This ports the iwlwifi rfkill code to the new API offered by
cfg80211 and thus removes a lot of useless stuff. The soft-
rfkill is completely removed since that is now handled by
setting the interfaces down.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no need to check if a pointer is NULL before calling
vfree(), since vfree() function already check for it.
Signed-off-by: NBreno Leitão <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Include offloaded FCoE data into total rx/tx statistics for 82599 so they
are properly reflected by ethtool or ifconfig.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethtool is a standard way of getting information about
ethernet interfaces.  We enhance ethtool kernel interface
& e1000e to make the MDI-X status readable via ethtool in
userspace.
Signed-off-by: NChaitanya Lala <clala@riverbed.com>
Signed-off-by: NArthur Jones <ajones@riverbed.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

e1000e_config_collision_dist() sets tctl, but subsequently tctl is
overwritten.  It seems to me that as things stand the call to
e1000e_config_collision_dist() has no effect and should either be
removed or moved down a little bit.  This kernel patch takes the latter
option.
Signed-off-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Phy corruption has been observed on 2-port 82571 adapters, and is root-caused
to lack of synchronization between the 2 driver instances, which conflict
when attempting to access the phy via the single MDIC register.
A semaphore exists for this purpose, and is now used on these designs. Because
PXE &/or EFI boot code (which we cannot expect to be built with this fix) may
leave the inter-instance semaphore in an invalid initial state when the driver
first loads, this fix also includes a one-time (per driver load) fix-up of the
semaphore initial state.
Signed-off-by: Ndave graham <david.graham@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fakehard is a really simple driver implementing only necessary
callbacks and serves the role of an example of driver for HardMAC
IEEE 802.15.4 device.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver does not indicate support for frag lists.

Furthermore, even if it did, the code is walking the frag
lists incorrectly.  The idiom is:

	for (iter = skb_shinfo(skb)->frag_list; iter; iter = iter->next)

but it's doing:

	for (iter = skb_shinfo(skb)->frag_list; iter;
	     iter = skb_shinfo(iter)->frag_list)

which would never work.  And this proves that this driver never
saw an SKB with active frag lists.

So just remove the code altogether and the driver TX path becomes
much simpler.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A driver overhaul on 29 Feb 2000 (!) broke locking around fiddling with 
the tx descriptor ring in start_xmit(); a follow-on "fix" removed the 
broken remnants altogether.  Here's a patch to restore proper locking in 
the function -- the complement in the interrupt handler has been correct 
all the time.

 This *may* have been the reason for the occasional confusion of the chip 
-- triggering a tx timeout followed by a chip reset sequence -- seen on 
R4k-based DECstations with the onboard Ethernet interface.  Another theory 
is the confusion is due to an unindentified problem -- perhaps a silicon 
erratum -- associated with the variation of the MT ASIC used to interface 
the R4k CPU to the rest of the system on these computers; with its 
aggressive write-back buffering the design is particularly weakly ordered 
when it comes to MMIO (in the absence of ordering barriers uncached reads 
are allowed to bypass earlier uncached writes, even if to the same 
location), which may trigger all kinds of corner cases in peripheral 
hardware as well as software.

Either way this piece of code is buggy.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible for tun_chr_close to race with dellink on the
a tun device.  In which case if __tun_get runs before dellink
but dellink runs before tun_chr_close calls unregister_netdevice
we will attempt to unregister the netdevice after it is already
gone.  

The two cases are already serialized on the rtnl_lock, so I have
gone for the cheap simple fix of moving rtnl_lock to cover __tun_get
in tun_chr_close.  Eliminating the possibility of the tun device
being unregistered between __tun_get and unregister_netdevice in
tun_chr_close.
Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com>
Tested-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state)) was being hit
during e100 EEH recovery. The problem source was a napi_enable
call being made during e100_io_error_detected. Napi should remain
disabled after e100_down, and only be reenabled when the interface
is recovered.

This patch also updates e100_io_error_detected in order to make
it similar to the current versions of the error_detected callback
in drivers such as e1000e and ixgbe.
Signed-off-by: NAndre Detsch <adetsch@br.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If mlx4_create_eq() would fail for one of EQ's assigned for
completion handling, the code would try to free the same EQ
we failed to create.
The crash was found by Christoph Lameter
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the right structure while incrementing the offset in tun_get_user.
Signed-off-by: NSridhar Samudrala <sri@us.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.

One to access nr_frags, one to access dma_maps[0]

Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.

Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the private definition of TRUE/FALSE and use the ones from
linux/stddef.h. Also remove the definition of BOOL which is not referenced
inside the driver anyway.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a driver for the Micrel KS8842 ethernet switch.

The supplied code is for driving the KS8842 through the Timberdale FPGA
on the Russellville board, a development board for Intel Atom CPU
in the automotive area.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As all current versions of virtio_net generate a value for the
header length that's too small, we should optimise this so that
we don't copy it twice.  This can be done by ensuring that it is
at least as large as the place where we'll write the checksum.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Through a bug in the tun driver, I noticed that virtio_net is
producing bogus hdr_len values.  In particular, it only includes
the IP header in the linear area, and excludes the entire TCP
header.  This causes the TCP header to be copied twice for each
packet.  (The bug omitted the second copy :)

This patch corrects this.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes an initialization error; the chip negotiates gigabit, but
the driver mistakenly handled it as 100Mb.
Changes based on both SiS own GPL driver and forcedeth.
Hopefully should fix
	http://bugzilla.kernel.org/show_bug.cgi?id=9735
	http://bugzilla.kernel.org/show_bug.cgi?id=11149Signed-off-by: NRiccardo Ghetta <birrachiara@tin.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRiccardo Ghetta <birrachiara@tin.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRiccardo Ghetta <birrachiara@tin.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Corrected dma sync handling on small packets. Should fix
http://bugzilla.kernel.org/show_bug.cgi?id=11509
Note:
While this bug was reported only on x86_64, it could have affected
any architecture.
Signed-off-by: NRiccardo Ghetta <birrachiara@tin.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some firmware mailbox commands require the firmware to
communicate with the FCoE driver running on another
PCI function.  This can potentially take several seconds.
This wait is done in process context only.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 8 banks of 'sub-registers' each of which are accessed
through address/data register pair.  An example would be reading
flash or the xgmac.  Accessing these require the driver to wait for
a ready bit before writing the address and then accessing the data.
This patch increases the timeout to 100us to prevent timeouts
that have been seen on some platforms.
These register are accessed in process context only.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since an FCoE function shares a port with this NIC function, the
jumbo settings must always be in place.  This patch causes the
hardware to be set up for jumbo if it is not already done.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each firmware mailbox command can have a different number of
valid data elements. When waiting for a mailbox command to
complete it the process passes it's element count and
waits for the completion.  It is possible that while waiting
an unrelated firmware async event (AE) can arrive.  When this
happens, the handler will over write the element count
with the value for the newly arrived AE. This can cause
the mailbox command to not get all of it's data.
This patch restores original mailbox count at the end
of the handler.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check status on every iteration of event handler loop and exit
if an error occurred.  If an error occurred then recover process
will be queued so this loop should no continue.
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc911x_drv_remove() function is declared with __devexit, so the
assignment to the driver structure needs __devexit_p() wrappings to prevent
build failure when hotplug is disabled.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsc911x driver works fine on Blackfin systems, so add it to the arch
list in the Kconfig.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With all the last patchsets going in for 82599 feature enablement, the
driver version needs to be increased for better identification.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

82599 has a FW running that helps manage the internal SFI PHY.  There are
also a number of pre-production samples of these SFI-based devices in the
field.  This patch adds a check to look for the firmware running on all
SFP+ based adapters, and displays a warning to the system log if a
pre-production adapter is identified.  The driver will continue loading
though, with no functional degradation.

Also remove an old function prototype from ixgbe_82599.c that isn't being
used.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch rearranges the ixgbe_ring struct to make better use of
cacheline efficiency.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables Flow Director's ATR functionality to the main base
driver for 82599.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the functions for ixgbe to initialize Flow Director.  It
also has the function APIs to add Flow Director filters from the base
driver.  This also includes ATR, Application Targeted Routing, which is a
feature set of Flow Director.  This is the hash-based mechanism to
automatically identify flows and add filters based on the hash, and direct
the Rx of that flow back to that same CPU.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow Director is a Rx filter mechanism designed to match Rx flows back to
the same CPU that the flow's Tx occurred from.  This patch adds the first
piece, the defines for the hardware registers, to enable this feature in
82599 hardware.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a second feature flag variable to use for future feature
expansion.  Add HW RSC to this new feature flags variable.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the tx cleanup processing out of the MSI-X interrupt
processing and gives it it's own napi routine.  This allows the driver to
process TX cleanup in a polling context instead of in an interrupt context
which prevents TX from starving RX.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The v_idx value was being used as both a bitmask and an index.  This change
makes it so that the q_vector contains the index and allows for much of the
code to be simplified since disabling a q_vector involves only clearing one
bit in the interrupt bitmask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the driver so that it uses rx_buffer_info->dma to
determine if it needs to unmap the page instead of sh_info->nr_frags.  This
helps to prevent a cache line miss when receiving small packets as the
rx_buffer_info data should already be in the cache.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>