- 27 10月, 2010 10 次提交
-
-
由 Andrew Morton 提交于
This comment landed in the wrong place. Cc: Andi Kleen <andi@firstfloor.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Miller <davem@davemloft.net> Cc: Eric Paris <eparis@redhat.com> Cc: Jan Engelhardt <jengelh@medozas.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 KAMEZAWA Hiroyuki 提交于
scan_lru_pages returns pfn. So, it's type should be "unsigned long" not "int". Note: I guess this has been work until now because memory hotplug tester's machine has not very big memory.... physical address < 32bit << PAGE_SHIFT. Reported-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Cc: <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.infradead.org/battery-2.6由 Linus Torvalds 提交于
* git://git.infradead.org/battery-2.6: power_supply: Makefile cleanup bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove() power_supply: Introduce maximum current property power_supply: Add types for USB chargers ds2782_battery: Fix units power_supply: Add driver for TWL4030/TPS65950 BCI charger bq20z75: Add support for more power supply properties wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove() jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove() ds2760_battery: Add missing kfree(di) in ds2760_battery_remove() olpc_battery: Fix endian neutral breakage for s16 values ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency pcf50633-charger: Add missing sysfs_remove_group() power_supply: Add driver for TI BQ20Z75 gas gauge IC wm831x_power: Remove duplicate chg mask omap: rx51: Add support for USB chargers power_supply: Add isp1704 charger detection driver
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core由 Linus Torvalds 提交于
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/i7core: (34 commits) i7core_edac: return -ENODEV when devices were already probed i7core_edac: properly terminate pci_dev_table i7core_edac: Avoid PCI refcount to reach zero on successive load/reload i7core_edac: Fix refcount error at PCI devices i7core_edac: it is safe to i7core_unregister_mci() when mci=NULL i7core_edac: Fix an oops at i7core probe i7core_edac: Remove unused member channels in i7core_pvt i7core_edac: Remove unused arg csrow from get_dimm_config i7core_edac: Reduce args of i7core_register_mci i7core_edac: Introduce i7core_unregister_mci i7core_edac: Use saved pointers i7core_edac: Check probe counter in i7core_remove i7core_edac: Call pci_dev_put() when alloc_i7core_dev() failed i7core_edac: Fix error path of i7core_register_mci i7core_edac: Fix order of lines in i7core_register_mci i7core_edac: Always do get/put for all devices i7core_edac: Introduce i7core_pci_ctl_create/release i7core_edac: Introduce free_i7core_dev i7core_edac: Introduce alloc_i7core_dev i7core_edac: Reduce args of i7core_get_onedevice ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6由 Linus Torvalds 提交于
* 'hwpoison' of git://git.kernel.org/pub/scm/linux/kernel/git/ak/linux-mce-2.6: (22 commits) Add _addr_lsb field to ia64 siginfo Fix migration.c compilation on s390 HWPOISON: Remove retry loop for try_to_unmap HWPOISON: Turn addr_valid from bitfield into char HWPOISON: Disable DEBUG by default HWPOISON: Convert pr_debugs to pr_info HWPOISON: Improve comments in memory-failure.c x86: HWPOISON: Report correct address granuality for huge hwpoison faults Encode huge page size for VM_FAULT_HWPOISON errors Fix build error with !CONFIG_MIGRATION hugepage: move is_hugepage_on_freelist inside ifdef to avoid warning Clean up __page_set_anon_rmap HWPOISON, hugetlb: fix unpoison for hugepage HWPOISON, hugetlb: soft offlining for hugepage HWPOSION, hugetlb: recover from free hugepage error when !MF_COUNT_INCREASED hugetlb: move refcounting in hugepage allocation inside hugetlb_lock HWPOISON, hugetlb: add free check to dequeue_hwpoison_huge_page() hugetlb: hugepage migration core hugetlb: redefine hugepage copy functions hugetlb: add allocate function for hugepage migration ...
-
git://github.com/at91linux/linux-2.6-at91由 Linus Torvalds 提交于
* 'for_linus' of git://github.com/at91linux/linux-2.6-at91: AT91: rtc: enable built-in RTC in Kconfig for at91sam9g45 family at91/atmel-mci: inclusion of sd/mmc driver in at91sam9g45 chip and board AT91: pm: make sure that r0 is 0 when dealing with cache operations AT91: pm: use plain cpu_do_idle() for "wait for interrupt" AT91: reset: extend alternate reset procedure to several chips AT91: reset routine cleanup, remove not needed icache flush AT91: trivial: align comment of at91sam9g20_reset with one more tab AT91: Fix AT91SAM9G20 reset as per the errata in the data sheet AT91: add board support for Pcontrol_G20
-
git://gitorious.org/linux-omap-dss2/linux由 Linus Torvalds 提交于
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux: OMAP: DSS2: don't power off a panel twice OMAP: DSS2: OMAPFB: Allow usage of def_vrfb only for omap2,3 OMAP: DSS2: OMAPFB: make VRFB depends on OMAP2,3 OMAP: DSS2: OMAPFB: Allow FB_OMAP2 to build without VRFB arm/omap: simplify conditional OMAP: DSS2: DSI: Remove extra iounmap in error path OMAP: DSS2: Use dss_features framework on DSS2 code OMAP: DSS2: Introduce dss_features files video/omap: remove mux.h include ARM: omap/fb: move get_fbmem_region() to .init.text ARM: omap/fb: move omapfb_reserve_sram to .init.text ARM: omap/fb: move omap_init_fb to .init.text OMAP: DSS2: OMAPFB: swap front and back porches for both hsync and vsync OMAP: DSS2: make filter coefficient tables human readable OMAP: DSS2: Add SPI dependency to Kconfig of ACX565AKM panel
-
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq由 Linus Torvalds 提交于
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq: [CPUFREQ]: x86, cpufreq: Mark longrun_get_policy with __cpuinit. [CPUFREQ] add sampling_down_factor tunable to improve ondemand performance [CPUFREQ] arch/x86/kernel/cpu/cpufreq: Fix unsigned return type [CPUFREQ] drivers/cpufreq: Adjust confusing if indentation
-
git://linux-nfs.org/~bfields/linux由 Linus Torvalds 提交于
* 'for-2.6.37' of git://linux-nfs.org/~bfields/linux: (99 commits) svcrpc: svc_tcp_sendto XPT_DEAD check is redundant svcrpc: no need for XPT_DEAD check in svc_xprt_enqueue svcrpc: assume svc_delete_xprt() called only once svcrpc: never clear XPT_BUSY on dead xprt nfsd4: fix connection allocation in sequence() nfsd4: only require krb5 principal for NFSv4.0 callbacks nfsd4: move minorversion to client nfsd4: delay session removal till free_client nfsd4: separate callback change and callback probe nfsd4: callback program number is per-session nfsd4: track backchannel connections nfsd4: confirm only on succesful create_session nfsd4: make backchannel sequence number per-session nfsd4: use client pointer to backchannel session nfsd4: move callback setup into session init code nfsd4: don't cache seq_misordered replies SUNRPC: Properly initialize sock_xprt.srcaddr in all cases SUNRPC: Use conventional switch statement when reclassifying sockets sunrpc/xprtrdma: clean up workqueue usage sunrpc: Turn list_for_each-s into the ..._entry-s ... Fix up trivial conflicts (two different deprecation notices added in separate branches) in Documentation/feature-removal-schedule.txt
-
git://git.linux-nfs.org/projects/trondmy/nfs-2.6由 Linus Torvalds 提交于
* 'nfs-for-2.6.37' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: net/sunrpc: Use static const char arrays nfs4: fix channel attribute sanity-checks NFSv4.1: Use more sensible names for 'initialize_mountpoint' NFSv4.1: pnfs: filelayout: add driver's LAYOUTGET and GETDEVICEINFO infrastructure NFSv4.1: pnfs: add LAYOUTGET and GETDEVICEINFO infrastructure NFS: client needs to maintain list of inodes with active layouts NFS: create and destroy inode's layout cache NFSv4.1: pnfs: filelayout: introduce minimal file layout driver NFSv4.1: pnfs: full mount/umount infrastructure NFS: set layout driver NFS: ask for layouttypes during v4 fsinfo call NFS: change stateid to be a union NFSv4.1: pnfsd, pnfs: protocol level pnfs constants SUNRPC: define xdr_decode_opaque_fixed NFSD: remove duplicate NFS4_STATEID_SIZE
-
- 26 10月, 2010 30 次提交
-
-
由 Nicolas Ferre 提交于
Enable built-in RTC IP in Kconfig and modify comments and help messages. RTT as RTC is still available but should not be selected in common case. Reported-by: NYegor Yefremov <yegor_sub1@visionsystems.de> Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and board files. This also configures the DMA controller slave interface for at_hdmac dmaengine driver. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
When using CP15 cache operations (c7), we make sure that Rd (r0) is actually 0 as ARM 926 TRM is saying. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
For power management at91_pm_enter() routine, use the cpu_do_idle() for a rock solid "wait for interrupt" implementation. For AT91SAM9 ARM 926 based chips, we can exceed the cache line length as we can access RAM even while in self-refresh mode. We keep plain access to CP15 for at91rm9200 as this feature is not available: instructions have to be in a single cache line. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
Several at91sam9 chips need the alternate reset procedure to be sure to halt SDRAM smoothly before resetting the chip. This is an extension of previous patch "Fix AT91SAM9G20 reset" to all chips affected. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
Generalize assembler reset routine to allow use on several at91sam9 chips. This patch replace double definitions of SDRAM controller registers and RSTC registers with use of classical header files. For this rework, we remove the not needed icache flush as it is already done in the calling function: arm_machine_restart(). Rename at91sam9g20_reset.S to generalize to several chips. Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Nicolas Ferre 提交于
Preparing next patch with longer names Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Peter Horton 提交于
If the SDRAM is not cleanly shutdown before reset it can be left driving the bus, which then stops the bootloader booting from NAND. Signed-off-by: NPeter Horton <phorton@bitbox.co.uk> [nicolas.ferre@atmel.com: change file header line order] Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Peter Gsellmann 提交于
Board is a carrier board for Stamp9G20, with additional peripherals for a building automation system Signed-off-by: NPeter Gsellmann <pgsellmann@portner-elektronik.at> [nicolas.ferre@atmel.com: remove machine_desc.io_pg_offst and .phys_io] Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
-
由 J. Bruce Fields 提交于
The sanity checks here are incorrect; in the worst case they allow values that crash the client. They're also over-reliant on the preprocessor. Signed-off-by: NJ. Bruce Fields <bfields@redhat.com> Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
-
git://android.git.kernel.org/kernel/tegra由 Linus Torvalds 提交于
* 'for-next' of git://android.git.kernel.org/kernel/tegra: spi: tegra: fix error setting on timeout spi: add spi_tegra driver tegra: harmony: enable PCI Express tegra: add PCI Express support tegra: add PCI Express clocks [ARM] tegra: Add APB DMA support [ARM] tegra: Add cpufreq support [ARM] tegra: common: Update common clock init table [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups [ARM] tegra: Add support for reading fuses [ARM] tegra: gpio: Add suspend and wake support [ARM] tegra: pinmux: add safe values, move tegra2, add suspend [ARM] tegra: add suspend and mirror irqs to legacy controller [ARM] tegra: Add legacy irq support [ARM] tegra: update iomap
-
git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: Blackfin: fix inverted anomaly 05000481 logic Blackfin: drop unused irq_panic()/DEBUG_ICACHE_CHECK Blackfin: ppi/spi/twi headers: add missing __BFP undef Blackfin: update defconfigs Blackfin: bfin_twi.h: start a common TWI header netdev: bfin_mac: push settings to platform resources
-
由 Erik Gilling 提交于
avoids derefencing an uninitialized pointer Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701 Signed-off-by: NErik Gilling <konkers@android.com>
-
git://git.monstr.eu/linux-2.6-microblaze由 Linus Torvalds 提交于
* 'next' of git://git.monstr.eu/linux-2.6-microblaze: (42 commits) microblaze: Fix build with make 3.82 fbdev/xilinxfb: Microblaze driver support microblaze: Support C optimized lib functions for little-endian microblaze: Separate library optimized functions microblaze: Support timer on AXI lite microblaze: Add support for little-endian Microblaze microblaze: KGDB little endian support microblaze: Add PVR for endians plus detection net: emaclite: Add support for little-endian platforms microblaze: trivial: Add comment for AXI pvr microblaze: pci-common cleanup microblaze: Support early console on uart16550 microblaze: Do not compile early console support for uartlite if is disabled microblaze: Setup early console dynamically microblaze: Rename all uartlite early printk functions microblaze: remove early printk uarlite console dependency from header microblaze: Remove additional compatible properties microblaze: Remove hardcoded asm instraction for PVR loading microblaze: Use static const char * const where possible microblaze: Define VMALLOC_START/END ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging由 Linus Torvalds 提交于
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits) hwmon: lis3: Release resources in case of failure hwmon: lis3: Short explanations of platform data fields hwmon: lis3: Enhance lis3 selftest with IRQ line test hwmon: lis3: use block read to access data registers hwmon: lis3: Adjust fuzziness for 8 bit device hwmon: lis3: New parameters to platform data hwmon: lis3: restore axis enabled bits hwmon: lis3: Power on corrections hwmon: lis3: Update coordinates at polled device open hwmon: lis3: Cleanup interrupt handling hwmon: lis3: regulator control hwmon: lis3: pm_runtime support Kirkwood: add fan support for Network Space Max v2 hwmon: add generic GPIO fan driver hwmon: (coretemp) fix reading of microcode revision (v2) hwmon: ({core, pkg, via-cpu}temp) remove unnecessary CONFIG_HOTPLUG_CPU ifdefs hwmon: (pkgtemp) align driver initialization style with coretemp hwmon: LTC4261 Hardware monitoring driver hwmon: (lis3) add axes module parameter for custom axis-mapping hwmon: (hp_accel) Add HP Mini 510x family support ...
-
由 David Howells 提交于
In the MN10300 arch, we occasionally see an assertion being tripped in alloc_cwqs() at the following line: /* just in case, make sure it's actually aligned */ ---> BUG_ON(!IS_ALIGNED(wq->cpu_wq.v, align)); return wq->cpu_wq.v ? 0 : -ENOMEM; The values are: wa->cpu_wq.v => 0x902776e0 align => 0x100 and align is calculated by the following: const size_t align = max_t(size_t, 1 << WORK_STRUCT_FLAG_BITS, __alignof__(unsigned long long)); This is because the pointer in question (wq->cpu_wq.v) loses some of its lower bits to control flags, and so the object it points to must be sufficiently aligned to avoid the need to use those bits for pointing to things. Currently, 4 control bits and 4 colour bits are used in normal circumstances, plus a debugging bit if debugging is set. This requires the cpu_workqueue_struct struct to be at least 256 bytes aligned (or 512 bytes aligned with debugging). PERCPU() alignment on MN13000, however, is only 32 bytes as set in vmlinux.lds.S. So we set this to PAGE_SIZE (4096) to match most other arches and stick a comment in alloc_cwqs() for anyone else who triggers the assertion. Reported-by: NAkira Takeuchi <takeuchi.akr@jp.panasonic.com> Signed-off-by: NDavid Howells <dhowells@redhat.com> Acked-by: NMark Salter <msalter@redhat.com> Cc: Tejun Heo <tj@kernel.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 J. Bruce Fields 提交于
The only caller (svc_send) has already checked XPT_DEAD. Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
-
由 J. Bruce Fields 提交于
If any xprt marked DEAD is also left BUSY for the rest of its life, then the XPT_DEAD check here is superfluous--we'll get the same result from the XPT_BUSY check just after. Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
-
由 J. Bruce Fields 提交于
As long as DEAD exports are left BUSY, and svc_delete_xprt is called only with BUSY held, then svc_delete_xprt() will never be called on an xprt that is already DEAD. Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
-
由 J. Bruce Fields 提交于
Once an xprt has been deleted, there's no reason to allow it to be enqueued--at worst, that might cause the xprt to be re-added to some global list, resulting in later corruption. Also, note this leaves us with no need for the reference-count manipulation here. Reviewed-by: NNeilBrown <neilb@suse.de> Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>
-
由 Samu Onkalo 提交于
If lis3lv02d_init_device fails, HW resources were not released properly. In case of failure call release_resources if available. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Mike Frysinger 提交于
No one uses these MMRs so we didn't notice when the anomaly handling logic was inverted. Reported-by: NRobin Getz <robin.getz@analog.com> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Mike Frysinger 提交于
This code was useful during early port development when our icache code wasn't solid, but that ship has sailed long ago, and no code calls this function anymore (irq_panic). So punt it. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Samu Onkalo 提交于
Short documentation at kernel doc format. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NJonathan Cameron <jic23@cam.ac.uk> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Samu Onkalo 提交于
Configure chip to data ready mode in selftest and count received interrupts to see that interrupt line(s) are working. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Samu Onkalo 提交于
Add optional blockread function to interface driver. If available the chip driver uses it for data register access. For 12 bit device it reads 6 bytes to get 3*16bit data. For 8 bit device it reads out 5 bytes since every second byte is dummy. This optimizes bus usage and reduces number of operations and interrupts needed for one data update. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NJonathan Cameron <jic23@cam.ac.uk> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Samu Onkalo 提交于
Default fuziness is set smaller for 8 device. In 12 bit device LSB is quite close to 1 mg (mg = 1 / 1000 of earth gravity). In 8bit device LSB is about 18 mg. Set fuziness to 1 for 8 bit device. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Samu Onkalo 提交于
Added default output data rate setting to platform data. If default rate is 0, reset default value is used. Added control for duration via platform data. Added possibility to configure interrupts to trig on both rising and falling edge. The lis3 WU unit can be configured quite many ways and with some configurations it is quite handy to get coordinate refresh when some event trigs and when it reason goes away. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NJonathan Cameron <jic23@cam.ac.uk> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-
由 Samu Onkalo 提交于
All axis enable bits are set to 0 at module remove. Restore reset default value at init. Signed-off-by: NSamu Onkalo <samu.p.onkalo@nokia.com> Acked-by: NEric Piel <eric.piel@tremplin-utc.net> Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
-