The non-mmu and mmu versions of the module loader module.c are
nearly identical. Merge them back to a single module.c. There is
a little bit of re-ordering of the struct and enum definitions in
module.h to keep the ifdefery to a minimum.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

arch/m68k/mm/init_no.c:123: warning: format "%d" expects type "int", but argument 2 has type "long unsigned int"

And use pr_notice() while we're at it.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

This allows to get rid of the casts.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

This patch removes all the module loader hook implementations in the
architecture specific code where the functionality is the same as that
now provided by the recently added default hooks.
Signed-off-by: NJonas Bonn <jonas@southpole.se>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Tested-by: NMichal Simek <monstr@monstr.eu>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

Add tracepoints to trace mmio page fault
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The idea is from Avi:

| We could cache the result of a miss in an spte by using a reserved bit, and
| checking the page fault error code (or seeing if we get an ept violation or
| ept misconfiguration), so if we get repeated mmio on a page, we don't need to
| search the slot list/tree.
| (https://lkml.org/lkml/2011/2/22/221)

When the page fault is caused by mmio, we cache the info in the shadow page
table, and also set the reserved bits in the shadow page table, so if the mmio
is caused again, we can quickly identify it and emulate it directly

Searching mmio gfn in memslots is heavy since we need to walk all memeslots, it
can be reduced by this feature, and also avoid walking guest page table for
soft mmu.

[jan: fix operator precedence issue]
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NJan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Reorganize it for good using the cache
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Use rcu to protect shadow pages table to be freed, so we can safely walk it,
it should run fastly and is needed by mmio page fault
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Now, the spte is just from nonprsent to present or present to nonprsent, so
we can use some trick to set/clear spte non-atomicly as linux kernel does
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Introduce some interfaces to modify spte as linux kernel does:
- mmu_spte_clear_track_bits, it set the spte from present to nonpresent, and
  track the stat bits(accessed/dirty) of spte
- mmu_spte_clear_no_track, the same as mmu_spte_clear_track_bits except
  tracking the stat bits
- mmu_spte_set, set spte from nonpresent to present
- mmu_spte_update, only update the stat bits

Now, it does not allowed to set spte from present to present, later, we can
drop the atomicly opration for X86_32 host, and it is the preparing work to
get spte on X86_32 host out of the mmu lock
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Introduce handle_abnormal_pfn to handle fault pfn on page fault path,
introduce mmu_invalid_pfn to handle fault pfn on prefetch path

It is the preparing work for mmio page fault support
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If the page fault is caused by mmio, the gfn can not be found in memslots, and
'bad_pfn' is returned on gfn_to_hva path, so we can use 'bad_pfn' to identify
the mmio page fault.
And, to clarify the meaning of mmio pfn, we return fault page instead of bad
page when the gfn is not allowd to prefetch
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The idea is from Avi:
| Maybe it's time to kill off bypass_guest_pf=1.  It's not as effective as
| it used to be, since unsync pages always use shadow_trap_nonpresent_pte,
| and since we convert between the two nonpresent_ptes during sync and unsync.
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Split kvm_mmu_free_page to kvm_mmu_isolate_page and
kvm_mmu_free_page

One is used to remove the page from cache under mmu lock and the other is
used to free page table out of mmu lock
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Move counting used shadow pages from commiting path to preparing path to
reduce tlb flush on some paths
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If 'pt_write' is true, we need to emulate the fault. And in later patch, we
need to emulate the fault even though it is not a pt_write event, so rename
it to better fit the meaning
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

gw->pte_access is the final access permission, since it is unified with
gw->pt_access when we walked guest page table:

FNAME(walk_addr_generic):
	pte_access = pt_access & FNAME(gpte_access)(vcpu, pte, true);
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If dirty bit is not set, we can make the pte access read-only to avoid handing
dirty bit everywhere
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

If the page fault is caused by mmio, we can cache the mmio info, later, we do
not need to walk guest page table and quickly know it is a mmio fault while we
emulate the mmio instruction
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Introduce vcpu_mmio_gva_to_gpa to translate the gva to gpa, we can use it
to cleanup the code between read emulation and write emulation
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Set slot bitmap only if the spte is present
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

Properly check the last mapping, and do not walk to the next level if last spte
is met
Signed-off-by: NXiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This patch implements the kvm bits of the steal time infrastructure.
The most important part of it, is the steal time clock. It is an
continuous clock that shows the accumulated amount of steal time
since vcpu creation. It is supposed to survive cpu offlining/onlining.

[marcelo: fix build with CONFIG_KVM_GUEST=n]
Signed-off-by: NGlauber Costa <glommer@redhat.com>
Acked-by: NRik van Riel <riel@redhat.com>
Tested-by: NEric B Munson <emunson@mgebm.net>
CC: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
CC: Peter Zijlstra <peterz@infradead.org>
CC: Avi Kivity <avi@redhat.com>
CC: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Provide additional information on SIGTRAP by using a sig_info signal.
Use TRAP_BRKPT for breakpoints via illegal operation and TRAP_HWBKPT
for breakpoints via program event recording. Provide the address of
the instruction that caused the breakpoint via si_addr.
While we are at it get rid of tracehook_consider_fatal_signal.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

SIGP emerg needs to pass the source vpu adress into __LC_CPU_ADDRESS of the
target guest.
Signed-off-by: NChristian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The cpu measurement alerts that are used for instance by oprofile
for hardware sampling are not turned off on a cpu that is going
offline. Add the appropriate control register bit that should be
disabled to the list.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove outdated bits from the initial cr0 register.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Do not set the cr0 enablement bit for iucv by default in head[31|64].S,
move the enablement to iucv_init in the iucv base layer.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The (un-)register_external_interrupt functions are not race safe if
more than one interrupt handler is added or deleted for an external
interrupt concurrently.

Make the registration / unregistration of external interrupts race safe
by using RCU and a spinlock. RCU is used to avoid a performance penalty
in the external interrupt handler, the register and unregister functions
are protected by the spinlock and are not performance critical.
call_rcu must be used since the SCLP driver uses the interface with
IRQs disabled. Also use the generic list implementation rather than
homebrewn list code.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch removes the mmu reload logic for kvm on s390. Via Martin's
new gmap interface, we can safely add or remove memory slots while
guest CPUs are in-flight. Thus, the mmu reload logic is not needed
anymore.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch removes kvm-s390 internal assumption of a linear mapping
of guest address space to user space. Previously, guest memory was
translated to user addresses using a fixed offset (gmsor). The new
code uses gmap_fault to resolve guest addresses.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch switches kvm from using (Qemu's) user address space to
Martin's gmap address space. This way QEMU does not have to use a
linker script in order to fit large guests at low addresses in its
address space.
Signed-off-by: NCarsten Otte <cotte@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add code that allows KVM to control the virtual memory layout that
is seen by a guest. The guest address space uses a second page table
that shares the last level pte-tables with the process page table.
If a page is unmapped from the process page table it is automatically
unmapped from the guest page table as well.

The guest address space mapping starts out empty, KVM can map any
individual 1MB segments from the process virtual memory to any 1MB
aligned location in the guest virtual memory. If a target segment in
the process virtual memory does not exist or is unmapped while a
guest mapping exists the desired target address is stored as an
invalid segment table entry in the guest page table.
The population of the guest page table is fault driven.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The alignment is missing for various global symbols in s390 assembly code.
With a recent gcc and an instruction like stgrl this can lead to a
specification exception if the instruction uses such a mis-aligned address.

Specify the alignment explicitely and while add it define __ALIGN for s390
and use the ENTRY define to save some lines of code.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The entry to / exit from sie has subtle dependencies to the first level
interrupt handler. Move the sie assembler code to entry64.S and replace
the SIE_HOOK callback with a test and the new _TIF_SIE bit.
In addition this patch fixes several problems in regard to the check for
the_TIF_EXIT_SIE bits. The old code checked the TIF bits before executing
the interrupt handler and it only modified the instruction address if it
pointed directly to the sie instruction. In both cases it could miss
a TIF bit that normally would cause an exit from the guest and would
reenter the guest context.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

When running a kvm guest we can get intercepts for tprot, if the host
page table is read-only or not populated. This patch implements the
most common case (linux memory detection).
This also allows host copy on write for guest memory on newer systems.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Do not trace arch_local_save_flags(), arch_local_irq_*() and friends.
Although they are marked inline, gcc may still make a function out of
them and add it to the pool of functions that are traced by the function
tracer. This can cause undesirable results (kernel panic, triple faults,
etc).

Add the notrace notation to prevent them from ever being traced.

Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

virtio has been so far used only in the context of virtualization,
and the virtio Kconfig was sourced directly by the relevant arch
Kconfigs when VIRTUALIZATION was selected.

Now that we start using virtio for inter-processor communications,
we need to source the virtio Kconfig outside of the virtualization
scope too.

Moreover, some architectures might use virtio for both virtualization
and inter-processor communications, so directly sourcing virtio
might yield unexpected results due to conflicting selections.

The simple solution offered by this patch is to always source virtio's
Kconfig in drivers/Kconfig, and remove it from the appropriate arch
Kconfigs. Additionally, a virtio menu entry has been added so virtio
drivers don't show up in the general drivers menu.

This way anyone can use virtio, though it's arguably less accessible
(and neat!) for virtualization users now.

Note: some architectures (mips and sh) seem to have a VIRTUALIZATION
menu merely for sourcing virtio's Kconfig, so that menu is removed too.
Signed-off-by: NOhad Ben-Cohen <ohad@wizery.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

The pcm driver name has been changed, but the device name has not.
Signed-off-by: NScott Jiang <scott.jiang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>