The commit edd4ab05 ("power: max17042_battery: add HEALTH and TEMP_*
properties support") added support for setting voltage and temperature
thresholds with platform data. For DeviceTree default of 0 was always
used.

This caused reporting battery health always as over voltage or
over heated.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: edd4ab05 ("power: max17042_battery: add HEALTH and TEMP_* properties support")
Signed-off-by: NSebastian Reichel <sre@kernel.org>

The fix for NULL pointer exception related to calling uevent for not
finished probe caused to set all writeable properties as non-writeable.
This was caused by checking if property is writeable before the initial
increase of power supply usage counter and in the same time using
wrapper over property_is_writeable(). The wrapper returns ENODEV if the
usage counter is still 0.

The call trace looked like:
  device probe:
    power_supply_register()
      use_cnt = 0;
      device_add()
        create sysfs entries
          power_supply_attr_is_visible()
            power_supply_property_is_writeable()
              if (use_cnt == 0) return -ENODEV;
      use_cnt++;

Replace the usage of wrapper with direct call to property_is_writeable()
from driver. This should be safe call during device probe because
implementations of this callback just return 0/1 for different
properties and they do not access any of the driver's internal data.

Fixes: 8e59c7f2 ("power_supply: Fix NULL pointer dereference during bq27x00_battery probe")
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

If CONFIG_USB_PHY is not enabled, struct notifier_block is not defined and
compilation fails. Therefore, the functions that process USB event
notifications are defined only if CONFIG_USB_PHY is enabled.
There is no need to define these functions if CONFIG_USB_PHY is not
enabled, since no USB notifications are received in this case.
Also, since rt9455_set_boost_voltage_before_boost_mode() function is
called only if USB_EVENT_ID notification is received, this function should
also be defined only if CONFIG_USB_PHY is enabled.
Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

gpio-restart uses a priority of 128 and currently most soc-level restart
mechanisms use the same - with some exceptions even using 192.
But while the soc-level restarts are provided by the soc itself,
gpio-restarts will most of the time be board-specfic and be used
when some special board condition makes the soc-level restart
only a second choice.

The problem at hand manifested itself on the rk3288-veyron devices.
While the soc-level restart can sucessfully restart all other rockchip
boards I have, the veyron devices use an external restart mechanism that
seems to not only reset the soc but also some external needed components.

With both restart handlers having priority 128 in my tests the soc-specific
variant took precedent in all cases. While it could restart the soc
sucessfully in all cases, firmware then got an issue when talking to an
external component, resulting in the device being put into recovery mode.

So, give the board-specific restart handler a slight push and move it
to priority 129 to make it more important than the generic soc-specific
restart-handler.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Smatch static checker correctly detected an impossible condition because
chip_id was declared as u8, instead of int:

drivers/power/bq25890_charger.c:843 bq25890_probe()
warn: impossible condition '(bq->chip_id < 0) => (0-255 < 0)'

Also, while at it, fix the return value too.
Signed-off-by: NLaurentiu Palcu <laurentiu.palcu@intel.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Based on the datasheet found here:
http://www.richtek.com/download_ds.jsp?p=RT9455Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
[added default values to optional properties]
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

My static checker detected double free_irq() in pm860x_charger_remove().
Unloading this module always causes a warning. This patch removes the
first redundant free_irq() call.
Signed-off-by: NTakeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

The initial register reset of BQ24190 generates a charger status change
whose propagation via power_supply_changed is prevented using a flag.
This flag gets never reset so all following events are ignored as well
leading for example to userspace not detecting charger connects/disconnects.

Therefor change the reset condition of first_time flag, so only the
propagation of the first charger status change is prevented.
Signed-off-by: NThomas Elste <thomas.elste@imms.de>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

This patch adds new power supply charger driver support
for X-Power AXP288 PMIC integrated charger.

This driver interfaces with the axp20x mfd driver as a cell
and listens to extcon cable events for setting up charging.
Signed-off-by: NRamakrishna Pallala <ramakrishna.pallala@intel.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

This patch adds the support for following battery properties
to max17042 fuel gauge driver.

POWER_SUPPLY_PROP_TEMP_ALERT_MIN
POWER_SUPPLY_PROP_TEMP_ALERT_MAX
POWER_SUPPLY_PROP_TEMP_MIN
POWER_SUPPLY_PROP_TEMP_MAX
POWER_SUPPLY_PROP_HEALTH
Signed-off-by: NRamakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

More details about the chip can be found here:
http://www.ti.com/product/bq25890Signed-off-by: NLaurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Signed-off-by: NLaurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

The 'parent' argument passed to power_supply_register() is now used to
postpone callbacks to the driver until the driver's probe end.

Pass current device from charger-manager to utilize that. This will move
created power supply from virtual to platform devices.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Use wrappers over get_property() and set_property() internally in power
supply and for sysfs interface. The wrappers provide safe access if
power supply is not yet registered or t is being destroyed.

In case of syfs the theoretical race could happen between ending of
driver's probe and parallel sysfs access:
some_driver_probe()                    userspace
====================================   ===========================
  drv->psy = power_supply_register()
    device_add()
      sysfs entries are created
    atomic_inc(&psy->use_cnt);
                                       store on sysfs attributes
                                         drv->set_property()
                                           dereference of drv->psy
  drv->psy = returned psy;

For leds the race could happen between power supply being destroyed and
ongoing power_supply_changed_work().
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

devm_gpiod_get_optional returns NULL if devm_gpiod_get would return an
ENOENT error pointer.

There is no semantic change intended.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Replace of_property_read_u32() with device_property_read_u32(), which is a
wrapper over ACPI and device tree enumeration methods.
When ACPI enumeration is used, automode is not supported. Therefore,
bq2415x_charger does not update its input current automatically, depending
on the USB port type that is connected to. Input current may be updated via
sysfs.
Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
  "ENOSYS means 'invalid syscall nr' and nothing else"
- remove unnecessary log message
- split lines whose length is greater than 80 characters
- if an arm statement uses braces, add braces to the other arms of the
  respective statement, too
- match alignment with open parenthesis
Signed-off-by: NAnda-Maria Nicolae <anda-maria.nicolae@intel.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Based on the datasheet found here:
http://www.ti.com/lit/ds/symlink/bq24257.pdfSigned-off-by: NLaurentiu Palcu <laurentiu.palcu@intel.com>
Reviewed-by: NKrzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Don't call the power_supply_changed() from power_supply_register() when
parent is still probing because it may lead to accessing parent too
early.

In bq27x00_battery this caused NULL pointer exception because uevent of
power_supply_changed called back the the get_property() method provided
by the driver. The get_property() method accessed pointer which should
be returned by power_supply_register().

Starting from bq27x00_battery_probe():
  di->bat = power_supply_register()
    power_supply_changed()
      kobject_uevent()
        power_supply_uevent()
          power_supply_show_property()
            power_supply_get_property()
              bq27x00_battery_get_property()
                dereference of di->bat which is NULL here

The dereference of di->bat (value returned by power_supply_register())
is the currently visible problem. However calling back the methods
provided by driver before ending the probe may lead to accessing other
driver-related data which is not yet initialized.

The call to power_supply_changed() is postponed till probing ends -
mutex of parent device is released.
Reported-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 297d716f ("power_supply: Change ownership from driver to core")
Tested-By: NDr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Power supply is often registered during probe of a driver. The
power_supply_register() returns pointer to newly allocated structure as
return value. However before returning the power_supply_register()
calls back the get_property() method provided by the driver through
uevent.

In that time the driver probe is still in progress and driver did not
assigned pointer to power supply to its local variables. This leads to
NULL pointer dereference from get_property() function.
Starting from bq27x00_battery_probe():
  di->bat = power_supply_register()
    device_add()
      kobject_uevent()
        power_supply_uevent()
          power_supply_show_property()
            power_supply_get_property()
              bq27x00_battery_get_property()
                dereference of (di->bat) which is NULL here

The first uevent of power supply (the one coming from device creation)
should not call back to the driver. To prevent that from happening,
increment the atomic use counter at the end of power_supply_register().
This means that power_supply_get_property() will return -ENODEV.

IMPORTANT:
The patch has impact on this first uevent sent from power supply because
it will not contain properties from power supply.

The uevent with properties will be sent later after indicating that
power supply has changed. This also has a race now, but will be fixed in
other patches.
Reported-by: NH. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 297d716f ("power_supply: Change ownership from driver to core")
Tested-By: NDr. H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: NSebastian Reichel <sre@kernel.org>

Two watchdog changes that came through different trees had a non
conflicting conflict, that is, one changed the semantics of a variable
but no actual code conflict happened. So the merge appeared fine, but
the resulting code did not behave as expected.

Commit 195daf66 ("watchdog: enable the new user interface of the
watchdog mechanism") changes the semantics of watchdog_user_enabled,
which thereafter is only used by the functions introduced by
b3738d29 ("watchdog: Add watchdog enable/disable all functions").

There further appears to be a distinct lack of serialization between
setting and using watchdog_enabled, so perhaps we should wrap the
{en,dis}able_all() things in watchdog_proc_mutex.

This patch fixes a s2r failure reported by Michal; which I cannot
readily explain. But this does make the code internally consistent
again.
Reported-and-tested-by: NMichal Hocko <mhocko@suse.cz>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull MTD fixes from Brian Norris:
 "Two MTD fixes for 4.1:

   - readtest: the signal-handling code was clobbering the error codes
     we should be handling/reporting in this test, rendering it useless.
     Noticed by Coverity.

   - the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
     revised, so let's change that before 4.1 is minted"

* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
  Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
  mtd: readtest: don't clobber error reports

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.1-rc4.

  All are pretty minor, and have been in linux-next successfully"

* tag 'usb-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb-storage: Add NO_WP_DETECT quirk for Lacie 059f:0651 devices
  Added another USB product ID for ELAN touchscreen quirks.
  xhci: gracefully handle xhci_irq dead device
  xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256
  xhci: fix isoc endpoint dequeue from advancing too far on transaction error
  usb: chipidea: debug: avoid out of bound read
  USB: visor: Match I330 phone more precisely
  USB: pl2303: Remove support for Samsung I330
  USB: cp210x: add ID for KCF Technologies PRN device
  usb: gadget: remove incorrect __init/__exit annotations
  usb: phy: isp1301: work around tps65010 dependency
  usb: gadget: serial: fix re-ordering of tx data
  usb: gadget: hid: Fix static variable usage
  usb: gadget: configfs: Fix interfaces array NULL-termination
  usb: gadget: xilinx: fix devm_ioremap_resource() check
  usb: dwc3: dwc3-omap: correct the register macros

Pull tty/serial fixes from Greg KH:
 "Here's some TTY and serial driver fixes for reported issues.

  All of these have been in linux-next successfully"

* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  pty: Fix input race when closing
  tty/n_gsm.c: fix a memory leak when gsmtty is removed
  Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
  serial: omap: Fix error handling in probe
  earlycon: Revert log warnings

Pull staging / IIO driver fixes from Greg KH:
 "Here's some staging and iio driver fixes to resolve a number of
  reported issues.

  All of these have been in linux-next for a while"

* tag 'staging-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (31 commits)
  iio: light: hid-sensor-prox: Fix memory leak in probe()
  iio: adc: cc10001: Add delay before setting START bit
  iio: adc: cc10001: Fix regulator_get_voltage() return value check
  iio: adc: cc10001: Fix incorrect use of power-up/power-down register
  staging: gdm724x: Correction of variable usage after applying ALIGN()
  iio: adc: cc10001: Fix the channel number mapping
  staging: vt6655: lock MACvWriteBSSIDAddress.
  staging: vt6655: CARDbUpdateTSF bss timestamp correct tsf counter value.
  staging: vt6655: vnt_tx_packet Correct TX order of OWNED_BY_NIC
  staging: vt6655: Fix 80211 control and management status reporting.
  staging: vt6655: implement IEEE80211_TX_STAT_NOACK_TRANSMITTED
  staging: vt6655: device_free_tx_buf use only ieee80211_tx_status_irqsafe
  staging: vt6656: use ieee80211_tx_info to select packet type.
  staging: rtl8712: freeing an ERR_PTR
  staging: sm750: remove incorrect __exit annotation
  iio: kfifo: Set update_needed to false only if a buffer was allocated
  iio: mcp320x: Fix occasional incorrect readings
  iio: accel: mma9553: check input value for activity period
  iio: accel: mma9553: add enable channel for activity
  iio: accel: mma9551_core: prevent buffer overrun
  ...

Pull char/misc fix from Greg KH:
 "Here is one fix, in the extcon subsystem, that resolves a reported
  issue.

  It's been in linux-next for a number of weeks now, sorry for not
  getting it to you sooner"

* tag 'char-misc-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  extcon: usb-gpio: register extcon device before IRQ registration

Pull UML hostfs fix from Richard Weinberger:
 "This contains a single fix for a regression introduced in 4.1-rc1"

* 'for-linus-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  hostfs: Use correct mask for file mode

Pull UBI bufix from Richard Weinberger:
 "This contains a single bug fix for the UBI block driver"

* tag 'upstream-4.1-rc4' of git://git.infradead.org/linux-ubifs:
  UBI: block: Add missing cache flushes

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of ext4 bugs; the most serious of which is a bug in the
  lazytime mount optimization code where we could end up updating the
  timestamps to the wrong inode"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix an ext3 collapse range regression in xfstests
  jbd2: fix r_count overflows leading to buffer overflow in journal recovery
  ext4: check for zero length extent explicitly
  ext4: fix NULL pointer dereference when journal restart fails
  ext4: remove unused function prototype from ext4.h
  ext4: don't save the error information if the block device is read-only
  ext4: fix lazytime optimization

Pull btrfs fixes from Chris Mason:
 "The first commit is a fix from Filipe for a very old extent buffer
  reuse race that triggered a BUG_ON.  It hasn't come up often, I looked
  through old logs at FB and we hit it a handful of times over the last
  year.

  The rest are other corners he hit during testing"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix race when reusing stale extent buffers that leads to BUG_ON
  Btrfs: fix race between block group creation and their cache writeout
  Btrfs: fix panic when starting bg cache writeout after IO error
  Btrfs: fix crash after inode cache writeback failure

Pull MIPS fixes from Ralf Baechle:
 "Seven small fixes.  The shortlog below is a good description so no
  need to elaborate.

  It has sat in linux-next and survived the usual automated testing by
  Imagination's test farm"

* 'master' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: tlb-r4k: Fix PG_ELPA comment
  MIPS: Fix up obsolete cpu_set usage
  MIPS: IP32: Fix build errors in reset code in DS1685 platform hook.
  MIPS: KVM: Fix unused variable build warning
  MIPS: traps: remove extra Tainted: line from __show_regs() output
  MIPS: Fix wrong CHECKFLAGS (sparse builds) with GCC 5.1
  MIPS: Fix a preemption issue with thread's FPU defaults

Pull ARC fixes from Vineet Gupta.

* tag 'arc-4.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: inline cache flush toggle helpers
  ARC: With earlycon in use, retire EARLY_PRINTK
  ARC: unbork !LLSC build

Pull ARM SoC fixes from Arnd Bergmann:
 "Nothing frightening this time, just smaller fixes in a number of
  places.

  The other changes contained here are:

   MAINTAINERS file updates:

   - The mach-gemini maintainer is back in action and has a new git tree

   - Krzysztof Kozlowski has volunteered to be a new co-maintainer for
     the samsung platforms

   - updates to the files that belong to Marvell mvebu

  Bug fixes:

   - The largest changes are on omap2, but are only to avoid some
     harmless warnings and to fix reset on omap4

   - a small regression fix on tegra

   - multiple fixes for incorrect IRQ affinity on vexpress

   - the missing system controller on arm64 juno is added

   - one revert of a patch that was accidentally applied twice for
     mach-rockchip

   - two clock related DT fixes for mvebu

   - a workaround for suspend with old DT binaries on new exynos kernels

   - Another fix for suspend on exynos, needs to be backported"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  MAINTAINERS: Add dts entries for some of the Marvell SoCs
  MAINTAINERS: ARM: EXYNOS: Add Krzysztof Kozlowski as co-maintainer
  ARM: EXYNOS: Use of_machine_is_compatible instead of soc_is_exynos4
  ARM: EXYNOS: Fix failed second suspend on Exynos4
  Revert "ARM: rockchip: fix undefined instruction of reset_ctrl_regs"
  ARM: EXYNOS: Fix dereference of ERR_PTR returned by of_genpd_get_from_provider
  ARM: EXYNOS: Don't try to initialize suspend on old DT
  ARM: dts: Add keep-power-in-suspend to WiFi SDIO node for Peach Boards
  ARM: gemini: fix compiler warning due wrong data type
  ARM: vexpress/tc2: Add interrupt-affinity to the PMU node
  ARM: vexpress/ca9: Add interrupt-affinity to the PMU node
  ARM: vexpress/ca9: Add unified-cache property to l2 cache node
  ARM64: juno: add sp810 support and fix sp804 clock frequency
  ARM: Gemini: Maintainers update
  ARM: OMAP2+: Remove bogus struct clk comparison for timer clock
  ARM: dove: Add clock-names to CuBox Si5351 clk generator
  ARM: AM33xx+: hwmod: re-use omap4 implementations for reset functionality
  ARM: OMAP4+: PRM: add support for passing status register/bit info to reset
  ARM: AM43xx: hwmod: add VPFE hwmod entries
  ARM: mvebu: Fix the main PLL frequency on Armada 375, 38x and 39x SoCs
  ...

Pull thermal fixes from Zhang Rui:
 "Specifics:

   - fix an issue in intel_powerclamp driver that idle injection target
     is not accurately maintained on newer Intel CPUs.  Package C8 to
     C10 states are introduced on these CPUs but they were not included
     in the package c-state residency calculation.  From Jacob Pan.

   - fix a problem that package c-state idle injection was missing on
     Broadwell server, by adding its id to intel_powerclamp driver.
     From Jacob Pan.

   - a couple of small fixes and cleanups from Joe Perches, Mathias
     Krause, Dan Carpenter and Anand Moon"

* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  tools/thermal: tmon: fixed the 'make install' command
  thermal: rockchip: fix an error code
  thermal/powerclamp: fix missing newer package c-states
  thermal/intel_powerclamp: add id for broadwell server
  thermal/intel_powerclamp: add __init / __exit annotations
  thermal: Use bool function return values of true/false not 1/0