The current 'bnxt_shutdown' implementation only invokes
'bnxt_ulp_shutdown' to shut down RoCE in the case when the system is in
the path of power off (SYSTEM_POWER_OFF). While this may work in most
cases, it does not work in the smart NIC case, when Linux 'reboot'
command is initiated from the Linux that runs on the ARM cores of the
NIC card. In this particular case, Linux 'reboot' results in a system
'L3' level reset where the entire ARM and associated subsystems are
being reset, but at the same time, Nitro core is being kept in sane state
(to allow external PCIe connected servers to continue to work). Without
properly shutting down RoCE and freeing all associated resources, it
results in the ARM core to hang immediately after the 'reboot'

By always invoking 'bnxt_ulp_shutdown' in 'bnxt_shutdown', it fixes the
above issue

Fixes: 0efd2fc6 ("bnxt_en: Add a callback to inform RDMA driver during PCI shutdown.")
Signed-off-by: NRay Jui <ray.jui@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Russell King says:

====================
SFP/phylink fixes

Here are four phylink fixes:
- the "options" is a big-endian value, we must test the bits taking the
  endian-ness into account.
- improve the handling of RX_LOS polarity, taking no RX_LOS polarity
  bits set to mean there is no RX_LOS functionality provided.
- do not report modules that require the address mode switching as
  supporting SFF8472.
- ensure that the mac_link_down() function is called when phylink_stop()
  is called.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensure that we tell the MAC to take the link down when phylink_stop()
is called, and that this completes prior to phylink_stop() returns.
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We do not support SFP modules which require the address change sequence
as detailed by SFF 8472 revision 1.22 section 8.9.  Warn when these
modules are inserted, and treat them as SFF8079 modules for ethtool.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two bits in the option word for the RX_LOS signal.  One
reports that the RX_LOS signal is active high, the other reports that
it is active low.  When both or neither are set, the result is not
well defined in the specification.

Rather than assuming that neither set means normal RX_LOS, take this
as meaning no RX_LOS signal available, thereby ignoring the signal.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The options word is a be16 quantity, so we need to test the flags
having converted the endian-ness.  Convert the flag bits to be16,
which can be optimised by the compiler, rather than converting a
variable at runtime.
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix obvious typo that first return value is set but not checked.
Signed-off-by: NMax Uvarov <muvarov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the second tipc_rcv() call in tipc_udp_recv(). We have just
checked that the bearer is not up, and calling tipc_rcv() with a bearer
that is not up leads to a TIPC div-by-zero crash in
tipc_node_calculate_timer(). The crash is rare in practice, but can
happen like this:

  We're enabling a bearer, but it's not yet up and fully initialized.
  At the same time we receive a discovery packet, and in tipc_udp_recv()
  we end up calling tipc_rcv() with the not-yet-initialized bearer,
  causing later the div-by-zero crash in tipc_node_calculate_timer().

Jon Maloy explains the impact of removing the second tipc_rcv() call:
  "link setup in the worst case will be delayed until the next arriving
   discovery messages, 1 sec later, and this is an acceptable delay."

As the tipc_rcv() call is removed, just leave the function via the
rcu_out label, so that we will kfree_skb().

[   12.590450] Own node address <1.1.1>, network identity 1
[   12.668088] divide error: 0000 [#1] SMP
[   12.676952] CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.14.2-dirty #1
[   12.679225] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-2.fc27 04/01/2014
[   12.682095] task: ffff8c2a761edb80 task.stack: ffffa41cc0cac000
[   12.684087] RIP: 0010:tipc_node_calculate_timer.isra.12+0x45/0x60 [tipc]
[   12.686486] RSP: 0018:ffff8c2a7fc838a0 EFLAGS: 00010246
[   12.688451] RAX: 0000000000000000 RBX: ffff8c2a5b382600 RCX: 0000000000000000
[   12.691197] RDX: 0000000000000000 RSI: ffff8c2a5b382600 RDI: ffff8c2a5b382600
[   12.693945] RBP: ffff8c2a7fc838b0 R08: 0000000000000001 R09: 0000000000000001
[   12.696632] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8c2a5d8949d8
[   12.699491] R13: ffffffff95ede400 R14: 0000000000000000 R15: ffff8c2a5d894800
[   12.702338] FS:  0000000000000000(0000) GS:ffff8c2a7fc80000(0000) knlGS:0000000000000000
[   12.705099] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   12.706776] CR2: 0000000001bb9440 CR3: 00000000bd009001 CR4: 00000000003606e0
[   12.708847] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   12.711016] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[   12.712627] Call Trace:
[   12.713390]  <IRQ>
[   12.714011]  tipc_node_check_dest+0x2e8/0x350 [tipc]
[   12.715286]  tipc_disc_rcv+0x14d/0x1d0 [tipc]
[   12.716370]  tipc_rcv+0x8b0/0xd40 [tipc]
[   12.717396]  ? minmax_running_min+0x2f/0x60
[   12.718248]  ? dst_alloc+0x4c/0xa0
[   12.718964]  ? tcp_ack+0xaf1/0x10b0
[   12.719658]  ? tipc_udp_is_known_peer+0xa0/0xa0 [tipc]
[   12.720634]  tipc_udp_recv+0x71/0x1d0 [tipc]
[   12.721459]  ? dst_alloc+0x4c/0xa0
[   12.722130]  udp_queue_rcv_skb+0x264/0x490
[   12.722924]  __udp4_lib_rcv+0x21e/0x990
[   12.723670]  ? ip_route_input_rcu+0x2dd/0xbf0
[   12.724442]  ? tcp_v4_rcv+0x958/0xa40
[   12.725039]  udp_rcv+0x1a/0x20
[   12.725587]  ip_local_deliver_finish+0x97/0x1d0
[   12.726323]  ip_local_deliver+0xaf/0xc0
[   12.726959]  ? ip_route_input_noref+0x19/0x20
[   12.727689]  ip_rcv_finish+0xdd/0x3b0
[   12.728307]  ip_rcv+0x2ac/0x360
[   12.728839]  __netif_receive_skb_core+0x6fb/0xa90
[   12.729580]  ? udp4_gro_receive+0x1a7/0x2c0
[   12.730274]  __netif_receive_skb+0x1d/0x60
[   12.730953]  ? __netif_receive_skb+0x1d/0x60
[   12.731637]  netif_receive_skb_internal+0x37/0xd0
[   12.732371]  napi_gro_receive+0xc7/0xf0
[   12.732920]  receive_buf+0x3c3/0xd40
[   12.733441]  virtnet_poll+0xb1/0x250
[   12.733944]  net_rx_action+0x23e/0x370
[   12.734476]  __do_softirq+0xc5/0x2f8
[   12.734922]  irq_exit+0xfa/0x100
[   12.735315]  do_IRQ+0x4f/0xd0
[   12.735680]  common_interrupt+0xa2/0xa2
[   12.736126]  </IRQ>
[   12.736416] RIP: 0010:native_safe_halt+0x6/0x10
[   12.736925] RSP: 0018:ffffa41cc0cafe90 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff4d
[   12.737756] RAX: 0000000000000000 RBX: ffff8c2a761edb80 RCX: 0000000000000000
[   12.738504] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[   12.739258] RBP: ffffa41cc0cafe90 R08: 0000014b5b9795e5 R09: ffffa41cc12c7e88
[   12.740118] R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000002
[   12.740964] R13: ffff8c2a761edb80 R14: 0000000000000000 R15: 0000000000000000
[   12.741831]  default_idle+0x2a/0x100
[   12.742323]  arch_cpu_idle+0xf/0x20
[   12.742796]  default_idle_call+0x28/0x40
[   12.743312]  do_idle+0x179/0x1f0
[   12.743761]  cpu_startup_entry+0x1d/0x20
[   12.744291]  start_secondary+0x112/0x120
[   12.744816]  secondary_startup_64+0xa5/0xa5
[   12.745367] Code: b9 f4 01 00 00 48 89 c2 48 c1 ea 02 48 3d d3 07 00
00 48 0f 47 d1 49 8b 0c 24 48 39 d1 76 07 49 89 14 24 48 89 d1 31 d2 48
89 df <48> f7 f1 89 c6 e8 81 6e ff ff 5b 41 5c 5d c3 66 90 66 2e 0f 1f
[   12.747527] RIP: tipc_node_calculate_timer.isra.12+0x45/0x60 [tipc] RSP: ffff8c2a7fc838a0
[   12.748555] ---[ end trace 1399ab83390650fd ]---
[   12.749296] Kernel panic - not syncing: Fatal exception in interrupt
[   12.750123] Kernel Offset: 0x13200000 from 0xffffffff82000000
(relocation range: 0xffffffff80000000-0xffffffffbfffffff)
[   12.751215] Rebooting in 60 seconds..

Fixes: c9b64d49 ("tipc: add replicast peer discovery")
Signed-off-by: NTommi Rantala <tommi.t.rantala@nokia.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maciej Żenczykowski reported some panics in tcp_twsk_destructor()
that might be caused by the following bug.

timewait timer is pinned to the cpu, because we want to transition
timwewait refcount from 0 to 4 in one go, once everything has been
initialized.

At the time commit ed2e9239 ("tcp/dccp: fix timewait races in timer
handling") was merged, TCP was always running from BH habdler.

After commit 5413d1ba ("net: do not block BH while processing
socket backlog") we definitely can run tcp_time_wait() from process
context.

We need to block BH in the critical section so that the pinned timer
has still its purpose.

This bug is more likely to happen under stress and when very small RTO
are used in datacenter flows.

Fixes: 5413d1ba ("net: do not block BH while processing socket backlog")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NMaciej Żenczykowski <maze@google.com>
Acked-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: a couple of fixes for chunks abandoned in prsctp

Now when abandoning chunks in prsctp, it doesn't consider for frags in
one msg, which would cause peer can never receive the whole frags for
one msg to get them reassembled, these pieces of this msg will stay in
the reasm queue forever and block the following chunks' receiving.

This patchset is to fix them in patch 2 and 3, and also fix another
issue for prsctp in patch 1.
====================
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now for the abandoned chunks in unsent outq, it would just free the chunks.
Because no tsn is assigned to them yet, there's no need to send fwd tsn to
peer, unlike for the abandoned chunks in sent outq.

The problem is when parts of the msg have been sent and the other frags
are still in unsent outq, if they are abandoned/dropped, the peer would
never get this msg reassembled.

So these frags in unsent outq can't be dropped if this msg already has
outstanding frags.

This patch does the check in sctp_chunk_abandoned and
sctp_prsctp_prune_unsent.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As rfc3758#section-3.1 demands:

   A3) When a TSN is "abandoned", if it is part of a fragmented message,
       all other TSN's within that fragmented message MUST be abandoned
       at the same time.

Besides, if it couldn't handle this, the rest frags would never get
assembled in peer side.

This patch supports it by adding abandoned flag in sctp_datamsg, when
one chunk is being abandoned, set chunk->msg->abandoned as well. Next
time when checking for abandoned, go checking chunk->msg->abandoned
first.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now outstanding_bytes is only increased when appending chunks into one
packet and sending it at 1st time, while decreased when it is about to
move into retransmit queue. It means outstanding_bytes value is already
decreased for all chunks in retransmit queue.

However sctp_prsctp_prune_sent is a common function to check the chunks
in both transmitted and retransmit queue, it decrease outstanding_bytes
when moving a chunk into abandoned queue from either of them.

It could cause outstanding_bytes underflow, as it also decreases it's
value for the chunks in retransmit queue.

This patch fixes it by only updating outstanding_bytes for transmitted
queue when pruning queues for prsctp prio policy, the same fix is also
needed in sctp_check_transmitted.

Fixes: 8dbdf1f5 ("sctp: implement prsctp PRIO policy")
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When configuring an IPv6 address mask, we should use SLICE_NUM_MASK as
the mask in order to make sure all bits are masked by the hardware.
Also, we want matching entries to have a CHAIN_ID value set to the same
value as the rule index we return to user-space for convenience, so fix
that too.

Fixes: ba0696c2 ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Fixes: dd8eff68 ("net: dsa: bcm_sf2: Allow matching arbitrary IPv6 masks/lengths")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After parsing the sit netlink change info, we forget to update frag_off in
ipip6_tunnel_update(). Fix it by assigning frag_off with new value.
Reported-by: NJianlin Shi <jishi@redhat.com>
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_v6_send_reset() expects to receive an skb with skb->cb[] layout as
used in TCP stack.
MD5 lookup uses tcp_v6_iif() and tcp_v6_sdif() and thus
TCP_SKB_CB(skb)->header.h6

This patch probably fixes RST packets sent on behalf of a timewait md5
ipv6 socket.

Before Florian patch, tcp_v6_restore_cb() was needed before jumping to
no_tcp_socket label.

Fixes: 271c3b9b ("tcp: honour SO_BINDTODEVICE for TW_RST case too")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to commit d7fb60b9 ("net_sched: get rid of tcfa_rcu"),
TC actions don't need to respect RCU grace period, because it
is either just detached from tc filter (standalone case) or
it is removed together with tc filter (bound case) in which case
RCU grace period is already respected at filter layer.

Fixes: 5c5670fa ("net/sched: Introduce sample tc action")
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Howells says:

====================
rxrpc: Fixes

Here are three patches for AF_RXRPC.  One removes some whitespace, one
fixes terminal ACK generation and the third makes a couple of places
actually use the timeout value just determined rather than ignoring it.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver expect "allwinner,leds-active-low" to be in PHY node, but
the binding doc expect it to be in MAC node.

Since all board DT use it also in MAC node, the driver need to search
allwinner,leds-active-low in MAC node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reserved and unused fields in the Tx descriptors should be 0. The PPv2
driver doesn't clear them at run-time (for performance reasons) but
these descriptors aren't zeroed when allocated, which can lead to
unpredictable behaviors. This patch fixes this by using
dma_zalloc_coherent instead of dma_alloc_coherent.

Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: NYan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull nfsd fixes from Bruce Fields:
 "I screwed up my merge window pull request; I only sent half of what I
  meant to.

  There were no new features, just bugfixes of various importance and
  some very minor cleanup, so I think it's all still appropriate for
  -rc2.

  Highlights:

   - Fixes from Trond for some races in the NFSv4 state code.

   - Fix from Naofumi Honda for a typo in the blocked lock notificiation
     code

   - Fixes from Vasily Averin for some problems starting and stopping
     lockd especially in network namespaces"

* tag 'nfsd-4.15-1' of git://linux-nfs.org/~bfields/linux: (23 commits)
  lockd: fix "list_add double add" caused by legacy signal interface
  nlm_shutdown_hosts_net() cleanup
  race of nfsd inetaddr notifiers vs nn->nfsd_serv change
  race of lockd inetaddr notifiers vs nlmsvc_rqst change
  SUNRPC: make cache_detail structures const
  NFSD: make cache_detail structures const
  sunrpc: make the function arg as const
  nfsd: check for use of the closed special stateid
  nfsd: fix panic in posix_unblock_lock called from nfs4_laundromat
  lockd: lost rollback of set_grace_period() in lockd_down_net()
  lockd: added cleanup checks in exit_net hook
  grace: replace BUG_ON by WARN_ONCE in exit_net hook
  nfsd: fix locking validator warning on nfs4_ol_stateid->st_mutex class
  lockd: remove net pointer from messages
  nfsd: remove net pointer from debug messages
  nfsd: Fix races with check_stateid_generation()
  nfsd: Ensure we check stateid validity in the seqid operation checks
  nfsd: Fix race in lock stateid creation
  nfsd4: move find_lock_stateid
  nfsd: Ensure we don't recognise lock stateids after freeing them
  ...

Pull btrfs fixes from David Sterba:
 "We've collected some fixes in since the pre-merge window freeze.

  There's technically only one regression fix for 4.15, but the rest
  seems important and candidates for stable.

   - fix missing flush bio puts in error cases (is serious, but rarely
     happens)

   - fix reporting stat::st_blocks for buffered append writes

   - fix space cache invalidation

   - fix out of bound memory access when setting zlib level

   - fix potential memory corruption when fsync fails in the middle

   - fix crash in integrity checker

   - incremetnal send fix, path mixup for certain unlink/rename
     combination

   - pass flags to writeback so compressed writes can be throttled
     properly

   - error handling fixes"

* tag 'for-4.15-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: incremental send, fix wrong unlink path after renaming file
  btrfs: tree-checker: Fix false panic for sanity test
  Btrfs: fix list_add corruption and soft lockups in fsync
  btrfs: Fix wild memory access in compression level parser
  btrfs: fix deadlock when writing out space cache
  btrfs: clear space cache inode generation always
  Btrfs: fix reported number of inode blocks after buffered append writes
  Btrfs: move definition of the function btrfs_find_new_delalloc_bytes
  Btrfs: bail out gracefully rather than BUG_ON
  btrfs: dev_alloc_list is not protected by RCU, use normal list_del
  btrfs: add missing device::flush_bio puts
  btrfs: Fix transaction abort during failure in btrfs_rm_dev_item
  Btrfs: add write_flags for compression bio

Pull Microblaze fix from Michal Simek:
 "Add missing header to mmu_context_mm.h"

* tag 'microblaze-4.15-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: add missing include to mmu_context_mm.h

Pull sparc fix from David Miller:
 "Sparc T4 and later cpu bootup regression fix"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: Fix boot on T4 and later.

Pull networking fixes from David Miller:

 1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
    missed one spot. From Zhu Yanjun.

 2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.

 3) Fix checksum offloading in thunderx driver, from Sunil Goutham.

 4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.

 5) Fix use after free of packet headers in TIPC, from Jon Maloy.

 6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.

 7) Tunneling fixes in mlxsw driver, from Petr Machata.

 8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
    Maloney.

 9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
    Dumazet.

10) Fix regression in sch_sfq.c due to one of the timer_setup()
    conversions. From Paolo Abeni.

11) SCTP does list_for_each_entry() using wrong struct member, fix from
    Xin Long.

12) Don't use big endian netlink attribute read for
    IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
    Long.

13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
    adding filters there. From Jiri Pirko.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  ethernet: dwmac-stm32: Fix copyright
  net: via: via-rhine: use %p to format void * address instead of %x
  net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
  myri10ge: Update MAINTAINERS
  net: sched: cbq: create block for q->link.block
  atm: suni: remove extraneous space to fix indentation
  atm: lanai: use %p to format kernel addresses instead of %x
  VSOCK: Don't set sk_state to TCP_CLOSE before testing it
  atm: fore200e: use %pK to format kernel addresses instead of %x
  ambassador: fix incorrect indentation of assignment statement
  vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
  bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
  sctp: use right member as the param of list_for_each_entry
  sch_sfq: fix null pointer dereference at timer expiration
  cls_bpf: don't decrement net's refcount when offload fails
  net/packet: fix a race in packet_bind() and packet_notifier()
  packet: fix crash in fanout_demux_rollover()
  sctp: remove extern from stream sched
  sctp: force the params with right types for sctp csum apis
  sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
  ...

If we don't put the NG4fls.o object into the same part of
the link as the generic sparc64 objects for fls() and __fls()
then the relocation in the branch we use for patching will
not fit.

Move NG4fls.o into lib-y to fix this problem.

Fixes: 46ad8d2d ("sparc64: Use sparc optimized fls and __fls for T4 and above")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reported-by: NAnatoly Pugachev <matorola@gmail.com>
Tested-by: NAnatoly Pugachev <matorola@gmail.com>

Instead, just fall back on the new '%p' behavior which hashes the
pointer.

Otherwise, '%pK' - that was intended to mark a pointer as restricted -
just ends up leaking pointers that a normal '%p' wouldn't leak.  Which
just make the whole thing pointless.

I suspect we should actually get rid of '%pK' entirely, and make it just
work as '%p' regardless, but this is the minimal obvious fix.  People
who actually use 'kptr_restrict' should weigh in on which behavior they
want.

Cc: Tobin Harding <me@tobin.cc>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The conditional kallsym hex printing used a special fixed-width '%lx'
output (KALLSYM_FMT) in preparation for the hashing of %p, but that
series ended up adding a %px specifier to help with the conversions.

Use it, and avoid the "print pointer as an unsigned long" code.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull printk pointer hashing update from Tobin Harding:
 "Here is the patch set that implements hashing of printk specifier %p.

  First we have two clean up patches then we do the hashing. Hashing is
  done via the SipHash algorithm. The next patch adds printk specifier
  %px for printing pointers when we _really_ want to see the address i.e
  %px is functionally equivalent to %lx. Final patch in the set fixes
  KASAN since we break it by hashing %p.

  For the record here is the justification for the series:

    Currently there exist approximately 14 000 places in the Kernel
    where addresses are being printed using an unadorned %p. This
    potentially leaks sensitive information about the Kernel layout in
    memory. Many of these calls are stale, instead of fixing every call
    we hash the address by default before printing. We then add %px to
    provide a way to print the actual address. Although this is
    achievable using %lx, using %px will assist us if we ever want to
    change pointer printing behaviour. %px is more uniquely grep'able
    (there are already >50 000 uses of %lx).

    The added advantage of hashing %p is that security is now opt-out,
    if you _really_ want the address you have to work a little harder
    and use %px.

  This will of course break some users, forcing code printing needed
  addresses to be updated"

[ I do expect this to be an annoyance, and a number of %px users to be
  added for debuggability. But nobody is willing to audit existing %p
  users for information leaks, and a number of places really only use
  the pointer as an object identifier rather than really 'I need the
  address'.

  IOW - sorry for the inconvenience, but it's the least inconvenient of
  the options.    - Linus ]

* tag 'printk-hash-pointer-4.15-rc2' of git://github.com/tcharding/linux:
  kasan: use %px to print addresses instead of %p
  vsprintf: add printk specifier %px
  printk: hash addresses printed with %p
  vsprintf: refactor %pK code out of pointer()
  docs: correct documentation for %pK

This reverts commit 152e93af.

It was a nice cleanup in theory, but as Nicolai Stange points out, we do
need to make the page dirty for the copy-on-write case even when we
didn't end up making it writable, since the dirty bit is what we use to
check that we've gone through a COW cycle.
Reported-by: NMichal Hocko <mhocko@kernel.org>
Acked-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Uniformize STMicroelectronics copyrights header
Signed-off-by: NBenjamin Gaignard <benjamin.gaignard@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
Acked-by: NAlexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use %x and casting to print out an address, instead use %p
and remove the casting.  Cleans up smatch warnings:

drivers/net/ethernet/via/via-rhine.c:998 rhine_init_one_common()
warn: argument 4 to %lx specifier is cast from pointer
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Values assigned to both variable resend_at and ack_at are overwritten
before they can be used.

The correct fix here is to add 'now' to the previously computed value in
resend_at and ack_at.

Addresses-Coverity-ID: 1462262
Addresses-Coverity-ID: 1462263
Addresses-Coverity-ID: 1462264
Fixes: beb8e5e4 ("rxrpc: Express protocol timeouts in terms of RTT")
Link: https://marc.info/?i=17004.1511808959%40warthog.procyon.org.ukSigned-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

On 64-bit (e.g. powerpc64/allmodconfig):

    drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit_done':
    drivers/net/ethernet/xilinx/ll_temac_main.c:633:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
	dev_kfree_skb_irq((struct sk_buff *)cur_p->app4);
			  ^

cdmac_bd.app4 is u32, so it is too small to hold a kernel pointer.

Note that several other fields in struct cdmac_bd are also too small to
hold physical addresses on 64-bit platforms.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Repeat terminal ACKs and now terminal ACKs are now generated from the
connection event processor rather from call handling as this allows us to
discard client call structures as soon as possible and free up the channel
for a follow on call.

However, in ACKs so generated, the additional information trailer is
malformed because the padding that's meant to be in the middle isn't
included in what's transmitted.

Fix it so that the 3 bytes of padding are included in the transmission.

Further, the trailer is misaligned because of the padding, so assigment to
the u16 and u32 fields inside it might cause problems on some arches, so
fix this by breaking the padding and the trailer out of the packed struct.

(This also deals with potential compiler weirdies where some of the nested
structs are packed and some aren't).

The symptoms can be seen in wireshark as terminal DUPLICATE or IDLE ACK
packets in which the Max MTU, Interface MTU and rwind fields have weird
values and the Max Packets field is apparently missing.
Reported-by: NJeffrey Altman <jaltman@auristor.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Clean up some whitespace from rxrpc.
Signed-off-by: NDavid Howells <dhowells@redhat.com>

Change the maintainer to Chris Lee who has access to Myricom hardware
and can test/review. Update the website URL.
Signed-off-by: NHyong-Youb Kim <hykim@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointers printed with %p are now hashed by default. Kasan needs the
actual address. We can use the new printk specifier %px for this
purpose.

Use %px instead of %p to print addresses.
Signed-off-by: NTobin C. Harding <me@tobin.cc>

printk specifier %p now hashes all addresses before printing. Sometimes
we need to see the actual unmodified address. This can be achieved using
%lx but then we face the risk that if in future we want to change the
way the Kernel handles printing of pointers we will have to grep through
the already existent 50 000 %lx call sites. Let's add specifier %px as a
clear, opt-in, way to print a pointer and maintain some level of
isolation from all the other hex integer output within the Kernel.

Add printk specifier %px to print the actual unmodified address.
Signed-off-by: NTobin C. Harding <me@tobin.cc>