Always configure an FCoE L2 ring with a mini-jumbo MTU size (2500).
To do that we had to move the rx_buf_size parameter from per
function level to a per ring level.
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Suggested by Alexander Zimmermann
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like metrics, the ICMP rate limiting bits are cached state about
a destination.  So move it into the inet_peer entries.

If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always lookup to see if we have an existing inetpeer entry for
a route.  Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().

Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't allow everybody to set terminator via sysfs.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't allow everybody to write to mb0_id file.
Signed-off-by: NVasiliy Kulikov <segoon@openwall.com>
Acked-by: NKurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fdb_create() puts a new fdb into hash with only addr set. This is
not good, since there are callers, that search the hash w/o the lock
and access all the other its fields.

Applies to current netdev tree.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the RxFIFO interruption is masked for most 8168, nothing prevents
it to appear in the irq status word. This is no excuse to crash.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>

Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).

- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
  Missed ~55% packets. Note:
  - this is an old SiS 965L motherboard
  - the 8168 chipset emits (lots of) control frames towards the sender

- RTL_GIGA_MAC_VER_26
  The chipset does not go into a frenzy of mac control pause when it
  crashes yet but it can still be crashed. It needs more work.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>

I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>

Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Acked-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nlmsg_cancel can accept NULL as its second argument, so for similarity,
this patch extends genlmsg_cancel to be able to accept a NULL second
argument as well.
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 709b46e8 ("net: Add compat
ioctl support for the ipv4 multicast ioctl SIOCGETSGCNT") added the
correct plumbing to handle SIOCGETSGCNT properly.

However, whilst definiting a proper "struct compat_sioc_sg_req" it
isn't actually used in ipmr_compat_ioctl().

Correct this oversight.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Flavio Leitner, there is no synchronization to protect
NIU's get_stats method from seeing a NULL pointer in either
np->rx_rings or np->tx_rings.  In fact, as far as ->ndo_get_stats
is concerned, these values are set completely asynchronously.

Flavio attempted to fix this using a RW semaphore, which in fact
works most of the time.  However, dev_get_stats() can be invoked
from non-sleepable contexts in some cases, so this fix doesn't
work in all cases.

So instead, control the visibility of the np->{rx,tx}_ring pointers
when the device is being brough up, and use properties of the device
down sequence to our advantage.

In niu_get_stats(), return immediately if netif_running() is false.
The device shutdown sequence first marks the device as not running (by
clearing the __LINK_STATE_START bit), then it performans a
synchronize_rcu() (in dev_deactive_many()), and then finally it
invokes the driver ->ndo_stop() method.

This guarentees that all invocations of niu_get_stats() either see
netif_running() as false, or they see the channel pointers before
->ndo_stop() clears them out.

If netif_running() is true, protect against startup races by loading
the np->{rx,tx}_rings pointer into a local variable, and punting if
it is NULL.  Use ACCESS_ONCE to prevent the compiler from reloading
the pointer on us.

Also, during open, control the order in which the pointers and the
ring counts become visible globally using SMP write memory barriers.
We make sure the np->num_{rx,tx}_rings value is stable and visible
before np->{rx,tx}_rings is.

Such visibility control is not necessary on the niu_free_channels()
side because of the RCU sequencing that happens during device down as
described above.  We are always guarenteed that all niu_get_stats
calls are finished, or will see netif_running() false, by the time
->ndo_stop is invoked.
Reported-by: NFlavio Leitner <fleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CHOKe ("CHOose and Kill" or "CHOose and Keep") is an alternative
packet scheduler based on the Random Exponential Drop (RED) algorithm.

The core idea is:
  For every packet arrival:
  	Calculate Qave
	if (Qave < minth)
	     Queue the new packet
	else
	     Select randomly a packet from the queue
	     if (both packets from same flow)
	     then Drop both the packets
	     else if (Qave > maxth)
	          Drop packet
	     else
	       	  Admit packet with proability p (same as RED)

See also:
  Rong Pan, Balaji Prabhakar, Konstantinos Psounis, "CHOKe: a stateless active
   queue management scheme for approximating fair bandwidth allocation",
  Proceeding of INFOCOM'2000, March 2000.

Help from:
     Eric Dumazet <eric.dumazet@gmail.com>
     Patrick McHardy <kaber@trash.net>
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The change to allow divisor to be a parameter (in 2.6.38-rc1)
 commit 817fb15d
introduced a possible deadlock caught by sparse.

The scheduler tree lock was left locked in the case of an incorrect
divisor value. Simplest fix is to move test outside of lock
which also solves problem of partial update.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we end up including include/linux/node.h (either explicitly
or implicitly) that header has a definition of "structt node"
too.

So rename the one we use in fib_trie to "rt_trie_node" to avoid
the conflict.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNandita Dukkipati <nanditad@google.com>

Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There was some confusion at LCA as to why the sysctl tcp_ecn took one
of three values when it was documented as a Boolean.  This patch fixes
the documentation.
Signed-off-by: NPeter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new 'devgroup' match to match on the device group of the
incoming and outgoing network device of a packet.
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Commit 8f574b35 ("atl1c: Add AR8151 v2
support and change L0s/L1 routine") added support for a new adapter
but failed to add it to the PCI device table.
Signed-Off-By: NChuck Ebbert <cebbert@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This error was reported by cppcheck:
drivers/s390/net/smsgiucv.c:63: error: Using sizeof for array given as
function argument returns the size of pointer.

Although there is no runtime problem as long as sizeof(u8 *) == 8,
this misleading code should get fixed.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This error was reported by cppcheck:
drivers/s390/net/netiucv.c:568: error: Using sizeof for array given
as function argument returns the size of pointer.

sizeof(ipuser) did not result in 16 (as many programmers would have
expected) but sizeof(u8 *), so it is 4 or 8, too small here.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For OSA the CHPARM-definition determines the number of available
outbound queues.
A CHPARM-change may occur while a Linux system with probed
OSA device is in suspend state. This patch enables proper
resuming of an OSA device in this case.
Signed-off-by: NUrsula braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For HiperSockets the framesize-definition determines the selected
mtu-size and the size of the allocated qdio buffers.
A framesize-change may occur while a Linux system with probed
HiperSockets device is in suspend state. This patch enables proper
resuming of a HiperSockets device in this case.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HiperSockets and OSA hardware report a maximum MTU size. Add checking
to reject larger MTUs than allowed by hardware.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting of a MAC-address may fail because an already used MAC-address
is to bet set or because of authorization problems. In those cases
qeth issues a message, but the mentioned MAC-address is not the
new MAC-address to be set, but the actual MAC-address. This patch
chooses now the new MAC-address to be set for the error messages.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a message carries multiple commands and one of them triggers
an error, we have to report to the userspace which one was that.
The line number of the command plays this role and there's an attribute
reserved in the header part of the message to be filled out with the error
line number. In order not to modify the original message received from
the userspace, we construct a new, complete netlink error message and
modifies the attribute there, then send it.
Netlink is notified not to send its ACK/error message.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Like Herbert's change from a few days ago:

66c46d74 gro: Reset dev pointer on reuse

this may not be necessary at this point, but we should still clean up
the skb->skb_iif.  If not we may end up with an invalid valid for
skb->skb_iif when the skb is reused and the check is done in
__netif_receive_skb.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a dummy ip_set_get_ip6_port function that unconditionally
returns false for CONFIG_IPV6=n and convert the real function
to ipv6_skip_exthdr() to avoid pulling in the ip6_tables module
when loading ipset.
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Don't fall through in the switch statement, otherwise IPv4 headers
are incorrectly parsed again as IPv6 and the return value will always
be 'false'.
Signed-off-by: NPatrick McHardy <kaber@trash.net>