When suspending an associated system, and then resuming,
the station vif is being reconfigured without taking the
sdata->u.mgd.mtx lock, which results in the following warning:

WARNING: at net/mac80211/mlme.c:101 ieee80211_ap_probereq_get+0x58/0xb8 [mac80211]()
Modules linked in: wl12xx_sdio wl12xx firmware_class crc7 mac80211 cfg80211 [last unloaded: crc7]
Backtrace:
[<c005432c>] (dump_backtrace+0x0/0x118) from [<c0376e28>] (dump_stack+0x20/0x24)
 r7:00000000 r6:bf12d6ec r5:bf154aac r4:00000065
[<c0376e08>] (dump_stack+0x0/0x24) from [<c0079104>] (warn_slowpath_common+0x5c/0x74)
[<c00790a8>] (warn_slowpath_common+0x0/0x74) from [<c0079148>] (warn_slowpath_null+0x2c/0x34)
 r9:000024ff r8:cd006460 r7:00000001 r6:00000000 r5:00000000
r4:cf1394a0
[<c007911c>] (warn_slowpath_null+0x0/0x34) from [<bf12d6ec>] (ieee80211_ap_probereq_get+0x58/0xb8 [mac80211])
[<bf12d694>] (ieee80211_ap_probereq_get+0x0/0xb8 [mac80211]) from [<bf19cd04>] (wl1271_cmd_build_ap_probe_req+0x30/0xf8 [wl12xx])
 r4:cd007440
[<bf19ccd4>] (wl1271_cmd_build_ap_probe_req+0x0/0xf8 [wl12xx]) from [<bf1995f4>] (wl1271_op_bss_info_changed+0x4c4/0x808 [wl12xx])
 r5:cd007440 r4:000003b4
[<bf199130>] (wl1271_op_bss_info_changed+0x0/0x808 [wl12xx]) from [<bf122168>] (ieee80211_bss_info_change_notify+0x1a4/0x1f8 [mac80211])
[<bf121fc4>] (ieee80211_bss_info_change_notify+0x0/0x1f8 [mac80211]) from [<bf141e80>] (ieee80211_reconfig+0x4d0/0x668 [mac80211])
 r8:cf0eeea4 r7:cd00671c r6:00000000 r5:cd006460 r4:cf1394a0
[<bf1419b0>] (ieee80211_reconfig+0x0/0x668 [mac80211]) from [<bf137dd4>] (ieee80211_resume+0x60/0x70 [mac80211])
[<bf137d74>] (ieee80211_resume+0x0/0x70 [mac80211]) from [<bf0eb930>] (wiphy_resume+0x6c/0x7c [cfg80211])
 r5:cd006248 r4:cd006110
[<bf0eb8c4>] (wiphy_resume+0x0/0x7c [cfg80211]) from [<c0241024>] (legacy_resume+0x38/0x70)
 r7:00000000 r6:00000000 r5:cd006248 r4:cd0062fc
[<c0240fec>] (legacy_resume+0x0/0x70) from [<c0241478>] (device_resume+0x168/0x1a0)
 r8:c04ca8d8 r7:cd00627c r6:00000010 r5:cd006248 r4:cd0062fc
[<c0241310>] (device_resume+0x0/0x1a0) from [<c0241600>] (dpm_resume_end+0xf8/0x3bc)
 r7:00000000 r6:00000005 r5:cd006248 r4:cd0062fc
[<c0241508>] (dpm_resume_end+0x0/0x3bc) from [<c00b2a24>] (suspend_devices_and_enter+0x1b0/0x204)
[<c00b2874>] (suspend_devices_and_enter+0x0/0x204) from [<c00b2b68>] (enter_state+0xf0/0x148)
 r7:c037e978 r6:00000003 r5:c043d807 r4:00000000
[<c00b2a78>] (enter_state+0x0/0x148) from [<c00b20a4>] (state_store+0xa4/0xcc)
 r7:c037e978 r6:00000003 r5:00000003 r4:c043d807
[<c00b2000>] (state_store+0x0/0xcc) from [<c01fc90c>] (kobj_attr_store+0x20/0x24)
[<c01fc8ec>] (kobj_attr_store+0x0/0x24) from [<c0157120>] (sysfs_write_file+0x11c/0x150)
[<c0157004>] (sysfs_write_file+0x0/0x150) from [<c0100f84>] (vfs_write+0xc0/0x14c)
[<c0100ec4>] (vfs_write+0x0/0x14c) from [<c01010e4>] (sys_write+0x4c/0x78)
 r8:40126000 r7:00000004 r6:cf1a7c80 r5:00000000 r4:00000000
[<c0101098>] (sys_write+0x0/0x78) from [<c00500c0>] (ret_fast_syscall+0x0/0x30)
 r8:c00502c8 r7:00000004 r6:403525e8 r5:40126000 r4:00000004
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599

Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.

For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.

Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: NSilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org  # 2.6.35+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Using skb_header_cloned to check if it's safe to write to the skb is not
enough - mac80211 also touches the tailroom of the skb.
Initially this check was only used to increase a counter, however this
commit changed the code to also skip skb data reallocation if no extra
head/tailroom was needed:

commit 4cd06a34
mac80211: skip unnecessary pskb_expand_head calls

It added a regression at least with iwl3945, which is fixed by this patch.
Reported-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Tested-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With commit 554d1d02 only one RF_KILL
interrupt will be seen by the driver when the interface is down.

Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes parsing of the device invariants (MAC address)
for PCMCIA SSB devices.

ssb_pcmcia_do_get_invariants expects an iv pointer as data
argument.
Tested-by: Ndylan cristiani <d.cristiani@idem-tech.it>
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reverts the following commit
ath9k: remove bfs_paprd_timestamp from struct ath_buf_state

Under high interference/noisy environment conditions where PAPRD frames
fails heavily introduces a possibility of double freeing skb's and causes
kernel panic after some time.This patch reverts back to the original approach
of using paprd_timestamp before freeing the PAPRD frame skb's

[  194.193705] Pid: 0, comm: swapper Tainted: G      D WC
2.6.35-22-generic #33-Ubuntu
[  194.193712] Call Trace:
[  194.193722]  [<c05c6468>] ? printk+0x2d/0x35
[  194.193732]  [<c05c63c3>] panic+0x5a/0xd2
[  194.193741]  [<c05ca3ed>] oops_end+0xcd/0xd0
[  194.193750]  [<c0105f74>] die+0x54/0x80
[  194.193758]  [<c05c9a16>] do_trap+0x96/0xc0
[  194.193837]  [<c0103fb0>] ? do_invalid_op+0x0/0xa0
[  194.193846]  [<c010403b>] do_invalid_op+0x8b/0xa0
[  194.193856]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193866]  [<c012ce18>] ? default_spin_lock_flags+0x8/0x10
[  194.193877]  [<c01de47a>] ? free_one_page+0x12a/0x2d0
[  194.193888]  [<c01e04dc>] ? __free_pages+0x1c/0x40
[  194.193897]  [<c05c97a7>] error_code+0x73/0x78
[  194.193906]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193915]  [<c04ecdd0>] ? skb_release_data+0x70/0xa0
[  194.193924]  [<c04ecdd0>] skb_release_data+0x70/0xa0
[  194.193933]  [<c04ec997>] __kfree_skb+0x17/0x90
[  194.193941]  [<c04eca31>] consume_skb+0x21/0x40
[  194.193964]  [<f85e0b70>] ieee80211_tx_status+0x760/0x860 [mac80211]
[  194.193979]  [<f85caddf>] ath_tx_complete_buf+0x1bf/0x2c0 [ath9k]
[  194.193988]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.193997]  [<c04ec40e>] ? skb_queue_tail+0x3e/0x50
[  194.194010]  [<f85cc803>] ath_tx_complete_aggr+0x823/0x940 [ath9k]
[  194.194021]  [<c0108a28>] ? sched_clock+0x8/0x10
[  194.194030]  [<c016bf14>] ? sched_clock_local+0xa4/0x180
[  194.194040]  [<c0139f57>] ? enqueue_sleeper+0x1e7/0x2b0
[  194.194051]  [<c013a194>] ? enqueue_entity+0x174/0x200
[  194.194064]  [<f85ce83d>] ath_tx_edma_tasklet+0x2bd/0x3b0 [ath9k]
[  194.194074]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.194088]  [<f85c7b9f>] ath9k_tasklet+0x9f/0x190 [ath9k]
[  194.194097]  [<c01505d7>] tasklet_action+0xa7/0xb0
[  194.194107]  [<c015127c>] __do_softirq+0x9c/0x1b0
[  194.194117]  [<c01a7f64>] ? irq_to_desc+0x14/0x20
[  194.194126]  [<c0124fc4>] ? ack_apic_level+0x64/0x1f0
[  194.194136]  [<c01513d5>] do_softirq+0x45/0x50
[  194.194145]  [<c0151545>] irq_exit+0x65/0x70
[  194.194153]  [<c05cf665>] do_IRQ+0x55/0xc0
[  194.194162]  [<c016a6c7>] ? hrtimer_start+0x27/0x30
[  194.194171]  [<c0103630>] common_interrupt+0x30/0x38
[  194.194181]  [<c012c21a>] ? native_safe_halt+0xa/0x10
[  194.194268]  [<c010a2f9>] default_idle+0x49/0xb0
[  194.194277]  [<c0101fcc>] cpu_idle+0x8c/0xd0
[  194.194286]  [<c05b2431>] rest_init+0x71/0x80
[  194.194295]  [<c081981a>] start_kernel+0x36e/0x374
[  194.194305]  [<c08199dd>] ? pass_all_bootoptions+0x0/0xa
[  194.194314]  [<c08190d7>] i386_start_kernel+0xd7/0xdf
[  194.194364] panic occurred, switching back to text console
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.

Cc: <stable@kernel.org>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the off-channel TX is done with remain-on-channel
offloaded to hardware, the reported cookie is wrong as
in that case we shouldn't use the SKB as the cookie but
need to instead use the corresponding r-o-c cookie
(XOR'ed with 2 to prevent API mismatches).

Fix this by keeping track of the hw_roc_skb pointer
just for the status processing and use the correct
cookie to report in this case. We can't use the
hw_roc_skb pointer itself because it is NULL'ed when
the frame is transmitted to prevent it being used
twice.

This fixes a bug where the P2P state machine in the
supplicant gets stuck because it never gets a correct
result for its transmitted frame.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a minor issue that two connection responses will be sent
for one L2CAP connection request. If the L2CAP connection request is first
blocked due to security reason and responded with reason "security block",
the state of the connection remains BT_CONNECT2. If a pairing procedure
completes successfully before the ACL connection is down, local host will
send another connection complete response. See the following packets
captured by hcidump.

2010-12-07 22:21:24.928096 < ACL data: handle 12 flags 0x00 dlen 16
    0000: 0c 00 01 00 03 19 08 00  41 00 53 00 03 00 00 00  ........A.S.....
... ...

2010-12-07 22:21:35.791747 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 12
... ...

2010-12-07 22:21:35.872372 > ACL data: handle 12 flags 0x02 dlen 16
    L2CAP(s): Connect rsp: dcid 0x0054 scid 0x0040 result 0 status 0
      Connection successful
Signed-off-by: NLiang Bao <tim.bao@gmail.com>
Acked-by: NVille Tervo <ville.tervo@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.

This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/Signed-off-by: NMathias Krause <minipli@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.

This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.

ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.

Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.

Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update maintainer's email address, webpage and align with renaming of
files.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.

Cc: stable@kernel.org
Tested-by: NSujith <m.sujith@gmail.com>
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.

I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2

Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates.  Make it always return cpu-endian values.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue.  As a result, we may not actually stop some queues during
reset.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: NChaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the btusb.c blacklist [03f0:311d] for Atheros AR9285 Malbec BT
and add to ath3k.c ath3-1.fw (md5:1211fa34c09e10ba48381586b7c3883d)
supported this device.
Signed-off-by: NCho, Yu-Chen <acho@novell.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds the device id for the windy31 USB device to the rt73usb
driver.

Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: NRalf Flaxa <rf@suse.de>
Tested-by: NRalf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.

To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In drivers/net/wireless/rtlwifi/pci.c::_rtl_pci_rx_interrupt() we call
dev_alloc_skb(), which may fail and return NULL, but we do not check the
returned value against NULL before dereferencing the returned pointer.
This may lead to a NULL pointer dereference which means we'll crash - not
good.

In a separate call to dev_alloc_skb(), the debug level is changed so that
the failure message will always be logged.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.

Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.

Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For all the new devices, the sku information should read from EEPROM
but for legacy devices such as 4965, appearly the EEPROM does not
contain the necessary information. so skip the read from EEPROM
and go back to use software configuration.
Reported-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

When there is an existing connection l2cap_check_security needs to be
called to ensure that the security level of the new socket is fulfilled.
Normally l2cap_do_start takes care of this, but that function doesn't
get called for SOCK_RAW type sockets. This patch adds the necessary
l2cap_check_security call to the appropriate branch in l2cap_do_connect.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The logic for determining the needed auth_type for an L2CAP socket is
rather complicated and has so far been duplicated in
l2cap_check_security as well as l2cap_do_connect. Additionally the
l2cap_check_security code was completely missing the handling of
SOCK_RAW type sockets. This patch creates a unified function for the
evaluation and makes l2cap_do_connect and l2cap_check_security use that
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

If an existing connection has a MITM protection requirement (the first
bit of the auth_type) then that requirement should not be cleared by new
sockets that reuse the ACL but don't have that requirement.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This reverts commit 04530982. That
commit is wrong for two reasons:

- The conn->sec_level shouldn't be updated without performing
authentication first (as it's supposed to represent the level of
security that the existing connection has)

- A higher auth_type value doesn't mean "more secure" like the commit
seems to assume. E.g. dedicated bonding with MITM protection is 0x03
whereas general bonding without MITM protection is 0x04. hci_conn_auth
already takes care of updating conn->auth_type so hci_connect doesn't
need to do it.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Fix a bug introduced in commit 9cf5b0ea:
function rfcomm_recv_ua calls rfcomm_session_put without checking that
the session is not referenced by some DLC. If the session is freed, that
DLC would refer to deallocated memory, causing an oops later, as shown
in this bug report: https://bugzilla.kernel.org/show_bug.cgi?id=15994Signed-off-by: NLukas Turek <8an@praha12.net>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The blacklist should be freed before the hci device gets unregistered.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

CC: Marcel Holtmann <marcel@holtmann.org>
CC: "Gustavo F. Padovan" <padovan@profusion.mobi>
CC: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

There is no need to hold the firmware in memory.
Signed-off-by: NAlexander Holler <holler@ahsoftware.de>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>