_get_rate for debugfs rate files
  ARM: SAMSUNG: add clock_tree debugfs file in clock

Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Kerrisk <mtk.manpages@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: NDave Jones <davej@redhat.com>

Pull MIPS updates from Ralf Baechle:
 "The MIPS bits for 3.8.  This also includes a bunch fixes that were
  sitting in the linux-mips.org git tree for a long time.  This pull
  request contains updates to several OCTEON drivers and the board
  support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
  updates to the SSB bus support, MIPS kexec code and adds support for
  kdump.

  When pulling this, there are two expected merge conflicts in
  include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
  resolve, just remove the conflict markers and keep both alternatives."

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
  MIPS: PMC-Sierra Yosemite: Remove support.
  VIDEO: Newport Fix console crashes
  MIPS: wrppmc: Fix build of PCI code.
  MIPS: IP22/IP28: Fix build of EISA code.
  MIPS: RB532: Fix build of prom code.
  MIPS: PowerTV: Fix build.
  MIPS: IP27: Correct fucked grammar in ops-bridge.c
  MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
  MIPS: Fix potencial corruption
  MIPS: Fix for warning from FPU emulation code
  MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
  MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
  MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
  MIPS: Remove unused smvp.h
  MIPS/EDAC: Improve OCTEON EDAC support.
  MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
  MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
  ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
  MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
  MIPS: Remove usage of CEVT_R4K_LIB config option.
  ...

Merging in the smp-on-socfpga branch into soc2 since the topics are similar
and it's a short branch in the first place.

* next/smp:
  ARM: socfpga: mark secondary_trampoline as cpuinit
  socfpga: map uart into virtual address space so that early_printk() works
  ARM: socfpga: fix build break for allyesconfig
  ARM: socfpga: Enable SMP for socfpga
Signed-off-by: NOlof Johansson <olof@lixom.net>

Pull x86 EFI update from Peter Anvin:
 "EFI tree, from Matt Fleming.  Most of the patches are the new efivarfs
  filesystem by Matt Garrett & co.  The balance are support for EFI
  wallclock in the absence of a hardware-specific driver, and various
  fixes and cleanups."

* 'core-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  efivarfs: Make efivarfs_fill_super() static
  x86, efi: Check table header length in efi_bgrt_init()
  efivarfs: Use query_variable_info() to limit kmalloc()
  efivarfs: Fix return value of efivarfs_file_write()
  efivarfs: Return a consistent error when efivarfs_get_inode() fails
  efivarfs: Make 'datasize' unsigned long
  efivarfs: Add unique magic number
  efivarfs: Replace magic number with sizeof(attributes)
  efivarfs: Return an error if we fail to read a variable
  efi: Clarify GUID length calculations
  efivarfs: Implement exclusive access for {get,set}_variable
  efivarfs: efivarfs_fill_super() ensure we clean up correctly on error
  efivarfs: efivarfs_fill_super() ensure we free our temporary name
  efivarfs: efivarfs_fill_super() fix inode reference counts
  efivarfs: efivarfs_create() ensure we drop our reference on inode on error
  efivarfs: efivarfs_file_read ensure we free data in error paths
  x86-64/efi: Use EFI to deal with platform wall clock (again)
  x86/kernel: remove tboot 1:1 page table creation code
  x86, efi: 1:1 pagetable mapping for virtual EFI calls
  x86, mm: Include the entire kernel memory map in trampoline_pgd
  ...

Pull x86 ACPI update from Peter Anvin:
 "This is a patchset which didn't make the last merge window.  It adds a
  debugging capability to feed ACPI tables via the initramfs.

  On a grander scope, it formalizes using the initramfs protocol for
  feeding arbitrary blobs which need to be accessed early to the kernel:
  they are fed first in the initramfs blob (lots of bootloaders can
  concatenate this at boot time, others can use a single file) in an
  uncompressed cpio archive using filenames starting with "kernel/".

  The ACPI maintainers requested that this patchset be fed via the x86
  tree rather than the ACPI tree as the footprint in the general x86
  code is much bigger than in the ACPI code proper."

* 'x86-acpi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  X86 ACPI: Use #ifdef not #if for CONFIG_X86 check
  ACPI: Fix build when disabled
  ACPI: Document ACPI table overriding via initrd
  ACPI: Create acpi_table_taint() function to avoid code duplication
  ACPI: Implement physical address table override
  ACPI: Store valid ACPI tables passed via early initrd in reserved memblock areas
  x86, acpi: Introduce x86 arch specific arch_reserve_mem_area() for e820 handling
  lib: Add early cpio decoder

Pull x86 RAS update from Ingo Molnar:
 "Rework all config variables used throughout the MCA code and collect
  them together into a mca_config struct.  This keeps them tightly and
  neatly packed together instead of spilled all over the place.

  Then, convert those which are used as booleans into real booleans and
  save some space.  These bits are exposed via
     /sys/devices/system/machinecheck/machinecheck*/"

* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, MCA: Finish mca_config conversion
  x86, MCA: Convert the next three variables batch
  x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
  x86, MCA: Convert dont_log_ce, banks and tolerant
  drivers/base: Add a DEVICE_BOOL_ATTR macro

This reverts commit f269ae04.

It turns out it causes a very noticeable interactivity regression with
CONFIG_SCHED_AUTOGROUP (test-case: "make -j32" of the kernel in a
terminal window, while scrolling in a browser - the autogrouping means
that the two end up in separate cgroups, and the browser should be
smooth as silk despite the high load).

Says Paul Turner:
 "It seems that the update-throttling on the wake-side is reducing the
  interactive tasks' ability to preempt.  While I suspect the right
  longer term answer here is force these updates only in the
  cross-cgroup case; this is less trivial.  For this release I believe
  the right answer is either going to be a revert or restore the updates
  on the enqueue-side."
Reported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Bisected-by: NMike Galbraith <efault@gmx.de>
Acked-by: NPaul Turner <pjt@google.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Following oops were observed when disk error happened:

[ 4272.896937] sd 0:0:0:0: [sda] Unhandled error code
[ 4272.896939] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 4272.896942] sd 0:0:0:0: [sda] CDB: Read(10): 28 00 00 5a de a7 00 00 08 00
[ 4272.896951] end_request: I/O error, dev sda, sector 5955239
[ 4291.574947] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4291.658305] IP: [] ahci_activity_show+0x1/0x40
[ 4291.730090] PGD 76dbbc067 PUD 6c4fba067 PMD 0
[ 4291.783408] Oops: 0000 [#1] SMP
[ 4291.822100] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/sw_activity
[ 4291.934235] CPU 9
[ 4291.958301] Pid: 27942, comm: hwinfo ......

ata_scsi_find_dev could return NULL, so ata_scsi_activity_{show,store} should check if atadev is NULL.
Signed-off-by: NXiaotian Feng <dannyfeng@tencent.com>
Cc: James Bottomley <JBottomley@Parallels.com>
Cc: stable@kernel.org
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Using ata_link_warn() instead of ata_link_printk().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Using ata_dev_info() instead of ata_dev_printk().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Using ata_<foo>_<level>() instead of ata_<foo>_printk().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

These structs are used only for ahci_platform.c, so they should be
static. Thanks to Fengguang for the (automated) suggestion.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This reverts commit 1645bf1b.

Brian Norris writes:
  > David Daney writes:

  > I can seem to find it.  Without knowing what that does, I would be inclined
  > to NACK the whole thing.

  A NACK is probably the right thing. I was mostly converting a few
  other drivers which used some simple, common patterns to use my new
  common code, but this driver was missing it altogether. It looks like
  there may be bigger issues, though, as you point out.

  > This patch is likely to be incomplete as the driver is also missing the
  > module_exit() things.
  >
  > It might be simpler to just make the driver "bool" instead of "tristate" in
  > the Kconfig.

  As noted earlier, I don't have much interest in this driver. I agree
  that there are some other issues with the driver; I think it leaks
  memory if it is ever allowed to unload, for one. Feel free to submit
  an alternative patch to prevent this driver from being built as a
  module.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This reverts commit de90cd71.

Shane Huang writes:

  Please suspend this patch because I just received two new
  DevSlp drives but found word 78 bit 5 is _not_ set.

  I'm checking with the drive vendor whether he gave me
  the wrong information. If bit 5 is not the necessary and
  sufficient condition, I will implement another patch to
  replace ata_device->sata_settings into ->devslp_timing.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Pull battery subsystem updates from Anton Vorontsov:
 "Highlights:

   - Two new drivers from Pali Rohár and N900 hackers: rx51_battery and
     bq2415x_charger.  The drivers are a part of a solution to replace
     the proprietary Nokia BME stack

   - Power supply core now registers devices with a thermal cooling
     subsystem, so we can now automatically throttle charging.  Thanks
     to Ramakrishna Pallala!

   - Device tree support for ab8500 and max8925_power drivers

   - Random fixups and enhancements for a bunch of drivers."

* tag 'for-v3.8-merged' of git://git.infradead.org/battery-2.6: (22 commits)
  max8925_power: Add support for device-tree initialization
  ab8500: Add devicetree support for chargalg
  ab8500: Add devicetree support for charger
  ab8500: Add devicetree support for btemp
  ab8500: Add devicetree support for fuelgauge
  twl4030_charger: Change TWL4030_MODULE_* ids to TWL_MODULE_*
  jz4740-battery: Use devm_request_and_ioremap
  jz4740-battery: Use devm_kzalloc
  bq27x00_battery: Fixup nominal available capacity reporting
  bq2415x_charger: Fix style issues
  bq2415x_charger: Add Kconfig/Makefile entries
  power_supply: Add bq2415x charger driver
  power_supply: Add new Nokia RX-51 (N900) power supply battery driver
  max17042_battery: Fix missing verify_model_lock() return value check
  ds2782_battery: Fix signedness bug in ds278x_read_reg16()
  lp8788-charger: Fix ADC channel names
  lp8788-charger: Fix wrong ADC conversion
  lp8788-charger: Use consumer device name on setting IIO channels
  power_supply: Register power supply for thermal cooling device
  power_supply: Add support for CHARGE_CONTROL_* attributes
  ...

Pull media updates from Mauro Carvalho Chehab:

 - Missing MAINTAINERS entries were added for several drivers

 - Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
   sharing between V4L2 devices and GPU

 - Got rid of all warnings when compiling with W=1 on x86

 - Add a new driver for Exynos hardware (s3c-camif)

 - Several bug fixes, cleanups and driver improvements

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
  [media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
  [media] omap3isp: Prepare/unprepare clocks before/after enable/disable
  [media] omap3isp: preview: Add support for 8-bit formats at the sink pad
  [media] omap3isp: Replace printk with dev_*
  [media] omap3isp: Find source pad from external entity
  [media] omap3isp: Configure CSI-2 phy based on platform data
  [media] omap3isp: Add PHY routing configuration
  [media] omap3isp: Add CSI configuration registers from control block to ISP resources
  [media] omap3isp: Remove unneeded module memory address definitions
  [media] omap3isp: Use monotonic timestamps for statistics buffers
  [media] uvcvideo: Fix control value clamping for unsigned integer controls
  [media] uvcvideo: Mark first output terminal as default video node
  [media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
  [media] uvcvideo: Return -ENOTTY for unsupported ioctls
  [media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
  [media] uvcvideo: Don't fail when an unsupported format is requested
  [media] uvcvideo: Return -EACCES when trying to access a read/write-only control
  [media] uvcvideo: Set error_idx properly for extended controls API failures
  [media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
  [media] fc2580: write some registers conditionally
  ...

Pull first round of SCSI updates from James Bottomley:
 "This patch set includes two large new drivers: mpt3sas (for the next
  gen fusion SAS hardware) and csiostor a FCoE offload driver for the
  Chelsio converged network cards (this includes some net changes which
  I've OK'd with DaveM).

  The rest of the patch is driver updates (qla2xxx, lpfc, hptiop,
  be2iscsi) plus a few assorted updates and bug fixes.

  We also have a Power Management rework in the Upper Layer Drivers
  preparatory to doing ACPI zero power optical devices, but the actual
  enabler is still being worked on.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (72 commits)
  [SCSI] mpt3sas: add new driver supporting 12GB SAS
  [SCSI] scsi_transport_sas: add 12GB definitions for mpt3sas
  [SCSI] miscdevice: Adding support for MPT3SAS_MINOR(222)
  [SCSI] csiostor: remove unneeded memset()
  [SCSI] csiostor: Fix sparse warnings.
  [SCSI] qla2xxx: Display that driver is operating in legacy interrupt mode.
  [SCSI] qla2xxx: Dont clear drv active on iospace config failure.
  [SCSI] qla2xxx: Fix typo in qla2xxx driver.
  [SCSI] qla2xxx: Update ql2xextended_error_logging parameter description with new option.
  [SCSI] qla2xxx: Parameterize the link speed of hba rather than fcport.
  [SCSI] qla2xxx: Add 16Gb/s case to get port speed capability.
  [SCSI] qla2xxx: Move marking fcport online ahead of setting iiDMA speed.
  [SCSI] qla2xxx: Add acquiring of risc semaphore before doing ISP reset.
  [SCSI] qla2xxx: Ignore driver ack bit if corresponding presence bit is not set.
  [SCSI] qla2xxx: Fix typo in qla83xx_fw_dump function.
  [SCSI] qla2xxx: Add Gen3 PCIe speed 8GT/s to the log message.
  [SCSI] qla2xxx: Use correct Request-Q-Out register during bidirectional request processing
  [SCSI] qla2xxx: Move noisy Start scsi failed messages to verbose logging level.
  [SCSI] qla2xxx: Fix coccinelle warnings in qla2x00_relogin.
  [SCSI] qla2xxx: No fcport FC-4 type assignment in GA_NXT response.
  ...

Pull infiniband upate from Roland Dreier:
 "First batch of InfiniBand/RDMA changes for the 3.8 merge window:
   - A good chunk of Bart Van Assche's SRP fixes
   - UAPI disintegration from David Howells
   - mlx4 support for "64-byte CQE" hardware feature from Or Gerlitz
   - Other miscellaneous fixes"

Fix up trivial conflict in mellanox/mlx4 driver.

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (33 commits)
  RDMA/nes: Fix for crash when registering zero length MR for CQ
  RDMA/nes: Fix for terminate timer crash
  RDMA/nes: Fix for BUG_ON due to adding already-pending timer
  IB/srp: Allow SRP disconnect through sysfs
  srp_transport: Document sysfs attributes
  srp_transport: Simplify attribute initialization code
  srp_transport: Fix attribute registration
  IB/srp: Document sysfs attributes
  IB/srp: send disconnect request without waiting for CM timewait exit
  IB/srp: destroy and recreate QP and CQs when reconnecting
  IB/srp: Eliminate state SRP_TARGET_DEAD
  IB/srp: Introduce the helper function srp_remove_target()
  IB/srp: Suppress superfluous error messages
  IB/srp: Process all error completions
  IB/srp: Introduce srp_handle_qp_err()
  IB/srp: Simplify SCSI error handling
  IB/srp: Keep processing commands during host removal
  IB/srp: Eliminate state SRP_TARGET_CONNECTING
  IB/srp: Increase block layer timeout
  RDMA/cm: Change return value from find_gid_port()
  ...

Pull SPI updates from Grant Likely:
 "Primarily SPI device driver bug fixes, one removal of an old driver,
  and some new tegra support.  There is some core code change too, but
  all in all pretty small stuff.

  The new features to note are:
   - Common code for describing GPIO CS lines in the device tree
   - Remove the SPI_BUFSIZ limitation on spi_write_the_read()
   - core spi ensures bits_per_word is set correctly
   - SPARC can now use SPI"

* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
  spi/sparc: Allow of_register_spi_devices for sparc
  spi: Remove HOTPLUG section attributes
  spi: Add support for specifying 3-wire mode via device tree
  spi: Fix comparison of different integer types
  spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
  spi/sh: Add SH Mobile series as dependency to MSIOF controller
  spi/sh-msiof: Remove unneeded clock name
  spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
  spi/stmp: remove obsolete driver
  spi/clps711x: New SPI master driver
  spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
  spi: omap2-mcspi: Fix the redifine warning
  spi/sh-hspi: add CS manual control support
  of_spi: add generic binding support to specify cs gpio
  spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
  spi/bitbang: (cosmetic) simplify list manipulation
  spi/bitbang: avoid needless loop flow manipulations
  spi/omap: fix D0/D1 direction confusion
  spi: tegra: add spi driver for sflash controller
  spi: Dont call master->setup if not populated
  ...

Merge emailed autofs cleanup/fix patches from Ian Kent

* autofs:
  autofs4 - use simple_empty() for empty directory check
  autofs4 - dont clear DCACHE_NEED_AUTOMOUNT on rootless mount

For direct (and offset) mounts, if an automounted mount is manually
umounted the trigger mount dentry can appear non-empty causing it to
not trigger mounts. This can also happen if there is a file handle
leak in a user space automounting application.

This happens because, when a ioctl control file handle is opened
on the mount, a cursor dentry is created which causes list_empty()
to see the dentry as non-empty. Since there is a case where listing
the directory of these dentrys is needed, the use of dcache_dir_*()
functions for .open() and .release() is needed.

Consequently simple_empty() must be used instead of list_empty()
when checking for an empty directory.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The DCACHE_NEED_AUTOMOUNT flag is cleared on mount and set on expire
for autofs rootless multi-mount dentrys to prevent unnecessary calls
to ->d_automount().

Since DCACHE_MANAGE_TRANSIT is always set on autofs dentrys ->d_managed()
is always called so the check can be done in ->d_manage() without the
need to change the flag. This still avoids unnecessary calls to
->d_automount(), adds negligible overhead and eliminates a seriously
ugly check in the expire code.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ktest update from Steven Rostedt:
 "fixes and updated for new boot loaders"

* tag 'ktest-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Test if target machine is up before install
  ktest: Fix breakage from change of oldnoconfig to olddefconfig
  ktest: Add native support for syslinux boot loader
  ktest: Sync before reboot
  ktest: Add support for grub2