DWC3 controller curretly depends on USB && USB_GADGET.
Some hardware may like to use only host feature on dwc3,
or only gadget feature.

So, removing this dependency of USB_DWC3 on USB and USB_GADGET.
Adding the mode of operaiton of DWC3 also here
HOST/GADGET/DUAL_ROLE based on which features are enabled.

[ balbi@ti.com :
	. make sure we have default modes for all possible Kernel
		configurations.
	. Remove the config -> menuconfig change as it's unnecessary
	. switch over to IS_ENABLED() ]

CC: Doug Anderson <dianders@chromium.org>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To work with scatter gather properly, fixes have been done in number of
functions. I will explain requirement of each fixes one by one.

start_slot: used to retrieve all request of SG during cleanup

dwc3_gadget_giveback: We need to skip link TRB if it was one of the
intermediate TRB of SG.

dwc3_prepare_one_trb: We need to track all submitted TRBs during
cleanup. Since, all TRBs would be serially allocated, so we can just
keep starting slot info and we can always find rest of them. We need to
pass sg node number, so that we cab appropriately program ISOC_FIRST/ISOC,
Chain etc.

dwc3_prepare_trbs: last_one should be set when it is last node
of SG as well as last node of request_list.

__dwc3_cleanup_done_trbs: It has been prepared after re-factorization of
dwc3_cleanup_done_reqs. It is called for each TRB of SG.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two reasons to generate missed isoc.

1. when the host does not poll for all the data.
2. because of application-side delays that prevent all the data from
being transferred in programmed microframe.

Current code was able to handle first case only.  This patch handles
scenario 2 as well.Scenario 2 sometime may occur with complex gadget
application, however it can be easily reproduced for testing purpose as
follows:

a. use isoc binterval as 1 in f_sourcesink.
b. use pattern=0
c. introduce a delay of 150us deliberately in source_sink_complete, so
that after few frames it lands into scenario 2.
d. now run testusb 16 (isoc in  test). You will notice that if this
patch is not applied then isoc transfer is not able to recover after
first missed.

Current patch's approach is as under:

If missed isoc occurs and there is no request queued then issue END
TRANSFER, so that core generates next xfernotready and we will issue a
fresh START TRANSFER.
If there are still queued request then wait, do not issue either END or
UPDATE TRANSFER, just attach next request in request_list during giveback.
If any future queued request is successfully transferred then we will issue
UPDATE TRANSFER for all request in the request_list.

Cc: <stable@vger.kernel.org> # v3.6 v3.7 v3.8
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

regset is a generic implementation of regdump
utility through debugfs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Currently we're allocating an entire page to
serve as our event buffer. Provided our events
are 4 bytes long, it's very unlikely we will
even trigger 1k events at once.

Even in the worst case scenario where every
endpoint triggers one event and we still have
a couple of error events, that would still
be less than 40 events.

In order to cope with future versions of the
IP which could (or could not) increase the
amount of possible events to trigger
simultaneously, we're using an arbitrary size
of 64 events for our event buffer.

We're saving 3840 bytes by doing so.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The lockless implementation of the unique id is quite impressive (:P)
but dirver's core can handle it, we can remove it and make our code a
little smaller.

Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will let us control PHYs on platforms which
need them.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There's no such thing as XferNotReady(SETUP), we
can safely drop all that code with no problems
whatsoever.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

resource_index is more human readable. No
functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The definition of DWC3_DCTL_HIRD_THRES macro is
completely wrong. It will only work for when we
want to read the register's contents for that bitfield.

Change the macro so that it can be used to writing to
the register, and when we need to read, we can add
extra right shift of 24 bits.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>

[ balbi@ti.com: add a commit log ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If an IN transfer is missed on isoc endpoint, then driver must insure
that next ep_queue is properly handled.
This patch fixes this issue by starting a new transfer for next queued
request.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

SOF Number is bit16:3 of DSTS. Correct the mask accordingly.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Correct  define for DWC3_TRB_SIZE_TRBSTS.
Signed-off-by: NPratyush Anand <pratyush.anand@st.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds definitions for some new registers that have been
added to later versions of the controller, up to v2.10a.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove redundant pointer to struct usb_endpoint_descriptor.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

to avoid sprinkling magic constants on the driver
we define a constant to be used when allocating
setup_buffer and ep0_bounce buffer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is basically a noop for DWC3. We don't have
to do anything. Basically we test if the request
parameters are correct, cache the Isochronous
Delay and return success.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch implements Set SEL Standard Request
support for dwc3 driver. It needs to issue a command
to the controller passing the timing we received on
the data phase of the Set SEL request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will be used by the ep0 layer for implementing
Set SEL Standard Request.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On device loading the driver enables LPM and the acceptance of U1 and U2
states. The [Set|Clear]Feature requests for "U1/U2" are forwarded
directly to the hardware and allow / forbid the initiation of the low
power links.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This fix prevents a problem with dwc3 and host mode where
we were requesting the entire memory region in dwc3/core.c,
thus preventing xhci-plat from ever ioremapping its own address space.
Signed-off-by: NIdo Shayevitz <idos@codeaurora.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We have other revisions already released, let's
define revision macros for those so we can do
runtime detection of known erratas.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Define DWC3_GCTL_SCALEDOWN_MASK and use it in place of
DWC3_GCTL_SCALEDOWN(3).
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

trivial patch, no functional changes
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

those routines have everything we need to map/unmap
USB requests and it's better to use them.

In order to achieve that, we had to add a simple
change on how we allocate and use our setup buffer;
we cannot allocate it from coherent anymore otherwise
the generic map/unmap routines won't be able to easily
know that the GetStatus request already has a DMA
address.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will get rid of a useless memcpy on
IRQ handling, thus improving driver performance.

Tested with OMAP5430 running g_mass_storage on
SuperSpeed and HighSpeed.

Note that we are removing the little endian access
of the TRB and all accesses will be in System endianness,
if there happens to be a system in BE, bit 12 of GSBUSCFG0
should be set so that HW does byte invariant BE accesses
when fetching TRBs.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When host requests us to enter a test mode,
we cannot directly enter the test mode before
Status Phase is completed, otherwise the core
will never be able to deliver the Status ZLP
to host, because it has already entered the
requested Test Mode.

In order to fix the error, we move the actual
start of Test Mode right after we receive
Transfer Complete event of the status phase.
Signed-off-by: NGerard Cauvy <g-cauvy1@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we set Run/Stop bit, we also move the
core to Rx.Detect state so that USB3 handshake
can start from a known location.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We need to dynamically re-size TxFifos for the
cases where default values will not do.

While at that, we create a simple function which,
for now, will just allocate one full packet fifo
space for each of the enabled endpoints.

This can be improved later in order to allow for
better throughput by allocating more space for
endpoints which could make good use of that like
isochronous and bulk.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Only bit 3 of the event status bitfield is valid
and the others should not be considered.

Make sure SW matches documentation on that case
to avoid bogus debugging prints which would
confuse an engineer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ep->max_streams is a mere hint to the gadget
driver that 'ep' supports stream handling. Using
that as a decision variable for enabling streams
was my worst brain-fart to date.

Instead, we should check from the Superspeed
Endpoint Companion Descriptor if the endpoint
has requested streams. For that we need a little
re-factoring but it is now correct.
Debugged-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Instead of special functions and shortcuts for sending our internal
answers to the host we started doing what the gadget does and used the
public API for this. Since we only were using a few fields the
usb_request was enough. Later added the list handling in order to
synchronize the host / gadget events and now we require to have the
dwc3_request struct around our usb_request or else we touch memory that
does not belong to us. So this patch does this.
Reported-by: NPartha Basak <p-basak2@ti.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3 revisions <1.88a have an issue which would
case a missing Disconnect event if cable is
disconnected while there's a Setup packet
pending the FIFO.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

RTL revisions <1.83a have an issue where, depending
on the link partner, the USB link might do multiple
entry/exit of low power states before a transfer
takes place causing degraded throughput.

The suggested workaround is to clear bits
12:9 of DCTL register if we see a transition
from U1|U2 to U0 and only re-enable that on
a transfer complete IRQ and we have no pending
transfers on any of the enabled endpoints.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since the re-worked ep0 handling (which uses HW's hints to recognize the ep0
status) we lost the delayed status handling. This is used by the file and mass
storage gadget to gain some extra time so setup its internal status before it
can proceed further requests.
In particular the storage gadget does nothing on USB_REQ_SET_CONFIGURATION but
wakes up a thread which handles the request. If the udc driver continues ep0
handling before the thread did its work then then endpoint is not yet
configured and further requests will fail. Once the gadget is ready, it will
enqueue an empty packet which is used for synchronization.
In order to fix this issue, the patch does the following:
Set ->delayed_status once the delayed_status has been notices and do not
continue on the next XferNotReady event. We will continues ep0 processing once
the gadget enqueued the zero packet for synchronization.

A cleaner approach would be to enforce the gadget to enqueue an empty
(zero) request even for the status phase but this would do for now.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There are two where need to set operational mode:
- during initialization while we decide to run in host,device or DRD
  mode
- at runtime via the debugfs interface.

This patch provides a new function which sets the operational mode and
moves its initialiation to the mode switch instead in the gadget code
itself.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

hardware will tell us how many event buffers we
need to support, so let's allocate the array
dynamically too.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

if we want to support situations where we have
both SoC and PCIe versions of the IP on the same
platform, we need to have sequential numbers between
them, otherwise we will still have name collisions.

Because of that, we need to move dwc3_get/put_device_id()
to core.c and export that symbol to be used by glue
layers.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The GetStatus (STD)-request is handled the driver and uses a tiny hack
to send the two bytes long answer. This patch removes the custom hack
uses the normal usb_ep_queue() for that.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This makes testing a lot easier when trying to
switch between host and device modes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>