Introduce a new wmi interface controls noise floor (NF) calibration
period via debugfs as firmware has introduced it on v10.2.

It allows users to modify frequency of NF calibration in millisecond
and changes RSSI reporting frequency consequently.
Short calibration period will trigger more frequent NF calibration,
so that RSSI reported in receive frames is more realistic.

Till now calibration was done at 30 seconds.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

New pdev paramters have been added to firmware 10.2,
hence update wmi interfaces to sync with.
Signed-off-by: NPeter Oh <poh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Latest main firmware branch introduced a new WMI
ABI called wmi-tlv. It is not a tlv strictly
speaking but something that resembles it because
it is ordered and may have duplicate id entries.

This prepares ath10k to support new hw.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some functions can be shared across different WMI
ABIs. Make them public so different WMI backends
can use them from different source files in the
future.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since the 10.x fw branch support was introduced it
became apparent ath10k will need to be able to
deal with different fw ABIs eventually.

The patch creates an abstraction for dealing with
command and event structures across different ABIs
and mostly gets rid of the
ATH10K_FW_FEATURE_WMI_10X flag usage.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This splits the actual event parsing into
intermediary structures to facilitate future
support of vastly different ABI WMI backends.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Better to have this in same place as other firmware interface handling.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Instead of using feature flags, add new 32 bit variable for managing different
WMI versions. This makes it firmware interface tests a bit less convoluted,
especially when we add one more interface.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's easier to manage firmware version differences when we configure them in
one place. Rename ath10k_core_init_max_sta_count() to
ath10k_core_init_firmware_features() and start moving most of the firmware
version ("features") handling to that function.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use the error handling style preferred in ath10k. Makes it easier to add
ath10k_init_firmware_features() function in the next patch.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will make it possible to easily support
different hardware with different uart pin
configuration.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to extend the list of
supported hardware.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will make it easier to extend and maintain
list of supported hardware.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds support for reading calibration data from Device Tree.
It looks for the calibration data in Device Tree if it can't find it
in a file. If there's no node in Device Tree, ath10k will try to find the
calibration data from OTP.

The node for the calibration data should be defined like this:

pci {
        pcie@0 {
                reg = <0 0 0 0 0>;
                #interrupt-cells = <1>;
                #size-cells = <2>;
                #address-cells = <3>;
                device_type = "pci";

                ath10k@0,0 {
                        reg = <0 0 0 0 0>;
                        device_type = "pci";
                        qcom,ath10k-calibration-data = [ 01 02 03 ... ];
                };
        };
};
Signed-off-by: NToshi Kikuchi <toshik@chromium.org>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Document how calibration data can be provided to ath10k via Device Tree.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Hardware doesn't place any restrictions on the buffer alignment,
consider this TODO resolved.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If card reset with firmware download executed, followed by reset
with use of firmware from build in flash, firmware download indication
remains in the hardware register.
When running firmware download flow,
the SW download indication is written by the driver to bit 0 in usage_6:
wil_fw_load(), "S(RGF_USER_USAGE_6, 1);"
This register, like all USER RGF, wasn't reset in SW reset flow.
Therefore the driver must clear it on SW reset flow.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the wil_tx_ring, error message printed when tx attempted
while vring has no space to accommodate all fragments of frame.
Normally, such situation handled by stopping tx queue.
But, if tx queue is by-passed (like pktgen does), this error
will be triggered at high rate and dmesg will be flooded with
this message. Whole system may become unstable and hang with
no possible recover except power cycle.

Rate-limit it to prevent dmesg flooding.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In some compilation environments, result of pointer arithmetic interpreted as int
while in others it is long int. Force conversion to long.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow to configure VRING size for both Rx and Tx via module parameters:
rx_ring_order and tx_ring_order. Parameters are ring size orders, i.e.
ring size calculated as 1 << order.
Defaults for both Tx and Rx are order 9, i.e. size 512
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to obtain physical device through
wil->pdev->dev path, as it is done by this macro.
The same device already stored as wiphy's device, thus
wil_to_dev() returns the same device as wil_to_pcie_dev()

Remove unnecessary macros, this allows to drop dependency
by pci.h in the firmware download code.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Scan timeout treated as indication for firmware error;
and should be handled in the same way.

Recovery state machine does not perform as designed because
its state is not updated in case of scan timeout.

Fix is to set recovery state machine into the proper state.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

RX_HTRSH interrupt is handled in exactly the same manner
as RX_DONE interrupt - fetching accumulated packets from RX
ring. In addition there's a rate limitted warning message.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Propagate reason for the disconnect through the relevant call chains:
- report to cfg80211 reason as reported by the firmware
- provide to the firmware reason as requested by cfg80211
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of killing interrupts during reset when the first one happens,
kill them before issuing the reset.
This fixes an easy to reproduce crash with multiple cards sharing the
same IRQ.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Closes another small IRQ handler race
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IRQs are suppressed if ah == NULL and ATH_OP_INVALID being set in
common->op_flags. Close a short time window between those two.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Like with ath9k, ath5k queues also need to be ordered by priority.
queue_info->tqi_subtype already contains the correct index, so use it
instead of relying on the order of ath5k_hw_setup_tx_queue calls.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hardware queues are ordered by priority. Use queue index 0 for BK, which
has lower priority than BE.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver passes the desired hardware queue index for a WMM data queue
in qinfo->tqi_subtype. This was ignored in ath9k_hw_setuptxqueue, which
instead relied on the order in which the function is called.

Cc: stable@vger.kernel.org
Reported-by: NHubert Feurstein <h.feurstein@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The brcms_c_attach_malloc() function can call this with a NULL
"wlc->corestate" or "wlc->hw".

Also I threw in a bonus cleanup by deleting an obvious comment and a
no-op NULL assignment.  :)
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 2ad69ac5. It
causes wireless device disappear when we get -EPROTO error form USB
request. I encounter such situation occasionally when resume form
suspend with RT3070 adapter:

[  289.619985] ieee80211 phy0: rt2x00usb_vendor_request: Error - Vendor Request 0x06 failed for offset 0x0404 with error -71
[  289.639368] ieee80211 phy0: rt2800_wait_bbp_ready: Error - BBP register access failed, aborting
[  289.639374] ieee80211 phy0: rt2800usb_set_device_state: Error - Device failed to enter state 4 (-5)

Without the patch, except printing error, device works just fine after
resume.

Currently after timeouts and REGISTER_BUSY_COUNT tuning, we should
not have any "endless loop", though we can wait quite long when driver
is trying to communicate with the device through non functioning USB
connection. Generally the problem that commit 2ad69ac5 solves
is kinda artificial.

Cc: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Waiting 500ms for register access is too long, decrease this value
to 100ms.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Because of delays on USB we do not have to iterate so many times on
USB hardware when waiting for H/W register become valid.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use provided timeout value in rt2x00usb_vendor_request() instead
of iterating REGISTER_BUSY_COUNT times.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware info now also include radio and phy information, which
can be helpful in debugging issues.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The board revision that is available in hardware can be translated
so it matches the labelling on the board. This is accomplished by
this helper function.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently implemented temperature compensation is only valid on some of
supported chips. Other chips do not need temperature compensation or
need different way to do this (not yet implemented in the rt2800
driver). Trying to do run rt2800_get_gain_calibration_delta() when this
is not appropriate on particular chip gives bogus result of TX power
and can make connection unstable.

This is follow up to commit 8c8d2017
"rt2800: fix RT5390 & RT3290 TX power settings regression". On that
commit we avoid setting BBP_R1 register, but the real problem is wrong
temperature compensation calculation.
Reported-and-tested-by: NRonald Wahl <ronald.wahl@raritan.com>
Debugged-by: NRonald Wahl <ronald.wahl@raritan.com>
Cc: Mike Romberg <mike-romberg@comcast.net>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix missing memory deallocation on error paths in wil_write_file_wmi()
and wil_write_file_txmgmt().
Reported-by: NAhmed Tamrawi <ahmedtamrawi@gmail.com>
Signed-off-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>