Encoding the cpu family name apparently confuses people when they try to
boot an image on a sub-variant, so encode the specific cpu name and the
silicon rev instead.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When unmasking a GPIO interrupt on a BF54x part, the code will implicitly
ack any pending interrupts.  This is not what unmasking should do and can
cause people to miss interrupts from their devices, so punt the code.
Reported-by: NRutger Hofman <rutger@cs.vu.nl>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

If there was an error in the lower free functions, we need to pass that
back up so the calling process is able to check things.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NAndreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

On bf518-ezbrd with DSA Ethernet switch enabled, on chip MAC is
connecting to phy at address 3.  If allowing the netdevice framework to
probe both 3 phys of the switch when registering MAC phy, phy at address
1 is checked for link active status other than phy at address 3.  If
connecting a cable to port 2 and leave port 1 open, link status in phy
2 and 3 are online, while that in phy 1 is offline.  So, the phy layer
sets wrong offline status to net device on port 3.  In this case, no data
can be transferred via ethernet port 2.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Common code now invokes the linker directly which causes build failures
when using an FDPIC toolchain.  So move the emulation setting out of the
module-specific LDFLAGS and into the common LDFLAGS.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We check its value at runtime, so we want to avoid garbage across runs.
Signed-off-by: NVivi Li <vivi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Otherwise, gdb continue operation after a breakpoint is hit may trap
into endless breakpoint.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When ADEOS and kgdb are both enabled, single step in linux kernel may be
scheduled to Xenomai core after return from interrupt handlers.  This
blocks gdb continue operation after a break point is hit.  So, disable
interrupt when running gdb single step.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When run kgdb testing, it looks like coreb hangs in single step or trap
exception without handling anomaly 05000257 properly on bf561 v0.5.  But,
the anomaly list says it apply to bf561 v0.4 and bellow.  Apply its work
around to 0.5 temporarily until the behavior and the root cause can be
confirmed by the hardware team.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The low level assembly needs to use the pseudo_long_call helper so that
we use the right call insn when doing kernel XIP.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

KGDB single step in SMP kernel may hang forever in flushinv without a
CSYNC ahead.  This is because the core internal write buffers need to
be flushed before invalidating the data cache to make sure the insn
fetch is not out of sync.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SPORT/UART driver doesn't use the secondary channel pins, so don't
try and request them thus keeping other drivers from using them.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

platfrom -> platform

This changes a struct name. The related code is conditionally
compiled and won't work because the include file linux/gpio-decoder.h
is missing, so removing this code would be an even better solution.

If the missing include file is added, it must fix the spelling, too.
Signed-off-by: NStefan Weil <weil@mail.berlios.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

When using an uncached DMA region less than 1 MiB, we try to mask off
the whole last 1 MiB for it.  Unfortunately, this fails as we forgot
to subtract one from the calculated mask, leading to the region still
be marked as cacheable.
Reported-by: NAndrew Rook <andrew.rook@speakerbus.co.uk>
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Since linux-2.6.31, the kernel suspend framework will do disable_irq/enable_irq,
so save/restore irq in standby and suspend to mem callback should be dropped.
Otherwise the common code notices things are enabled and complains.
Signed-off-by: NSteven Miao <realmz6@gmail.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Add more Analog Devices driver entries and refine the differences between
Blackfin-specific code and processor independent drivers.
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Any consumer of dpmc.h expects to use VR_CTL, so also pull in the new
mach/pll.h header for those functions.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Currently, sending an interprocessor interrupt (IPI) requires building up
a message dynamically which means memory allocation.  But often times, we
will want to send an IPI in low level contexts where allocation is not
possible which may lead to a panic().  So create a per-cpu static array
for the message queue and use that instead.

Further, while we have two supplemental interrupts, we are currently only
using one of them.  So use the second one for the most common IPI message
of all -- smp_send_reschedule().  This avoids ugly contention for locks
which in turn would require an IPI message ...

In general, this improves SMP performance, and in some cases allows the
SMP port to work in places it wouldn't before.  Such as the PREEMPT_RT
state where the slab is protected by a per-cpu spin lock.  If the slab
kmalloc/kfree were to put the task to sleep, and that task was actually
the IPI handler, then the system falls down yet again.

After running some various stress tests on the system, the static limit
of 5 messages seems to work.  On the off chance even this overflows, we
simply panic(), and we can review that scenario to see if the limit needs
to be increased a bit more.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Since we're breaking apart some inter-header dependencies to avoid more
circular loops, move the blackfin_core_id() definition to the func that
it is based upon.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The SMP code needs "asmlinkage" which linkage.h provides.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Common code expects these to be defined for SMP ports, so add them.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF561 mem_map.h header has the __ASSEMBLY__/CONFIG_SMP checks out
of order which leads to build errors for assembly code that happens to
include this file.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

This function takes an irq_handler_t function, but the prototype in
the header doesn't match the function definition.  This is due to the
smp headers needing to avoid circular dependencies.  So change the
function to take a simple pointer.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The common asm-generic non-atomic bitops.h defines test_bit() for us, but
we need to use our own version.  So redirect the definition of this func
to avoid having to inline the rest of the asm-generic file.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The cpu maps are defines provided by common linux/cpumask.h, not local
variables.  So stop exporting them locally and include the right header
for their definition.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The external functions are named __raw_xxx, not arch_xxx, so rename the
prototypes to match reality.  This fixes some simple build errors in the
bfin_ksyms.c code which exports these helpers to modules.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than maintain Kconfig entries where people have to enter raw
numbers and hardcode lists of addresses/pins in the driver itself,
push it all to platform resources.  This lets us simplify the driver,
the Kconfig, and gives board porters greater flexibility.

In the process, we need to also start supporting the early platform
interface.  Not a big deal, but it causes the patch to be bigger than
a simple resource relocation.

All the Blackfin boards already have their resources updated and in
place for this change.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Looks like I missed a few new spots when renaming the SICA macros.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

These were only included because of the irq handling of the PLL funcs,
and those PLL funcs have been moved out into their own header now.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The defBF512.h header exists only to include defBF51x_base.h, and it is
the only place where defBF51x_base.h is included.  So move the contents
of the defBF51x_base.h header into the defBF512.h header.

Same situation for the other def/cdef pairs.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The main asm/blackfin.h header will pull in mach/blackfin.h to get
all the fun Blackfin defines.  So having any of the sub-mach headers
trying to include asm/blackfin.h makes no sense -- punt it.

The mach/blackfin.h header takes care of including the part-specific
def headers which in turn will include any other needed def file.
Similarly, it takes care of pulling in the part-specific cdef header.
So move this logic out of the blackfin.h when necessary.

Further, make sure the cdef headers do not waste time including the
def headers again.

Since all parts need the common def/cdef headers, move this logic
out of the part-specific headers and into the mach/blackfin.h file.

Finally, we need to split the BF539 def header since the BF538 does
not have MXVR and we don't want to expose those MMRs.

So now all parts should have the same behavior:
	mach/blackfin.h
		asm/def_LPBlackfin.h
		part-specific def.h
		if ! asm
			asm/cdef_LPBlackfin.h
			part-specific cdef.h
And the sub def/cdef headers only tail into what they need.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We don't want the BF533 to be different in terms of its MMR headers, so
merge the FIO_FLAG helpers back into the normal place.  To avoid circular
dependencies with headers, turn the inline C funcs into CPP defines.  Not
like there will be any code size differences.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Since the SMP code paths tend to compile fail a lot, start a SMP defconfig
so our nightly build tools will automatically test it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We don't want people banging on MMRs directly.  As for the ip0x board,
it shouldn't need to muck with the CS pin directly as the Blackfin SPI
bus master driver takes care of driving this.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>