Synchronize PCIe PHY initialization with vendor driver version 8.047.01.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper for MAC OCP read-modify-write operations.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This code piece was inherited from RTL8139 code, the register at
address 0x5c however has a different meaning on RTL8169 and is unused.
So we can remove this.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 171a9bae ("staging/octeon: Allow test build on
!MIPS"), the following combination of configs cause a few Kconfig
warnings and build errors (distilled from arm allyesconfig and Randy's
randconfig builds):

    CONFIG_NETDEVICES=y
    CONFIG_STAGING=y
    CONFIG_COMPILE_TEST=y

and CONFIG_OCTEON_ETHERNET as either a module or built-in.

WARNING: unmet direct dependencies detected for MDIO_OCTEON
  Depends on [n]: NETDEVICES [=y] && MDIO_DEVICE [=y] && MDIO_BUS [=y]
&& 64BIT [=n] && HAS_IOMEM [=y] && OF_MDIO [=n]
  Selected by [y]:
  - OCTEON_ETHERNET [=y] && STAGING [=y] && (CAVIUM_OCTEON_SOC ||
COMPILE_TEST [=y]) && NETDEVICES [=y]

In file included from ../drivers/net/phy/mdio-octeon.c:14:
../drivers/net/phy/mdio-cavium.h:111:36: error: implicit declaration of
function ‘writeq’; did you mean ‘writel’?
[-Werror=implicit-function-declaration]
  111 | #define oct_mdio_writeq(val, addr) writeq(val, (void *)addr)
      |                                    ^~~~~~

CONFIG_64BIT is not strictly necessary if the proper readq/writeq
definitions are included from io-64-nonatomic-lo-hi.h.

CONFIG_OF_MDIO is not needed when CONFIG_COMPILE_TEST is enabled because
of commit f9dc9ac5 ("of/mdio: Add dummy functions in of_mdio.h.").

Fixes: 171a9bae ("staging/octeon: Allow test build on !MIPS")
Reported-by: Nkbuild test robot <lkp@intel.com>
Reported-by: NMark Brown <broonie@kernel.org>
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This Kconfig option is unused, drop it.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge the two headers into one, no functional change.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove ksz_port_cleanup(), which is unused. Add missing include
"ksz_common.h", which fixes the following warning when built with
make ... W=1

drivers/net/dsa/microchip/ksz_common.c:23:6: warning: no previous prototype for ‘...’ [-Wmissing-prototypes]

Note that the order of the headers cannot be swapped, as that would
trigger missing forward declaration errors, which would indicate the
way forward is to merge the two headers into one.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is relying on zero'ed allocated memory and does not
explicitly call atomic_set() to initialize the ref counts to 0.  Add
these atomic_set() calls so that it will be more straight forward
to convert atomic ref counts to refcount_t.
Reported-by: NChuhong Yuan <hslester96@gmail.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: <GR-Linux-NIC-Dev@marvell.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ENETC ports can manage the MDIO bus via local register
interface.  However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).

Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers.  For instance, on the LS1028A QDS board
where MDIO muxing is required.  Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.

The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access.  It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules.  This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.

Fixes following sparse warning:
 warning: incorrect type in assignment (different address spaces)
    expected void *priv
    got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs

Fixes: ebfcb23d ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: NClaudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds PTP support for the MV88E6250 family.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As it is done for all the other structs within this driver.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.

If a user configures an invalid port, an error is returned.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: NHubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ensures we can talk to a PHY via MDIO on the AST2600, as the MDIO
controller is now separate from the MAC.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy-handle is necessary for the AST2600 which separates the MDIO
controllers from the MAC.

I've tried to minimise the intrusion of supporting the AST2600 to the
FTGMAC100 by leaving in place the existing MDIO support for the embedded
MDIO interface. The AST2400 and AST2500 continue to be supported this
way, as it avoids breaking/reworking existing devicetrees.

The AST2600 support by contrast requires the presence of the phy-handle
property in the MAC devicetree node to specify the appropriate PHY to
associate with the MAC. In the event that someone wants to specify the
MDIO bus topology under the MAC node on an AST2400 or AST2500, the
current auto-probe approach is done conditional on the absence of an
"mdio" child node of the MAC.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The AST2600 design separates the MDIO controllers from the MAC, which is
where they were placed in the AST2400 and AST2500. Further, the register
interface is reworked again, so now we have three possible different
interface implementations, however this driver only supports the
interface provided by the AST2600. The AST2400 and AST2500 will continue
to be supported by the MDIO support embedded in the FTGMAC100 driver.

The hardware supports both C22 and C45 mode, but for the moment only C22
support is implemented.
Signed-off-by: NAndrew Jeffery <andrew@aj.id.au>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce the scope of the ring local variable in the fm10k_assign_l2_accel
function.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[fm10k_netdev.c:1447]: (style) The scope of the variable 'ring' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the result local variable in the
fm10k_iov_msg_lport_state_pf function.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[fm10k_pf.c:1435]: (style) The scope of the variable 'result' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The msg variable in the fm10k_mbx_validate_msg_size and
fm10k_sm_mbx_transmit functions is only used within the do {} loop
scope. Reduce its scope only to where it is used.

This was detected by cppcheck, and resolves the following warnings
produced by that tool:

[fm10k_mbx.c:299]: (style) The scope of the variable 'msg' can be reduced.
[fm10k_mbx.c:2004]: (style) The scope of the variable 'msg' can be reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the local loop variable in the
fm10k_check_hang_subtask function.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[driver/fm10k_pci.c:852]: (style) The scope of the variable 'i' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the local variable err in the fm10k_detach_subtask
function.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[fm10k_pci.c:403]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The tx_buffer local variable in the function fm10k_clean_tx_ring is not
used except inside a smaller block scope. Reduce the scope to its point
of use.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_netdev.c:179]: (style) The scope of the variable 'tx_buffer' can
be reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the q_idx local variable in the fm10k_cache_ring_qos
function.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_main.c:2016]: (style) The scope of the variable 'q_idx' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the local err variable in the fm10k_iov_alloc_data
function.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_iov.c:426]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the qv vector pointer local variable in the
fm10k_set_coalesce function.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_ethtool.c:658]: (style) The scope of the variable 'qv' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the char *p local variable to only the block where
it is used.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_ethtool.c:229]: (style) The scope of the variable 'p' can be
reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Reduce the scope of the err local variable in the fm10k_dcbnl_ieee_setets
function.

This was detected using cppcheck, and resolves the following style
warning:

[fm10k_dcbnl.c:37]: (style) The scope of the variable 'err' can be reduced.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read and
_mv88e6xxx_port_vlan_add is the only function requiring the preparation
of a new VLAN entry.

To simplify things up, remove the mv88e6xxx_vtu_get wrapper and
explicit the VLAN lookup in _mv88e6xxx_port_vlan_add. This rework
also avoids programming the broadcast entries again when changing a
port's membership, e.g. from tagged to untagged.

At the same time, rename the helper using an old underscore convention.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrapping mv88e6xxx_vtu_getnext makes the code less easy to read.
Explicit the call to mv88e6xxx_vtu_getnext in _mv88e6xxx_port_vlan_del
and the return value expected by switchdev in case of software VLANs.

At the same time, rename the helper using an old underscore convention.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext is simple enough to call it directly in the
mv88e6xxx_port_db_load_purge function and explicit the return code
expected by switchdev for software VLANs when an hardware VLAN does
not exist.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mv88e6xxx_vtu_getnext interprets two members from the input
mv88e6xxx_vtu_entry structure: the (excluded) vid member to start
the iteration from, and the valid argument specifying whether the VID
must be written or not (only required once at the start of a loop).

Explicit the assignation of these two fields right before calling
mv88e6xxx_vtu_getnext, as it is done in the mv88e6xxx_vtu_get wrapper.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lock the mutex in the mv88e6xxx_port_vlan_prepare function
called by the DSA stack, instead of doing it in the internal
mv88e6xxx_port_check_hw_vlan helper.
Signed-off-by: NVivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some case, we don't want to allow specific tunnel packets
to host that can avoid to take up high CPU (e.g network attacks).
But other tunnel packets which not matched in hardware will be
sent to host too.

    $ tc filter add dev vxlan_sys_4789 \
	    protocol ip chain 0 parent ffff: prio 1 handle 1 \
	    flower dst_ip 1.1.1.100 ip_proto tcp dst_port 80 \
	    enc_dst_ip 2.2.2.100 enc_key_id 100 enc_dst_port 4789 \
	    action tunnel_key unset pipe action drop
Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Remove redundant include files.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When failing to create tx reporter, don't set the reporter's pointer.
Creating a reporter is not mandatory for driver load, avoid
garbage/error pointer.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Return error when failing to create a reporter in devlink. Since
NET_DEVLINK mandatory to MLX5_CORE in Kconfig, returned pointer
can't be NULL and can only hold an error in bad path.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Move vlan checksum fixup flow into mlx5e_skb_padding_csum(), which is
supposed to fixup SKB checksum if needed. And rename
mlx5e_skb_padding_csum() to mlx5e_skb_csum_fixup().
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>