i2c_probe was quite complex and slow, so I rewrote it in a more
efficient and hopefully clearer way.

Note that this slightly changes the way the module parameters are
handled. This shouldn't change anything for the most common cases
though.

For one thing, the function now respects the order of the parameters
for address probing. It used to always do lower addresses first. The
new approach gives the user more control.

For another, ignore addresses don't overrule probe addresses anymore.
This could have been restored the way it was at the cost of a few more
lines of code, but I don't think it's worth it. Both lists are given
as module parameters, so a user would be quite silly to specify the
same addresses in both lists. The normal addresses list is the only
one that isn't controlled by a module parameter, thus is the only one
the user may reasonably want to remove an address from.

Another significant change is the fact that i2c_probe() will no more
stop when a detection function returns -ENODEV. Just because a driver
found a chip it doesn't support isn't a valid reason to stop all
probings for this one driver. This closes the long standing lm_sensors
ticket #1807.

  http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1807

I updated the documentation accordingly.

In terms of algorithmic complexity, the new code is way better. If
I is the ignore address count, P the probe address count, N the
normal address count and F the force address count, the old code
was doing 128 * (F + I + P + N) iterations max, while the new code
does F + P + ((I+1) * N) iterations max. For the most common case
where F, I and P are empty, this is down from 128 * N to N.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch updates the VID entries, so any future
Intel CPU will be detected as unknown rather than 9.0
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the common vid_from_reg function in lm78 rather than
reimplementing it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I see very little reason why vid_from_reg is inlined. It is not
exactly short, its parameters are seldom known in advance, and it is
never called in speed critical areas. Uninlining it should cause
little performance loss if any, and saves a signficant space as well
as compilation time.

As suggested by Alexey Dobriyan, I am leaving vid_to_reg inline for now,
as it is short and has a single user so far.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Delete DEFAULT_VRM from hwmon-vid.h, it has no more users.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleanup hwmon-vid a bit, fixing typos, rewording some comments and
reindenting properly at places.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.

Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: NJean Delvare <khali@linux-fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The i2c_detect function has no more user, delete it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We now have two identical structures, i2c_address_data in i2c-sensor.h
and i2c_client_address_data in i2c.h. We can kill one of them, I choose
to keep the one in i2c.h as it makes more sense (this structure is not
specific to sensors.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The way i2c-sensor handles forced addresses could be optimized. It
defines a structure (i2c_force_data) to associate a module parameter
with a given kind value, but in fact this kind value is always the
index of the structure in each array it is used in. So this additional
value can be omitted, and still be deduced in the code handling these
arrays.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add support for kind-forced addresses to i2c_probe, like i2c_detect
has for (essentially) hardware monitoring drivers.

Note that this change will slightly increase the size of the drivers
using I2C_CLIENT_INSMOD, with no immediate benefit. This is a
requirement if we want to merge i2c_probe and i2c_detect though, and
seems a reasonable price to pay in comparison with the previous
cleanups which saved much more than that (such as the i2c-isa cleanup
or the i2c address ranges removal.)
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove an unused macro and an outdated comment from the lm85 driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move SENSORS_LIMIT from i2c-sensor.h to hwmon.h, as it is in no way
related to i2c.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The debugging messages in i2c-core are more confusing than helpful. Some
lack their trailing newline, some lack a prefix, some are redundant,
some lack precious information. Here is my attempt to introduce some
standardization in there.

I also changed two messages in i2c-dev to make it clear they come from
i2c-dev.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a typo in the i2c documentation: the i2c bus scanning tool found in
lm_sensors is called i2cdetect, not i2c_detect.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I've been running with this patch for a while now, and while I've never
seen it trigger except with buggy hardware I think it is a cleaner way
to handle a busy bus. I had -EBUSY until about 10 minutes ago but -EIO
seems to be what most of the existing algo drivers will return in the
same circumstances.
Signed-off-by: NIan Campbell <icampbell@arcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We could inline i2c_adapter_id, as it is really, really short. Doing
so saves a few bytes both in i2c-core and in the drivers using this
function.

                                            before     after      diff
drivers/hwmon/adm1026.ko                     41344     41305       -39
drivers/hwmon/asb100.ko                      27325     27246       -79
drivers/hwmon/gl518sm.ko                     20824     20785       -39
drivers/hwmon/it87.ko                        26419     26380       -39
drivers/hwmon/lm78.ko                        21424     21385       -39
drivers/hwmon/lm85.ko                        41034     40939       -95
drivers/hwmon/w83781d.ko                     39561     39514       -47
drivers/hwmon/w83792d.ko                     32979     32932       -47
drivers/i2c/i2c-core.ko                      24708     24531      -177
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Super-I/O find functions in hardware monitoring drivers can be tagged
__init as they are only called from functions themselves tagged __init.
Two of them (smsc47b397 and w83627ehf) already do, but the other four
of them (it87, pc87360, smsc47m1 and w83627hf) did not.

This saves a few bytes of memory after the drivers are loaded, 192 in
the case of the it87 driver.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.

Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds documentation entry for W83792D chip.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds registration of hwmon class. Tested with help of i2c-stub.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I would like to announce support for W83792D chip. This driver was developed
by Winbond Electronics Corp. I added sysfs attributes callbacks infrastructure
plus various code fixes and codingstyle cleanups. I would like to thank Winbond
for supporting free software.

This patch is against 2.6.13rc3 plus hwmon-class and hwmon-split.
Separate patch for documantation and hwmon class register will follow.
Signed-off-by: NRudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: NChunhao Huang <DZShen@Winbond.com.tw>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move the definitions of i2c_is_isa_client and i2c_is_isa_adapter from
i2c.h to i2c-isa.h. Only hybrid drivers still need them.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kill all uses of i2c_is_isa_adapter except for the hybrid drivers (it87,
lm78, w83781d). The i2c-isa adapter not being registered with the i2c
core anymore, drivers don't have to fear being erroneously attached to
it.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kill normal_isa in header files, documentation and all chip drivers, as
it is no more used.

normal_i2c could be renamed to normal, but I decided not to do so at the
moment, so as to limit the number of changes. This might be done later
as part of the i2c_probe/i2c_detect merge.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kill all isa-related stuff from i2c_detect, it's not used anymore.

This is one major step in the directiom of merging i2c_probe and
i2c_detect. The last obstacle I can think of is the different way forced
addresses work between sensors and non-sensors i2c drivers. I'll deal
with that in a later patchset.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Call the ISA chip drivers detection function directly instead of relying
on i2c_detect. The net effect is that address lists won't be handled
anymore, but they were mostly useless in the ISA case anyway (pc87360,
smsc47m1, smsc47b397 had already dropped them).

We don't need to handle multiple devices, all we may need is a way to
force a given address instead of the original one (some drivers already
do: sis5595, via686a, w83627hf), and, for drivers supporting multiple
chips, a way to force one given kind. All this may be added later on
demand, but I actually don't think there will be much demand.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All ISA hardware monitoring drivers (including hybrid drivers) now have
a hard dependency on i2c-isa, so they must select I2C_ISA. As a result,
CONFIG_I2C_ISA doesn't need to be left visible to the user. The good
thing here is that users will stop complaining that some driver doesn't
work just because they forgot to compile or load i2c-isa.

At this point, all drivers are working again and the cleanup phase can
begin.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Convert the 10 ISA hardware monitoring drivers (it87, lm78, pc87360,
sis5595, smsc47b397, smsc47m1, via686a, w83627hf, w83627ehf, w83781d) to
explicitely register with i2c-isa. For hybrid drivers (it87, lm78,
w83781d), we now have two separate instances of i2c_driver, one for the
I2C interface of the chip, and one for ISA interface. In the long run,
the one for ISA will be replaced with a different driver type.

At this point, all drivers are working again, except for missing
dependencies in Kconfig.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Convert i2c-isa from a dumb i2c_adapter into a pseudo i2c-core for ISA
hardware monitoring drivers. The isa i2c_adapter is no more registered
with i2c-core, drivers have to explicitely connect to it using the new
i2c_isa_{add,del}_driver interface.

At this point, all ISA chip drivers are useless, because they still
register with i2c-core in the hope i2c-isa is registered there as well,
but it isn't anymore.

The fake bus will be named i2c-9191 in sysfs. This is the number it
already had internally in various places, so it's not exactly new,
except that now the number is seen in userspace as well. This shouldn't
be a problem until someone really has 9192 I2C busses in a given system
;)

The fake bus will no more show in "i2cdetect -l", as it won't be seen by
i2c-dev anymore (not being registered with i2c-core), which is a good
thing, as i2cdetect/i2cdump/i2cset cannot operate on this fake bus
anyway.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Temporarily export a few structures and functions from i2c-core, because we
will soon need them in i2c-isa.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch modifies sensors chip drivers to make use of the new
sysfs class "hwmon".
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds the sysfs class "hwmon" for use by hardware monitoring
(sensors) chip drivers.  It also fixes up the related Kconfig/Makefile
bits.
Signed-off-by: NMark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Document the fact that the W83627EHG is compatible with the W83627EHF.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Drop the separate client name for the LM78-J chip. This is really
only a later revision of the LM78, with almost no difference and
no difference the driver handles in any case.

This was the only client name that had a dash in it, and special care
had to be taken in libsensors because of it. As we plan to write a new
library soon, I'd like to get rid of this exception before we do.

As a nice side effect, it saves 876 bytes in lm78.ko.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The LM75 initialization is a bit agressive, it arbitrarily reconfigures
the chip. Make it only change the bit it needs. This is a port from
the 2.4 kernel version of the driver (lm_sensors).
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove an unused local variable and change the subclient name.
Signed-off-by: NBen Gardner <bgardner@wabtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a spelling error and change a sysfs name.
Signed-off-by: NBen Gardner <bgardner@wabtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>