Since change_bit() requires a (unsigned int *) as second arg,
the correct definition of err_idx[] array declared as
local variable of fsmc_correct_data() is the following:

	u32 err_idx[8];
Signed-off-by: NArmando Visconti <armando.visconti@st.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are
platform specific and were wrongly put in driver specific fsmc.h file.
Move such defines to their respective platform.

Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly
from individual platform.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

ECC1 & ECC4 layout for NAND of different pages sizes for e.g. 512bytes,
2KiB, 4KiB and 8KiB are separated. Previously there existed one ECC4
layout for 2KiB & 4KiB page size due to which oob test module available
in drivers/mtd/nand/test was failing.
Signed-off-by: NBhavna Yadav <bhavna.yadav@st.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

A newly erased page contains ff in data as well as spare area. While reading an
erased page, the read out ecc from spare area does not match the ecc generated
by fsmc ecc hardware accelerator. This is because ecc of data ff ff is not ff
ff. This leads to errors when file system erases and reads back the pages to
ensure consistency.

This patch adds a software workaround to ensure that the ecc check is not
performed for erased pages. This problem is solved by checking the number of
bits (in 512 byte data + 13 byte ecc) which are 0. If these number of bits are
less than 8, the page is considered erased and correction algorithm is not tried
on that page
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch reverts a change that may have been mistakenly included with the set
of patches that introduced the new mtd api entry functions.  Or perhaps I am
mistaken :)

The problem is in the partition wrapper functions, where the calls to the driver
methods were replaced with calls to the new mtd api functions.  This causes the
api function to be called a second time, further down the call stack.  This is
not only unnecessary and redundant - because the sanity checking code and (more
restrictive) bounds checks for the partition were done in the first call - but
is potentially problematic and confusing.

For example, the call stack for a call to mtd_read() on a partitioned device
currently looks like this:

mtd_read()             gets struct mtd_info for the partition
|
+-> part_read()        via the pointer assigned when the partition was created
    |
    +->mtd_read()      this time gets struct mtd_info for the master
       |
       +->xyz_driver_read()  via the pointer asigned by the driver

It seems that this can cause a variety of problems.  For example, if you want to
add code to the api function that tests a value in mtd_info that is relevant
only to the partition.  Or (in my case) you want the driver to return a value
that may be different from that returned by the mtd api function.

This patch eliminates the second call to the mtd api function.  It was tested on
the docg4 nand driver with a subset of the api functions, but I inspected the
rest and don't see any problems.
Signed-off-by: NMike Dunn <mikedunn@newsguy.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Change the name of the mtd so that it is simpler, and is easier to
cope with by mtdparts.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add board and clock setup code for the SH Mobile flctl controller.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add a register used in new FLCTL hardware and a feature flag for it.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Implements the command to seek and read in pages.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The nand base code wants to read out 8 bytes in the READID command.
Reflect this in the driver code.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Reorders the calls to make it a bit shorter and match the calling
procedure displayed in the datasheet.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add support for a new hardware generation. The meaning of some bits
of the FLCMNCR register changed, so some new defines are added
parallel to the existing ones to keep backward compatibility.

The defines allow to choose an appropriate clocking scheme.
Signed-off-by: NBastian Hecht <hechtb@gmail.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use pr_<level> to prefix KBUILD_MODNAME via pr_fmt.

Remove obfuscating defines and use constants in pr_<level>
No need for a do {} while (0) for single statements.

Form of JFFS_<LEVEL> output changes from
"JFFS2 notice: " to "jffs2: notice: "

Added pr_fmt to xattr.c
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use pr_fmt to prefix KBUILD_MODNAME to appropriate logging messages.

Remove now unnecessary internal prefixes from formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Use the more current logging style.

Coalesce formats, align arguments.
Convert uses of embedded function names to %s, __func__.

A couple of long line checkpatch errors I don't care about exist.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

D1 and D2 macros are mostly uses to emit debugging messages.

Convert the logging uses of D1 & D2 to jffs2_dbg(level, fmt, ...)
to be a bit more consistent style with the rest of the kernel.

All jffs2_dbg output is now at KERN_DEBUG where some of
the previous uses were emitted at various KERN_<LEVEL>s.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Since commit ca97dec2 the
command line parsing of MTD partitions does not work anymore.
Signed-off-by: NDaniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Acked-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some strange nand chip(such as Hynix H27UBG8T2A) can pass the `ONFI` signature
check. So the log can be printed out even it is not an ONFI nand indeed.

Change this log to the end of the function. Print out the log only when we
really detect an ONFI nand.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NFlorian Fainelli <ffainelli@freebox.fr>
Acked-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

[1] Background :
    The GPMI does ECC read page operation with a DMA chain consist of three DMA
    Command Structures. The middle one of the chain is used to enable the BCH,
    and read out the NAND page.

    The WAIT4END(wait for command end) is a comunication signal between
    the GPMI and MXS-DMA.

[2] The current DMA code sets the WAIT4END bit at the last one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                                                          ^
                                                          |
                                                          |
                                                     set WAIT4END here

    This chain works fine in the mx23/mx28.

[3] But in the new GPMI version (used in MX50/MX60), the WAIT4END bit should
    be set not only at the last DMA Command Structure,
    but also at the middle one, such as:

    +-----+               +-----+                      +-----+
    | cmd | ------------> | cmd | ------------------>  | cmd |
    +-----+               +-----+                      +-----+
                             ^                            ^
                             |                            |
                             |                            |
                        set WAIT4END here too        set WAIT4END here

    If we do not set WAIT4END, the BCH maybe stalls in "ECC reading page" state.
    In the next ECC write page operation, a DMA-timeout occurs.
    This has been catched in the MX6Q board.

[4] In order to fix the bug, rewrite the last parameter of mxs_dma_prep_slave_sg(),
    and use the dma_ctrl_flags:
    ---------------------------------------------------------
      DMA_PREP_INTERRUPT : append a new DMA Command Structrue.
      DMA_CTRL_ACK       : set the WAIT4END bit for this DMA Command Structure.
    ---------------------------------------------------------

[5] changes to the relative drivers:
    <1> For mxs-mmc driver, just use the new flags, do not change any logic.
    <2> For gpmi-nand driver, and use the new flags to set the DMA
        chain, especially for ecc read page.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Move the header to a more common place.
The mxs dma engine is not only used in mx23/mx28, but also used
in mx50/mx6q.  It will also be used in the future chips.

Rename it to mxs-dma.h, and create a new folder include/linux/fsl/ to
store the Freescale's header files.

change mxs-dma driver, mxs-mmc driver, gpmi-nand driver, mxs-saif driver
to the new header file.
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Acked-by: NVinod Koul <vinod.koul@linux.intel.com>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NNikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

While debugging on SA11x0, the following message was observed:

"Flash device refused suspend due to active operation (state 20)"
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The gpmi driver selects the MTD_CMDLINE_PARTS directly.
But we should not select a visible symbol.

Just remove the select.
Signed-off-by: NHuang Shijie <b32955@freescale.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

As of bb0eb217, MTD_FAIL_ADDR_UNKNOWN should be used to indicate mtd
erase failure not specific to any particular block.

Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff when setting
'erase->fail_addr' in 'efx_mtd_erase()'.
Signed-off-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Correct spelling "modul" to "module" in
fs/hffs2/compr.c
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In commit "c7975330 mtd: abstract last MTD partition parser argument" the
third argument of "mtd_device_parse_register()" changed from start address
of the MTD device to a pointer to a struct.

The "ixp4xx_flash_probe()" function was not converted properly, causing
an oops during boot.

This patch fixes the problem by filling the needed information into a
"struct mtd_part_parser_data" and passing it to
"mtd_device_parse_register()".
Signed-off-by: NMarc Kleine-Budde <mkl@blackshift.org>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.

This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

In many places in drivers we verify for the zero length, but this is very
inconsistent across drivers. This is obviously the right thing to do, though.
This patch moves the check to the MTD API functions instead and removes a lot
of duplication.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Reviewed-by: NShmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Some MTD drivers return -EINVAL if the 'phys' parameter is not NULL, trying to
convey that they cannot return the physical address. However, this is not very
logical because they still can return the virtual address ('virt'). But some
drivers (lpddr) just ignore the 'phys' parameter instead, which is a more
logical thing to do.

Let's harmonize this and:

1. Always initialize 'virt' and 'phys' to 'NULL' in 'mtd_point()'.
2. Do not return an error if the physical address cannot be found.

So as a result, all drivers will set 'phys' to 'NULL' if it is not supported.
None of the 'mtd_point()' users use 'phys' anyway, so this should not break
anything. I guess we could also just delete this parameter later.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The MTD API function now zero the 'retlen' parameter before calling
the driver's method — do not do this again in drivers. This removes
duplicated '*retlen = 0' assignent from the following methods:

    'mtd_point()'
    'mtd_read()'
    'mtd_write()'
    'mtd_writev()'
    'mtd_panic_write()'
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.

And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We already verify that offset and length are within the MTD device size
in the MTD API functions. Let's remove the duplicated checks in drivers.
This patch only affects the following API's:

'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'

This patch adds a bit of noise by removing too sparse empty lines, but this is
not too bad.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.

The modified API functions are:

'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'

This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.

Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:

 * bootloader cannot read the flash-based BBT format
 * BBT is corrupted and the flash must be rescanned for bad
   blocks; we want to remember bad blocks that were marked from Linux

So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.

The new flash-based BBT procedure for marking bad blocks:
 (1) erase the affected block, to allow OOB marker to be written cleanly
 (2) update in-memory BBT
 (3) write bad block marker to OOB area of affected block
 (4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.

This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.

Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

We do not need to invoke 'mtd_can_have_bb()' before invoking
'mtd_block_isbad()' because the latter already handles the case when the MTD
device does not support bad blocks.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>