According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.

From PCIe CEM r2.0, sec 2.6.2

  T-PVPERL: Power stable to PERST# inactive - 100 msec
  T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.

From PCIe r5.0, sec 6.6.1

  With a Downstream Port that does not support Link speeds greater than
  5.0 GT/s, software must wait a minimum of 100 ms before sending a
  Configuration Request to the device immediately below that Port.

Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.

Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.

Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919e ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: NFrancesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Acked-by: NRichard Zhu <hongxing.zhu@nxp.com>

The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.

On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.

Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.

Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244c ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

To balance phy->init_count, invoke the phy_exit() after phy_power_off().

Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244c ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.

Enable the i.MX6QP PCIe suspend/resume operations support.

Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.comSigned-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

The intention of commit 886a9c13 ("PCI: dwc: Move link handling into
common code") was to standardize the behavior of link down as explained
in its commit log:

"The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device."

The pci-imx6 still fails to probe when the link is not present, which
causes the following warning:

imx6q-pcie 8ffc000.pcie: Phy link never came up
imx6q-pcie: probe of 8ffc000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_unbound async_run_entry_fn
[<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14)
[<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70)
[<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154)
[<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8)
[<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc)
[<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c)
[<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178)

Fix this problem by ignoring the dw_pcie_wait_for_link() error like
it is done on the other dwc drivers.

Tested on imx6sx-sdb and imx6q-sabresd boards.

Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com
Fixes: 886a9c13 ("PCI: dwc: Move link handling into common code")
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NRichard Zhu <hongxing.zhu@nxp.com>
Cc: <stable@vger.kernel.org>

i.MX8MM PCIe works mostly like the i.MX8MQ one, but has a different PHY
and allows to output the internal PHY reference clock via the refclk pad.
Add the i.MX8MM PCIe support based on the standalone PHY driver.

Link: https://lore.kernel.org/r/1640312885-31142-2-git-send-email-hongxing.zhu@nxp.comTested-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NTim Harvey <tharvey@gateworks.com>

Previously, the maximum link speed was set following an "fsl,max-link-speed"
property read, and should the read failed, then the PCIe generation was
manually set to PCIe Gen1 and thus limiting the link speed to 2.5 GT/s.

Code refactoring completed in the commit 39bc5006 ("PCI: dwc:
Centralize link gen setting") changed to the logic that was previously
used to limit the maximum link speed leaving behind an unused assignment
to a variable "ret".

Since the value returned from the of_property_read_u32() and stored in
the variable "ret" is never used in any meaningful way, and it's also
immediately reassigned in the code that follows, the assignment can be
removed.

Link: https://lore.kernel.org/r/20211003025439.84783-1-kw@linux.comSigned-off-by: NKrzysztof Wilczyński <kw@linux.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>

The i.MX8MQ PCIe PHY needs 1.8V in default but can be supplied by either a
1.8V or a 3.3V regulator.

The "vph-supply" DT property tells us which external regulator supplies the
PHY. If that regulator supplies anything over 3V, enable the PHY's internal
3.3V-to-1.8V regulator.

Link: https://lore.kernel.org/r/1622771269-13844-3-git-send-email-hongxing.zhu@nxp.comSigned-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers beyond
that point that otherwise would lead to an abort on the i.MX 6QuadPlus.

See commit 075af61c ("PCI: imx6: Limit DBI register length") that
resolves a similar issue on the i.MX 6Quad PCIe.

Link: https://lore.kernel.org/r/1613789388-2495-2-git-send-email-hongxing.zhu@nxp.comSigned-off-by: NRichard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Reviewed-by: NKrzysztof Wilczyński <kw@linux.com>

When devm_ioremap_resource() fails, __devm_ioremap_resource() prints an
error message including the device name, failure cause, and possibly
resource information.

Remove the error message from imx6_pcie_probe() since it's redundant.

Link: https://lore.kernel.org/r/20210511114547.5601-1-thunder.leizhen@huawei.comReported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NZhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NKrzysztof Wilczyński <kw@linux.com>
Acked-by: NRichard Zhu <hongxing.zhu@nxp.com>

Many calls to dw_pcie_host_init() are in a wrapper function with
nothing else now. Let's remove the pointless extra layer.

Link: https://lore.kernel.org/r/20201105211159.1814485-14-robh@kernel.orgTested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com

All RC complex drivers must call dw_pcie_setup_rc(). The ordering of the
call shouldn't be too important other than being after any RC resets.

There's a few calls of dw_pcie_setup_rc() left as drivers implementing
suspend/resume need it.

Link: https://lore.kernel.org/r/20201105211159.1814485-13-robh@kernel.orgTested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Minghuan Lian <minghuan.Lian@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: Roy Zang <roy.zang@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org

The host drivers which call dw_pcie_msi_init() are all the ones using
the built-in MSI controller, so let's move it into the common DWC code.

Link: https://lore.kernel.org/r/20201105211159.1814485-12-robh@kernel.orgTested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org

All the DWC drivers do link setup and checks at roughly the same time.
Let's use the existing .start_link() hook (currently only used in EP
mode) and move the link handling to the core code.

The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device.

Link: https://lore.kernel.org/r/20201105211159.1814485-11-robh@kernel.orgTested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org

Platforms using the built-in DWC MSI controller all have a dedicated
interrupt with "msi" name or at index 0, so let's move setting up the
interrupt to the common DWC code.

spear13xx and dra7xx are the 2 oddballs with muxed interrupts, so
we need to prevent configuring the MSI interrupt by setting msi_irq
to negative.

Link: https://lore.kernel.org/r/20201105211159.1814485-9-robh@kernel.orgTested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NJingoo Han <jingoohan1@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org

keystone would force gen2 if no DT property. Now it relies on the
PCI_EXP_LNKCAP value.

Link: https://lore.kernel.org/r/20200821035420.380495-35-robh@kernel.orgSigned-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org

The i.MX6 driver has its own defines for common PCI config space
registers. It also hard codes the capability register offsets which are
discoverable. Convert it to use the standard register definitions.

Link: https://lore.kernel.org/r/20200821035420.380495-29-robh@kernel.orgSigned-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>

PCIE_LINK_WIDTH_SPEED_CONTROL is already defined in pcie-designware.h,
so remove it from the i.MX6 driver.

Link: https://lore.kernel.org/r/20200821035420.380495-23-robh@kernel.orgSigned-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>

Move the IS_ENABLED(CONFIG_PCI_MSI) check into dw_pcie_msi_init()
instead of duplicating it in all the drivers.

Link: https://lore.kernel.org/r/20200821035420.380495-22-robh@kernel.orgSigned-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Yue Wang <yue.wang@Amlogic.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-amlogic@lists.infradead.org
Cc: linux-arm-kernel@axis.com
Cc: linux-arm-msm@vger.kernel.org

When devm_clk_get() returns -EPROBE_DEFER, i.MX6 PCI driver should
NOT print error message, use dev_err_probe() to handle it.

Link: https://lore.kernel.org/r/1597109364-4739-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: NAnson Huang <Anson.Huang@nxp.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through

Link: https://lore.kernel.org/r/20200722031903.GA3711@embeddedorSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

There is no need to call the dev_err() function directly to print a
custom message when handling an error from either the platform_get_irq() or
platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.

This change is as per suggestions from Coccinelle, e.g.,

  drivers/pci/controller/dwc/pcie-armada8k.c:252:2-9: line 252 is
  redundant because platform_get_irq() already prints an error

[bhelgaas: squashed into one commit]
Suggested-by: NBjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200802142601.1635926-2-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-3-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-4-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-5-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-6-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-7-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-8-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-9-kw@linux.com
Link: https://lore.kernel.org/r/20200802142601.1635926-10-kw@linux.com
Link: https://lore.kernel.org/r/20200803071040.1663662-1-kw@linux.comSigned-off-by: NKrzysztof Wilczyński <kw@linux.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com> # altera
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> # dwc

Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.

Link: https://lore.kernel.org/r/20200722022514.1283916-6-robh@kernel.orgSigned-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NBjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>

Replace http:// links with https:// links.  This reduces the likelihood of
man-in-the-middle attacks when developers open these links.

  Deterministic algorithm:
  For each file:
    If not .svg:
      For each line:
	If doesn't contain `\bxmlns\b`:
	  For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
	    If both the HTTP and HTTPS versions
	    return 200 OK and serve the same content:
	      Replace HTTP with HTTPS.

[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.deSigned-off-by: NAlexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ.  0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.

On failure, return the error number from platform_get_irq*() instead of
making up a new one.

Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: NAman Sharma <amanharitsh123@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>

regulator_get_optional() can fail for a number of reasons besides probe
deferral. It can for example return -ENOMEM if it runs out of memory as
it tries to allocate data structures. Propagating only -EPROBE_DEFER is
problematic because it results in these legitimately fatal errors being
treated as "regulator not specified in DT".

What we really want is to ignore the optional regulators only if they
have not been specified in DT. regulator_get_optional() returns -ENODEV
in this case, so that's the special case that we need to handle. So we
propagate all errors, except -ENODEV, so that real failures will still
cause the driver to fail probe.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NAndrew Murray <andrew.murray@arm.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: kernel@pengutronix.de
Cc: linux-imx@nxp.com

Define the length of the DBI registers and limit config space to its
length. This makes sure that the kernel does not access registers
beyond that point, avoiding the following abort on a i.MX 6Quad:

  # cat /sys/devices/soc0/soc/1ffc000.pcie/pci0000\:00/0000\:00\:00.0/config
  [  100.021433] Unhandled fault: imprecise external abort (0x1406) at 0xb6ea7000
  ...
  [  100.056423] PC is at dw_pcie_read+0x50/0x84
  [  100.060790] LR is at dw_pcie_rd_own_conf+0x44/0x48
  ...
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>

Establishing a PCIe link can take a while; allow asynchronous probing so
that link establishment can happen in the background while other devices
are being probed.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

imx6_pcie_enable_ref_clk() is never called in atomic context, so
there's no need to use udelay(). Replace it with usleep_range().
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Now that driver data has flags variable that can be used to indicate
quirks/features supported we can switch the code to use it instead of
having a special function that does so based on variant alone. No
functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

PHY registers on i.MX6 are 16-bit wide, so we can get rid of explicit
masking if we restrict pcie_phy_read()/pcie_phy_write() to use 'u16'
instead of 'int'. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Simplify pcie_phy_poll_ack() by incorporating shifting into constant
definition and convert the code to use 'bool'. No functional change
intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Simplify the code by incorporating left shifts into constant
definitions as well as using FIELD_PREP/GENMASK. No functional change
intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Avoid using explicit left shifts and convert various definitions to
use BIT() instead. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Both pcie-designware.c and pci-imx6.c contain custom definitions for
PHY debug registers R0/R1 and on top of that there's already a
definition for R0 in pcie-designware.h. Move all of the definitions to
pcie-designware.h. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Code using these constants was removed in commit a7128072 ("PCI:
imx6: Remove LTSSM disable workaround"). No functional change
intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Change error code from -EINVAL to -ETIMEDOUT in
imx6_pcie_wait_for_speed_change() since that error code seems more
appropriate.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

All calls to imx6_pcie_wait_for_link() share the same error path and
the state of PHY debug registers will already be printed there, so
there's no real reason we can't just use dw_pcie_wait_for_link(). Drop
imx6_pcie_wait_for_link() and replace it with dw_pcie_wait_for_link().
Suggested-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org

Make use of regmap_read_poll_timeout() to simplify
imx7d_pcie_wait_for_phy_pll_lock(). No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-pci@vger.kernel.org