There are multiple ways in which a PORT_BRIDGE_FLAGS attribute can be
expressed by the bridge through switchdev, and not all of them can be
emulated by DSA mid-layer API at the same time.

One possible configuration is when the bridge offloads the port flags
using a mask that has a single bit set - therefore only one feature
should change. However, DSA currently groups together unicast and
multicast flooding in the .port_egress_floods method, which limits our
options when we try to add support for turning off broadcast flooding:
do we extend .port_egress_floods with a third parameter which b53 and
mv88e6xxx will ignore? But that means that the DSA layer, which
currently implements the PRE_BRIDGE_FLAGS attribute all by itself, will
see that .port_egress_floods is implemented, and will report that all 3
types of flooding are supported - not necessarily true.

Another configuration is when the user specifies more than one flag at
the same time, in the same netlink message. If we were to create one
individual function per offloadable bridge port flag, we would limit the
expressiveness of the switch driver of refusing certain combinations of
flag values. For example, a switch may not have an explicit knob for
flooding of unknown multicast, just for flooding in general. In that
case, the only correct thing to do is to allow changes to BR_FLOOD and
BR_MCAST_FLOOD in tandem, and never allow mismatched values. But having
a separate .port_set_unicast_flood and .port_set_multicast_flood would
not allow the driver to possibly reject that.

Also, DSA doesn't consider it necessary to inform the driver that a
SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute was offloaded, because it
just calls .port_egress_floods for the CPU port. When we'll add support
for the plain SWITCHDEV_ATTR_ID_PORT_MROUTER, that will become a real
problem because the flood settings will need to be held statefully in
the DSA middle layer, otherwise changing the mrouter port attribute will
impact the flooding attribute. And that's _assuming_ that the underlying
hardware doesn't have anything else to do when a multicast router
attaches to a port than flood unknown traffic to it.  If it does, there
will need to be a dedicated .port_set_mrouter anyway.

So we need to let the DSA drivers see the exact form that the bridge
passes this switchdev attribute in, otherwise we are standing in the
way. Therefore we also need to use this form of language when
communicating to the driver that it needs to configure its initial
(before bridge join) and final (after bridge leave) port flags.

The b53 and mv88e6xxx drivers are converted to the passthrough API and
their implementation of .port_egress_floods is split into two: a
function that configures unicast flooding and another for multicast.
The mv88e6xxx implementation is quite hairy, and it turns out that
the implementations of unknown unicast flooding are actually the same
for 6185 and for 6352:

behind the confusing names actually lie two individual bits:
NO_UNKNOWN_MC -> FLOOD_UC = 0x4 = BIT(2)
NO_UNKNOWN_UC -> FLOOD_MC = 0x8 = BIT(3)

so there was no reason to entangle them in the first place.

Whereas the 6185 writes to MV88E6185_PORT_CTL0_FORWARD_UNKNOWN of
PORT_CTL0, which has the exact same bit index. I have left the
implementations separate though, for the only reason that the names are
different enough to confuse me, since I am not able to double-check with
a user manual. The multicast flooding setting for 6185 is in a different
register than for 6352 though.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.

This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes: 93efb0c6 ("octeontx2-pf: Fix out-of-bounds read in otx2_get_fecparam()")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a simple helper function that indicates whether a channel has
been initialized.  This abstacts/hides the details of how this is
determined.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a new function to abstract the knowledge of whether hashed
routing and filter tables are supported for a given IPA instance.

IPA v4.2 is the only one that doesn't support hashed tables (now
and for the foreseeable future), but the name of the helper function
is better for explaining what's going on.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ipa_cmd_register_write_valid() we verify that values we will
supply to a REGISTER_WRITE IPA immediate command will fit in
the fields that need to hold them.  This patch fixes some issues
in that function and ipa_cmd_register_write_offset_valid().

The dev_err() call in ipa_cmd_register_write_offset_valid() has
some printf format errors:
  - The name of the register (corresponding to the string format
    specifier) was not supplied.
  - The IPA base offset and offset need to be supplied separately to
    match the other format specifiers.
Also make the ~0 constant used there to compute the maximum
supported offset value explicitly unsigned.

There are two other issues in ipa_cmd_register_write_valid():
  - There's no need to check the hash flush register for platforms
    (like IPA v4.2) that do not support hashed tables
  - The highest possible endpoint number, whose status register
    offset is computed, is COUNT - 1, not COUNT.

Fix these problems, and add some additional commentary.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing the IPA core clock and interconnects, it's
possible we'll get an EPROBE_DEFER error.  This isn't really an
error, it's just means we need to be re-probed later.

Use dev_err_probe() to report the error rather than dev_err().
This avoids polluting the log with these "error" messages.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch actually fixes a bug, though it doesn't affect the two
platforms supported currently.  The fix implements GSI memory
pointers a bit differently.

For IPA version 4.5 and above, the address space for almost all GSI
registers is adjusted downward by a fixed amount.  This is currently
handled by adjusting the I/O virtual address pointer after it has
been mapped.  The bug is that the pointer is not "de-adjusted" as it
should be when it's unmapped.

This patch fixes that error, but it does so by maintaining one "raw"
pointer for the mapped memory range.  This is assigned when the
memory is mapped and used to unmap the memory.  This pointer is also
used to access the two registers that do *not* sit in the "adjusted"
memory space.

Rather than adjusting *that* pointer, we maintain a separate pointer
that's an adjusted copy of the "raw" pointer, and that is used for
most GSI register accesses.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code at line 967 implies that rsp->fwdata.supported_fec may be up to 4:

 967: if (rsp->fwdata.supported_fec <= FEC_MAX_INDEX)

If rsp->fwdata.supported_fec evaluates to 4, then there is an
out-of-bounds read at line 971 because fec is an array with
a maximum of 4 elements:

 954         const int fec[] = {
 955                 ETHTOOL_FEC_OFF,
 956                 ETHTOOL_FEC_BASER,
 957                 ETHTOOL_FEC_RS,
 958                 ETHTOOL_FEC_BASER | ETHTOOL_FEC_RS};
 959 #define FEC_MAX_INDEX 4

 971: fecparam->fec = fec[rsp->fwdata.supported_fec];

Fix this by properly indexing fec[] with rsp->fwdata.supported_fec - 1.
In this case the proper indexes 0 to 3 are used when
rsp->fwdata.supported_fec evaluates to a range of 1 to 4, correspondingly.

Fixes: d0cf9503 ("octeontx2-pf: ethtool fec mode support")
Addresses-Coverity-ID: 1501722 ("Out-of-bounds read")
Signed-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a spelling mistake in the text in array rpm_rx_stats_fields,
fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_rm_vport_all_mac_table() is bloated, so split it into
separate functions for readability and maintainability.
Signed-off-by: NHao Chen <chenhao288@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make it more readable and maintainable, split
hclgevf_set_rss_tuple() into two parts.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make it more readable and maintainable, split
hclge_set_rss_tuple() into two parts.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclgevf_cmd_send() is bloated, so split it into separate
functions for readability and maintainability.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_cmd_send() is bloated, so split it into separate
functions for readability and maintainability.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_dbg_dump_qos_buf_cfg() is bloated, so split it into
separate functions for readability and maintainability.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To improve code readability and maintainability, separate
the flow type parsing part and the converting part from
bloated hclgevf_get_rss_tuple().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To improve code readability and maintainability, separate
the flow type parsing part and the converting part from
bloated hclge_get_rss_tuple().
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To improve code readability and maintainability, separate
the command handling part and the status parsing part from
bloated hclge_set_vf_vlan_common().
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use common ipv6_addr_any() to determine if an addr is ipv6 any addr.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As more commands are added, hns3_dbg_cmd_write() is going to
get more bloated, so move the part about command check into
a separate function.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To improve code readability and maintainability, refactor
hclgevf_cmd_convert_err_code() with an array of imp_errcode
and common_errno mapping, instead of a bloated switch/case.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To improve code readability and maintainability, refactor
hclge_cmd_convert_err_code() with an array of imp_errcode
and common_errno mapping, instead of a bloated switch/case.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update RTL8822C devices' RF_A tables to v60.
The new parameters fix incorrect RSSI report under 2.4G link.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-9-pkshih@realtek.com

Update RTL8822C devices' RF_B tables to v60.
The new parameters fix incorrect RSSI report under 2.4G link.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-8-pkshih@realtek.com

Update RTL8822C devices' RF_A tables to v60.
The new parameters fix incorrect RSSI report under 2.4G link.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-7-pkshih@realtek.com

Update RTL8822C devices' MAC/BB tables to v60.
The new parameters fix incorrect RSSI report under 2.4G link.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-6-pkshih@realtek.com

Replace tasklet so we can do tx scheduling in parallel. Since throughput
is delay-sensitive in most cases, we allocate a dedicated, high priority
wq for our needs.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-5-pkshih@realtek.com

Use napi to reduce overhead on rx interrupts.

Driver used to interrupt kernel for every Rx packet, this could
affect both system and network performance. NAPI is a mechanism that
uses polling when processing huge amount of traffic, by doing this
the number of interrupts can be decreased.

Network performance can also benefit from this patch. Since TCP
connection is bidirectional and acks are required for every several
packets. These ack packets occupie the PCI bus bandwidth and could
lead to performance degradation.

When napi is used, GRO receive is enabled by default in the mac80211
stack. So mac80211 won't pass every RX TCP packets to the kernel TCP
network stack immediately. Instead an aggregated large length TCP packet
will be delivered.

This reduces the tx acks sent and gains rx performance. After the patch,
the Rx throughput increases about 25Mbps in 11ac.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Tested-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-4-pkshih@realtek.com

Since we set the IEEE80211_HW_HAS_RATE_CONTROL flag, so use_rts in
ieee80211_tx_info will never be set in the ieee80211_xmit_fast path.
Add length check for skb to decide whether rts is needed.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-3-pkshih@realtek.com

Register rrsr determines the response rate we send.
In field tests, using rate higher than current tx rate could lead
to difficulty for the receiving end to receive management/control
frames. Calculate current modulation level by tx rate then cross out
rate higher than those.
Signed-off-by: NPo-Hao Huang <phhuang@realtek.com>
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Reviewed-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-2-pkshih@realtek.com

We use this driver as a backport that also runs on older kernels (as
part of the backports project).  So we use some checks to backport or
prevent code from compiling in incompatible kernel version.

When I took one of the PNVM patches from the backport, I accidentally
left the comment that a certain part of the code doesn't work in older
kernels.  This obviously should never be valid for the mainline.
Remove this comment.
Reported-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20210211223049.40d545a0fa89.I04793aaa5312b926335c8db32131f000432df511@changeid

No real dependency on XPS, but on RX queue mapping, which
is being selected by TLS_DEVICE.
Signed-off-by: NTariq Toukan <tariqt@nvidia.com>
Reviewed-by: NMaxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cleaning up tx descriptors first increases the chance that
rtl_rx() can allocate new skb's from the cache.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_ifsioc_locked() is called with only RCU read lock, so when
there is a parallel writer changing the mac address, it could
get a partially updated mac address, as shown below:

Thread 1			Thread 2
// eth_commit_mac_addr_change()
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
				// dev_ifsioc_locked()
				memcpy(ifr->ifr_hwaddr.sa_data,
					dev->dev_addr,...);

Close this race condition by guarding them with a RW semaphore,
like netdev_get_name(). We can not use seqlock here as it does not
allow blocking. The writers already take RTNL anyway, so this does
not affect the slow path. To avoid bothering existing
dev_set_mac_address() callers in drivers, introduce a new wrapper
just for user-facing callers on ioctl and rtnetlink paths.

Note, bonding also changes slave mac addresses but that requires
a separate patch due to the complexity of bonding code.

Fixes: 3710becf ("net: RCU locking for simple ioctl()")
Reported-by: N"Gong, Sishuai" <sishuai@purdue.edu>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: NCong Wang <cong.wang@bytedance.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.

Fixes: e531f767 ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NStefan Chulski <stefanc@marvell.com>
Reviewed-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

J721e, J7200 and AM64 have multi port switches which can work in multi
mac mode and in switch mode. Add support for configuring this HW in
switch mode using devlink and switchdev notifiers.

Support is similar to existing CPSW switchdev implementation of TI's 32 bit
platform like AM33/AM43/AM57.

To enable switch mode:
devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime

All configuration is implemented via switchdev API and notifiers.
Supported:
      - SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
      - SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
      - SWITCHDEV_ATTR_ID_PORT_STP_STATE
      - SWITCHDEV_OBJ_ID_PORT_VLAN
      - SWITCHDEV_OBJ_ID_PORT_MDB
      - SWITCHDEV_OBJ_ID_HOST_MDB

Hence AM65 CPSW switchdev driver supports:
     - FDB offloading
     - MDB offloading
     - VLAN filtering and offloading
     - STP
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register netdevice notifiers in order to receive notification when
individual MAC ports are added to the HW bridge.
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

AM65 NUSS ethernet switch on K3 devices can be configured to work either
in independent mac mode where each port acts as independent network
interface (multi mac) or switch mode.

Add devlink hooks to provide a way to switch b/w these modes.

Rationale to use devlink instead of defaulting to bridge mode is that
SoC use cases require to support multiple independent MAC ports with no
switching so that users can use software bridges with multi-mac
configuration (e.g: to support LAG, HSR/PRP, etc). Also, switching
between multi mac and switch mode requires significant Port and ALE
reconfiguration, therefore is easier to be made as part of mode change
devlink hooks. It also allows to keep user interface similar to what
was implemented for the previous generation of TI CPSW IP
(on AM33/AM43/AM57 SoCs).
Signed-off-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>