Clang static analysis reports this error

drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc.c:2870:7: warning:
Dereference of null pointer [clang-analyzer-core.NullDereference]
                if
(top_pipe_to_program->stream_res.tg->funcs->lock_doublebuffer_enable) {
                    ^

top_pipe_to_program being NULL is caught as an error
But then it is used to report the error.

So add a check before using it.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Signed-off-by: NYang Li <yang.lee@linux.alibaba.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In function dc_sink_destruct, kfree will check pointer, no need
to check again.
This change is to cleanup the code a bit.
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This change is to cleanup the code a bit.
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In function amdgpu_get_xgmi_hive, when kobject_init_and_add failed
There is a potential memleak if not call kobject_put.
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This change is to cleanup the code style a bit.
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This change is to remove useless break after return.
Signed-off-by: NBernard Zhao <bernard@vivo.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This was found by coccicheck:
./drivers/gpu/drm/amd/display/dc/core/dc_resource.c, 2516, 7-9, WARNING
possible condition with no effect (if == else)

hdmi_info.bits.YQ0_YQ1 is always YYC_QUANTIZATION_LIMITED_RANGE.
Reported-by: NZeal Robot <zealci@zte.com.cn>
Signed-off-by: NYe Guojin <ye.guojin@zte.com.cn>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Eliminate the follow smatch warning:

drivers/gpu/drm/amd/amdgpu/../display/dmub/src/dmub_srv.c:622
dmub_srv_cmd_execute() warn: inconsistent indenting.
Reported-by: NAbaci Robot <abaci@linux.alibaba.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NJiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
	(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.
Signed-off-by: Nhongao <hongao@uniontech.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
After commit ("drm/amdgpu/display: add support for multiple backlights")
number of eDPs is defined while registering backlight device.
However the panel's extended caps get updated once before register call.
That leads to regression with extended caps like oled brightness control.

[How]
Update connector ext caps after register_backlight_device

Fixes: 7fd13bae ("drm/amdgpu/display: add support for multiple backlights")
Link: https://www.reddit.com/r/AMDLaptops/comments/qst0fm/after_updating_to_linux_515_my_brightness/Signed-off-by: NRoman Li <Roman.Li@amd.com>
Tested-by: NSamuel Čavoj <samuel@cavoj.net>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NJasdeep Dhillon <Jasdeep.Dhillon@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix race condition failure during UMC UE injection.
Signed-off-by: NCandice Li <candice.li@amd.com>
Reviewed-by: NTao Zhou <tao.zhou1@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If gpu reset is triggered by ras fatal error, tell it to smu in mode-1
reset message.

v2: move mode-1 reset function to aldebaran_ppt.c since it's aldebaran
specific currently.
Signed-off-by: NTao Zhou <tao.zhou1@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

In SRIOV configuration, the reset may failed to bring asic back to normal but stop cpsch
already been called, the start_cpsch will not be called since there is no resume in this
case.  When reset been triggered again, driver should avoid to do uninitialization again.
Signed-off-by: Nshaoyunl <shaoyun.liu@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Print Navi1x fine grained clocks in a consistent manner with other SOCs.
Don't show aritificial DPM level when the current clock equals min or max.
Signed-off-by: NLijo Lazar <lijo.lazar@amd.com>
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Just bail out if the target IP block is already in the desired
powergate/ungate state. This can avoid some duplicate settings
which sometimes may cause unexpected issues.

Link: https://lore.kernel.org/all/YV81vidWQLWvATMM@zn.tnic/
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214921
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=215025
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1789Signed-off-by: NEvan Quan <evan.quan@amd.com>
Tested-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NLijo Lazar <lijo.lazar@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Change causing issue. Need to revert the change.
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NSung Joon Kim <sungkim@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This version brings along following fixes:
- Fix issue that secondary display goes blank on Non DCN31.
- Adjust flushing data in DMCUB
- Revert patches which cause regression in hadnling MPO/Link encoder assignment
- Correct the setting within MSA of DP2.0
- Adjustment for DML isolation
- Fix FIFO erro in fast boot sequence
- Enable DSC over eDP
- Adjust the DSC power off sequence
Reviewed-by: NAric Cyr <aric.cyr@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.

[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on  the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NYi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

 - Fix ARR39-C issue with scaled integer addition in rb func
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[What]
This change allows adjustment to the Visual Confirm
height border.

[Why]
Aids debugging and testing

[How]
Use the existing infrastructure to implement logic to
draw borders
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NHarry VanZyllDeJong <hvanzyll@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
With eDP DSC enabled and set 4K 60Hz, there would be screen
corruption when booting to OS or enabling the driver.

[HOW]
Avoid powering down VDD when we cannot apply eDP fast boot.
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NBrandon Syu <Brandon.Syu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled

[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Previous LTTPR change has caused a regression that led to an
issue where LTTPR is disabled

[HOW]
Extended changes from previous fix to DCN30X
Reviewed-by: NWesley Chalmers <wesley.chalmers@amd.com>
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NQingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: NAngus Wang <angus.wang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In fast boot sequence, when change dispclk, otg is disabled but digfe
is enabled. This may cause dig fifo error.

[How]
Reset dig fifo after enable otg.
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NJinZe.Xu <JinZe.Xu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
DML itself is SW only, putting the logic as part of resource makes it
hw dependent and thus impossible to compile separately from dc.
Separate compilation is critical for unit testing as well as bbox tool
development

[how]
create new dml wrapper.
Copy logic from the validation functions into dml wrapper as base
implementation. Dml wrapper has internal/static implementations
for all helpers, and does not reference other functions.
It may reference dc structures/types for convenience.

This change now has all the changes for DML isolation squashed into
one.
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NJun Lei <jun.lei@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
There is a bug in MSA programming sequence that mistakenly set
MSA vsp/hsp to 1 for positive polarity. This is incorrect.
Reviewed-by: NAriel Bernstein <Eric.Bernstein@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NWenjing Liu <wenjing.liu@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
The previous changes for fixing MPO underflow with multiple
display connected caused a regression where the machine runs
into a hang when doing multiple driver pnp with multiple displays
connected

[HOW]
Reverted offending change
Reviewed-by: NMartin Leung <Martin.Leung@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NAngus Wang <angus.wang@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
We're currently flushing commands that had been previously been
flushed or are currently being processed by the DMCUB when we don't
immediately wait for idle after command execution.

[How]
Avoiding reflushing the data by keeping track of the last wptr.

We'll treat this as the actual rptr by creating a copy of the inbox
and modifying the copy's rptr.
Reviewed-by: NEric Yang <Eric.Yang2@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Due to integration issues with branch merging,
a regression happened that prevented secondary
displays from lighting up or enabling certain features

[How]
Separated the new logic to be for DCN31 only and retained
pre DCN31 logic for all other ASICs
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NWayne Lin <wayne.lin@amd.com>
Signed-off-by: NAhmad Othman <Ahmad.Othman@amd.com>
Tested-by: NDaniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

MMIO/DOORBELL BOs encode control data and should be pinned in GTT
domain before enabling PCIe connected peer devices in accessing it
Signed-off-by: NRamesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Accounting system to track amount of available memory (system, TTM
and VRAM of a device) relies on BO's domain. The change is to rely
instead on allocation flag indicating BO type - VRAM, GTT, USERPTR,
MMIO or DOORBELL
Signed-off-by: NRamesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Dmesg errors are found on dcn3.1 during reset test, but it's not
a really failure. So reduce it to a debug print.
Signed-off-by: NLeo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
It doesn't make sense to guard DC_LOG_DP2 by CONFIG_DRM_AMD_DCN, and
this also caused build failure for allmodconfig; So drop the guard
to fix the compile failure;
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NLeo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

add support that allow the userspace tool like RGP to get the GFX clock
value at runtime, the fix follow the old way to show the min/current/max
clocks level for compatible consideration.

=== Test ===
$ cat /sys/class/drm/card0/device/pp_dpm_sclk
0: 200Mhz *
1: 1100Mhz
2: 1600Mhz

then run stress test on one APU system.
$ cat /sys/class/drm/card0/device/pp_dpm_sclk
0: 200Mhz
1: 1040Mhz *
2: 1600Mhz

The current GFXCLK value is updated at runtime.

BugLink: https://gitlab.freedesktop.org/mesa/mesa/-/issues/5260Reviewed-by: NHuang Ray <Ray.Huang@amd.com>
Signed-off-by: NPerry Yuan <Perry.Yuan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

asic_family was a duplicate of asic_type, both of type amd_asic_type.
Replace all instances of device_info->asic_family with adev->asic_type
and remove asic_family from device_info.
Signed-off-by: NGraham Sider <Graham.Sider@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Switch to IP version checking instead of asic_type on various KFD
version checks.
Signed-off-by: NGraham Sider <Graham.Sider@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Converts KFD switch statements to use IP version checking instead
of asic_type.
Signed-off-by: NGraham Sider <Graham.Sider@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Defined as GC HWIP >= IP_VERSION(9, 0, 1).

Also defines KFD_GC_VERSION to return GC HWIP version.
Signed-off-by: NGraham Sider <Graham.Sider@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Driver initialization is driven by IP version from IP
discovery table. So add error print when failing to add
ip block during driver initialization, this will be more
friendly to user to know which IP version is not correct.

[   40.467361] [drm] host supports REQ_INIT_DATA handshake
[   40.474076] [drm] add ip block number 0 <nv_common>
[   40.474090] [drm] add ip block number 1 <gmc_v10_0>
[   40.474101] [drm] add ip block number 2 <psp>
[   40.474103] [drm] add ip block number 3 <navi10_ih>
[   40.474114] [drm] add ip block number 4 <smu>
[   40.474119] [drm] add ip block number 5 <amdgpu_vkms>
[   40.474134] [drm] add ip block number 6 <gfx_v10_0>
[   40.474143] [drm] add ip block number 7 <sdma_v5_2>
[   40.474147] amdgpu 0000:00:08.0: amdgpu: Fatal error during GPU init
[   40.474545] amdgpu 0000:00:08.0: amdgpu: amdgpu: finishing device.

v2: use dev_err to multi-GPU system
Signed-off-by: NGuchun Chen <guchun.chen@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>