For STA mode, collect VHT realated IEs from the Beacons or Probe
Responses and append similar VHT related IEs to association
requests.

For AP mode, get VHT related capability information and share it
with cfg80211 at the time of wiphy register. This information is
further used by cfg80211 and hostapd to start an AP with 802.11AC
support.

Currently only 8897 supports 802.11AC.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

They all can make one line.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While unloading driver, we free all pending TX packets by flushing
TX ring. There is unhandled case for PCIE8897 while checking for
ring empty condition.

This patch adds the handling by calling mwifiex_pcie_txbd_empty().
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I removed a bit too much info last time.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Theoretically, the card may not enter CTKILL:
In case the timer that iwl_prepare_ct_kill_task is setting,
will expire before tt->state revert to its previous state.
Signed-off-by: NEytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The time event data structures are required also for P2P Device
interface.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Occasionally, we would run into this warning:

  iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left
  iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601
  iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9
  iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9
  iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601
  iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD
  iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1
  wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3)
  ------------[ cut here ]------------
  WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]()
  Modules linked in: [...]
  Call Trace:
   [<c1046e42>] warn_slowpath_common+0x72/0xa0
   [<c1046e92>] warn_slowpath_null+0x22/0x30
   [<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]
   [<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm]
   [<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm]
   [<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211]

The reason is a problem with asynchronous vs. synchronous
commands, what happens here is the following:
 * TE 0x2601 is removed, the TIME_EVENT_CMD for that is async
 * a new TE (will be 0x2701) is created, the TIME_EVENT_CMD
   for that is sync and also uses a notification wait for the
   response (to avoid another race condition)
 * the response for the TE 0x2601 removal comes from the
   firmware, and is handled by the notification wait handler
   that's really waiting for the second response, but can't
   tell the difference, we therefore see the message
   "TIME_EVENT_CMD response - UID = 0x2601" instead of
   "TIME_EVENT_CMD response - UID = 0x2701".

Fix this issue by making the TE removal synchronous as well,
this means that we wait for the response to that command
first, before there's any chance of sending a new one.

Also, to detect such issues more easily in the future, add
a warning to the notification handler that detects them.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This is helpful for debugging the time event warning,
but also in general to see what's going on.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

All station commands must include a valid MAC ID,
the ID 0 is randomly valid in some cases, but we
must set the ID properly. Do that by passing the
right station and using its mac_id_n_color.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For the firmware to know when DTIM beacons arrive
we have to program the DTIM time in TSF and system
time in the MAC context. Since mac80211 now tracks
the different times (on demand), this becomes easy.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
while the mac80211-next tree removed
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Larry noticed (and bisected) that commit df881293
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.

Cc: Jouni Malinen <j@w1.fi>
Bisected-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If mesh plink debugging is enabled, this gets annoying in
a crowded environment, fast.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert mesh peering events into strings and make the
debug output a little easier to read. Also stop printing
the llid and plid since these don't change across peering
states and are random numbers anyway so they just amount
to noise.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ieee80211_ht_cap_ie_to_sta_ht_cap() will clean up the
ht_supported flag and station bandwidth field for us
if the peer beacon doesn't have an HT capability element
(is operating as non-HT).

Also, we don't really need a special station ch_width
member to track the station operating mode any more so use
sta.bandwidth instead.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If an interface is set down while authenticating or
associating, there's a station entry that will be
removed by the flushing in do_stop() and that will
cause a warning. It's otherwise harmless, but avoid
the warning by calling ieee80211_mgd_stop() first.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Update the 802.11 book to list the correct
data structures.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since mesh powersaving was added, pending bcast/mcast frames may go out the
CAB queue now.  Unfortunately, the queue was only set up for AP mode, so we
would try to tx on the IEEE80211_INVAL_HW_QUEUE.  Allow cab_queue for mesh
interfaces as well.

Fixes the following warning (or crash without MAC80211_VERBOSE_DEBUG):

WARNING: at net/mac80211/tx.c:1223 __ieee80211_tx+0x162/0x35f [mac80211]()
Modules linked in: mac80211_hwsim mac80211 cfg80211 [...]
Pid: 3085, comm: avahi-daemon Tainted: G        W    3.8.0-rc1+ #377
Call Trace:
 [<ffffffff81045c20>] warn_slowpath_common+0x83/0x9c
 [<ffffffff81045c53>] warn_slowpath_null+0x1a/0x1c
 [<ffffffffa083aef0>] __ieee80211_tx+0x162/0x35f [mac80211]
 [<ffffffffa083cb1d>] ieee80211_tx+0xd3/0xf9 [mac80211]
 [<ffffffffa083cc0f>] ieee80211_xmit+0xcc/0xd5 [mac80211]
 [<ffffffffa083db59>] ieee80211_subif_start_xmit+0xc53/0xcd8 [mac80211]
 [<ffffffff81319acd>] dev_hard_start_xmit+0x259/0x3ce
 [<ffffffff81333d6b>] sch_direct_xmit+0x74/0x17d
 [<ffffffff8131a0b1>] dev_queue_xmit+0x230/0x414
 [<ffffffff8134877a>] ip_finish_output2+0x348/0x3aa
 [<ffffffff81349029>] ip_finish_output+0x6c/0x71
 [<ffffffff81349046>] NF_HOOK_COND.constprop.44+0x18/0x58
 [<ffffffff8134a03a>] ip_mc_output+0x134/0x13c
 [<ffffffff8134835a>] dst_output+0x18/0x1c
 [<ffffffff81349a24>] ip_local_out+0x20/0x24
 [<ffffffff8134a8cf>] ip_send_skb+0x16/0x3c
 [<ffffffff8136bfba>] udp_send_skb+0x254/0x2b9
 [<ffffffff8136c85e>] udp_sendmsg+0x5a8/0x7d4
Signed-off-by: NBob Copeland <bob@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's various code with strange indentation,
questionable loop and locking constructs, etc.

The bigger change is moving the "sdata" argument
to the first argument of all functions, like all
other mac80211 functions that have one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Otherwise memory corruption occurs when using channel contexts (ATM when
param 'channel' > 1).
Signed-off-by: NKarl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Even when connecting to an AP that doesn't support VHT,
and even when the local device doesn't support it either,
the downgrade message gets printed. Suppress the message
if HT and/or VHT is disabled.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding the flag to mac80211 already without testing was
clearly a mistake, one that we now pay for by having to
reserve bit 13 forever. The problem is cfg80211 doesn't
allow capability/rate changes for station entries that
were added unassociated, so the station entries cannot
be set up properly when marked associated.

Change the NL80211_FEATURE_FULL_AP_CLIENT_STATE value
to make it clear to userspace implementations that all
current kernels don't actually support it, even though
the previous bit is set, and of course also remove the
flag from mac80211 until we test and fix the issues.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.

In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The information of the peer's capabilities and extended capabilities are
required for the driver to perform TDLS Peer UAPSD operations and off
channel operations. This information of the peer is passed from user space
using NL80211_CMD_SET_STATION command. This commit enhances
the function nl80211_set_station to pass the capability information of
the peer to the driver.

Similarly, there may be need for capability information for other modes,
so allow this to be provided with both add_station and change_station.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use the new extended capabilities advertising to advertise
the fact that operating mode notification is supported.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In many cases, userspace may need to know which of the
802.11 extended capabilities ("Extended Capabilities
element") are implemented in the driver or device, to
include them e.g. in beacons, assoc request/response
or other frames. Add a new nl80211 attribute to hold
the extended capabilities bitmap for this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mesh interfaces will now respond to any broadcast (or
matching directed mesh) probe requests with a probe
response.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Previously, the entire mesh beacon would be generated each
time the beacon timer fired. Instead generate a beacon
head and tail (so the TIM can easily be inserted when mesh
power save is on) when starting a mesh or the MBSS
parameters change.

Also add a mutex for protecting beacon updates and
preventing leaks.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make all the parsed IE pointers const, and propagate
the change to all the users etc.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When drivers or regulatory have limitations on
40, 80 or 160 MHz channels, advertise these to
userspace via nl80211. Also add a new feature
flag to let userspace know this is supported.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers might support 80 or 160 MHz only on some
channels for whatever reason, so allow them to disable
these channel widths. Also maintain the new flags when
regulatory bandwidth limitations would disable these
wide channels.
Reviewed-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A while ago, I made the mac80211 station code never change
the channel type after association. This solved a number of
issues but is ultimately wrong, we should react if the AP
changes the HT operation IE and switches bandwidth. One of
the issues is that we associate as HT40 capable, but if the
AP ever switches to 40 MHz we won't be able to receive such
frames because we never set our channel to 40 MHz.

This addresses this and VHT operation changes. If there's a
change that is incompatible with our setup, e.g. if the AP
decides to change the channel entirely (and for some reason
we still hear the beacon) we'll just disconnect.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>