RFC5061 Section 5.2.  Upon Reception of an ASCONF Chunk

V2)  In processing the chunk, the receiver should build a
     response message with the appropriate error TLVs, as
     specified in the Parameter type bits, for any ASCONF
     Parameter it does not understand.  To indicate an
     unrecognized parameter, Cause Type 8 should be used as
     defined in the ERROR in Section 3.3.10.8, [RFC4960].  The
     endpoint may also use the response to carry rejections for
     other reasons, such as resource shortages, etc., using the
     Error Cause TLV and an appropriate error condition.

So we should indicate an unrecognized parameter with error
SCTP_ERROR_UNKNOWN_PARAM in ACSONF-ACK chunk, not
SCTP_ERROR_INV_PARAM.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

RFC5061 had changed the error cause codes for Dynamic Address
Reconfiguration As the following:

       Cause Code
       Value          Cause Code
       ---------      ----------------
       0x00A0          Request to Delete Last Remaining IP Address
       0x00A1          Operation Refused Due to Resource Shortage
       0x00A2          Request to Delete Source IP Address
       0x00A3          Association Aborted Due to Illegal ASCONF-ACK
       0x00A4          Request Refused - No Authorization

This patch fix the error cause codes.
Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>

Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code makes the UCC whose register range includes the current mdio
register to be the MII managemnt interface master of the QE. If there is more
than one mdio bus for QE, the UCC of the last mdio bus will be the MII
management interface master which will make the primary mdio bus working
unproperly, e.g. can not get the right clock. Normally the primary mdio bus is
the first UEC's mdio bus.
This patch allows the first UCC to be the MII management interface master of the
multiple UCC mdio buses.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable fiber/copper auto selection for Marvell m88e1111 SGMII support.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Can remove anonymous union now it has one field.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define three accessors to get/set dst attached to a skb

struct dst_entry *skb_dst(const struct sk_buff *skb)

void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)

void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;

Delete skb->dst field
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb

Delete skb->rtable field

Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct sk_buff uses one union to define dst and rtable fields.

We want to replace direct access to these pointers by accessors.

First patch adds a new "unsigned long _skb_dst;" opaque field
in this union.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With bi-directional stress traffic, the receiver could hang causing the
hardware to stop and a "Detected Tx Unit Hang" message dumped to the system
logfile.  Temporarily workaround this issue by disabling Tx flow control by
default.  The issue is currently being investigated and a follow-on patch
will be provided to revert this when it is resolved.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provides support for the next generation Intel desktop
and mobile gigabit ethernet LOM adapters.  These adapters are the
follow-on parts to the LOMs tied to the prior ICH chipsets and are
comprised of a MAC in the PCH chipset and an external PHY (82577 for
mobile and 82578 for desktop versions).  New features consist of PHY
wakeup to save power by completely turning off the MAC while in Sx
state, and 4K jumbo frames.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By putting the maximum frame size supported by the hardware into the
adapter structure, the change_mtu entry point function can be cleaned
up of checks for all the different max frame sizes supported by
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The flow control thresholds, i.e. high and low watermarks of the Rx
FIFO for when the hardware should transmit PAUSE frames (XON and XOFF,
respectively), need to be tuned for more efficient use of the FIFO.
The logic to set the thresholds for parts that support early-receive
(ERT) was also wrong in that it should check whether jumbo frames are
in use.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During reset, the driver was attempting to disable the Smart Powerdown
feature even if the part does not support Smart Powerdown.  Check for
support before attempting to disable the feature.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CRC stripping should be enabled by default but was not if it was not
specified as a module parameter.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/forcedeth.c

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default the driver opens 8 TX queues (defined by MLX4_EN_NUM_TX_RINGS).
If the driver is configured to support Per Priority Flow Control, we open
8 additional TX rings.
dev->real_num_tx_queues is always set to be MLX4_EN_NUM_TX_RINGS.
The mlx4_en_select_queue() function uses standard hashing (skb_tx_hash)
in case that PPFC is not supported or the skb contain a vlan tag,
otherwise the queue is selected according to vlan priority.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt moderation should not depend on number of incoming
bytes, but on number of incoming packets.
The previous scheme caused very high interrupts rate for small
messages when big MTU was configured.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the initialization of one of the ports failed,
there is no need to fail the other one as well.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

en_params.c file now only handles Ethtool functionality
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For each debug message, the message will show interface name in case
that the net device was registered, and PCI bus ID with port number
if we were not registered yet. Messages that are not port/netdev specific
stayed in the old format
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup

This patch fixes a bug which unconfigured struct tcf_proto keeps
chaining in tc_ctl_tfilter(), and avoids kernel panic in
cls_cgroup_classify() when we use cls_cgroup.

When we execute 'tc filter add', tcf_proto is allocated, initialized
by classifier's init(), and chained.  After it's chained,
tc_ctl_tfilter() calls classifier's change().  When classifier's
change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto.

In addition, cls_cgroup is initialized in change() not in init().  It
accesses unconfigured struct tcf_proto which is chained before
change(), then hits Oops.
Signed-off-by: NMinoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca>
Tested-by: NMinoru Usui <usui@mxm.nes.nec.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	Patch to fix bad length checking in e1000.  E1000 by default does two
things:

1) Spans rx descriptors for packets that don't fit into 1 skb on recieve
2) Strips the crc from a frame by subtracting 4 bytes from the length prior to
doing an skb_put

Since the e1000 driver isn't written to support receiving packets that span
multiple rx buffers, it checks the End of Packet bit of every frame, and
discards it if its not set.  This places us in a situation where, if we have a
spanning packet, the first part is discarded, but the second part is not (since
it is the end of packet, and it passes the EOP bit test).  If the second part of
the frame is small (4 bytes or less), we subtract 4 from it to remove its crc,
underflow the length, and wind up in skb_over_panic, when we try to skb_put a
huge number of bytes into the skb.  This amounts to a remote DOS attack through
careful selection of frame size in relation to interface MTU.  The fix for this
is already in the e1000e driver, as well as the e1000 sourceforge driver, but no
one ever pushed it to e1000.  This is lifted straight from e1000e, and prevents
small frames from causing the underflow described above
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Tested-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After some discussion offline with Christoph Lameter and David Stevens
regarding multicast behaviour in Linux, I'm submitting a slightly
modified patch from the one Christoph submitted earlier.

This patch provides a new socket option IP_MULTICAST_ALL.

In this case, default behaviour is _unchanged_ from the current
Linux standard. The socket option is set by default to provide
original behaviour. Sockets wishing to receive data only from
multicast groups they join explicitly will need to clear this
socket option.
Signed-off-by: NNivedita Singhvi <niv@us.ibm.com>
Signed-off-by: Christoph Lameter<cl@linux.com>
Acked-by: NDavid Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pure cleanups
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Print-out the error value when sock_alloc_send_skb() fails in
the IPv6 neighbor discovery code - can be useful for debugging.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a phy_power_down parameter to forcedeth: set to 1 to power down the
phy and disable the link when an interface goes down; set to 0 to always
leave the phy powered up.

The phy power state persists across reboots; Windows, some BIOSes, and
older versions of Linux don't bother to power up the phy again, forcing
users to remove all power to get the interface working (see
http://bugzilla.kernel.org/show_bug.cgi?id=13072).  Leaving the phy
powered on is the safest default behavior.  Users accustomed to seeing
the link state reflect the interface state and/or wanting to minimize
power consumption can set phy_power_down=1 if compatibility with other
OSes is not an issue.
Signed-off-by: NEd Swierk <eswierk@aristanetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network device TX is never run in IRQ context, and skb is freed outside
of the IRQ-disabling spin lock. So checking for IRQ was a waste of time
here.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the unlikely event that gprs_writeable() and gprs_xmit() check for
writeability at the same, we could stop the device queue forever.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slight refactoring of duplicated wait for idle checks
Spelling fix
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: jie.yang@atheros.com
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several EISA device IDs for 3c509 family network cards are missing from 
the driver, making the cards unusable in their EISA mode.  Here's a fix to 
add them based on the EISA configuration files distributed by 3Com and our 
eisa.ids database.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add 'autoconf' and 'disable_ipv6' parameters to the IPv6 module.

The first controls if IPv6 addresses are autoconfigured from
prefixes received in Router Advertisements.  The IPv6 loopback
(::1) and link-local addresses are still configured.

The second controls if IPv6 addresses are desired at all.  No
IPv6 addresses will be added to any interfaces.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should not be stopping the subqueues in cpmac_end_xmit
but rather test the status of them. Replace the calls to
netif_subqueue_stop by __netif_subqueue_stopped. This
fixes an unrecoverable exception from happening when
running the driver.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>