The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
768x1024 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
(both volume buttons are also connected to the UBOOT_SEL pin). The
external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
OTG and 3.5mm headphone jack.

USB OTG is enabled in host only mode. AXP221 USB power supply and
GPIO support are required for full USB OTG support.
Signed-off-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: NKarsten Merker <merker@debian.org>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.

It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.

It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Sinlinx A31s SDK is a A31s based module/baseboard development kit.

The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.

The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>

The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: NSiarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.

Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.
Signed-off-by: NJelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port

This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: NLawrence Yu <lyu@micile.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This commits adds a generic dts file for q8 formfactor a13 based tablets.

The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.

The wifi is USB based, and thus not listed in devicetree.

The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.

This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.

This commit adds a dts file adding support for this top set box.
Signed-off-by: NJelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.

This patch has been tested on both rev2 and rev5 of this board / these
tablets.

It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.

These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.

Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.

This commit adds a dts for v4 of the gt90h pcb.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Commit 79ae3e66 (ARM: dts: sun4i: Add Iteaduino Plus A10) added a new
make target for the sun4i-a10-itead-iteaduino-plus dts file, but mistakenly
used .dts instead of the correct .dtb suffix.  This resulted in a build error
like:

        scripts/Makefile.dtbinst:42: target 'sun4i-a10-itead-iteaduino-plus.dts' doesn't match the target pattern

when doing a make dtbs_install.

Fix it to use the proper file name.
Signed-off-by: NJosh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This change is a code reorganization. Here we introduce
serial_imx_enable_wakeup() helper function to do
the job of configuring and preparing wakeup sources
on imx serial device. The idea is to allow other
parts of the code to call this function whenever
the device is known to go to idle.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new SOC i.MX6UL dtb file support, including evk board
support

i.MX6 Ultralite processor include one ARM cortext-A7 core.
Offer high perfomance and lowest power consumption.

Main included:
- 4 MMC/SD/SDIO
- 2 USB 2.0 OTG
- 3 I2S/SAI/AC97
- 4 eCSPI
- 4 I2C
- 2 ENET
- 2 CAN
- 3 wdog
- ASRC
- 8 uart
- LCDIF
- PXP
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NFugang Duan <B38611@freescale.com>
Signed-off-by: NFancy Fang <chen.fang@freescale.com>
Signed-off-by: NFrank Li <Frank.Li@freescale.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Initial version of DTSI for ProXstream2 and PH1-LD6b and DTS for
PH1-LD6b reference board.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
[olof: sort Makefile entries]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Turns out I fumbled a couple of the merge resolutions for marzen board removal.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Also known as the Asus Chromebook Flip.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>

The title says it all. The name of the dts file as been changed to
better reflect the manufacturer's device name (LS-WSGL), rather than
the original "lsmini", which exists in a kirkwood version too.

[gregory.clement@free-electrons.com]: use tab instead of space to
indent dts at line 185. Reslove merge conflict with patch "ARM: dts:
orion5x: add buffalo linkstation ls-wtgl" in the file
arch/arm/boot/dts/Makefile.
Signed-off-by: NBenjamin Cama <benoar@dolka.fr>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAlexey Kopytko <alexey@kopytko.ru>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Devkit8000 was sold with a 4.3" LCD or 7.0" or without. This patch
creates one dts file per bundle.
Signed-off-by: NAnthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>

Add the initial device  tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.

Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Remove Marzen legacy board code written in C. Instead
board support expressed in DT shall be used together
with Multiplatform and shmobile_defconfig.
Signed-off-by: NMagnus Damm <damm+renesas@opensource.se>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add dts file to support Buffalo Linkstation LS-WTGL,
which is marvell orion5x based 2-bay 3.5" HDD NAS.
Product info:
 - (JPN) http://buffalo.jp/products/catalog/storage/ls-wtgl_r1/
 - (ENG) http://www.buffalotech.com/support-and-downloads/download/LinkStation_Pro_Duo_Manual_web.pdfSigned-off-by: NRoger Shimizu <rogershimizu@gmail.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>

Add minimal support for HP T410.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add minimal dts support for dm8148-evm.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Which is formally known as the Asus C201 chromebook
Signed-off-by: NRomain Perier <romain.perier@gmail.com>
Reviewed-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

Main features of STM32429i-EVAL evaluation kit are:
 - STM32F429 Cortex-M4 MCU @180MHz
   * 2MB internal Flash
   * 256KB internal RAM
 - 32MB SDRAM
 - 16MB NOR Flash
 - 2MB SRAM
 - 4.3" TFT LCD with resistive touchscreen
 - SDCard connector (SDIO compatible)
 - 1x USB 2.0 OTG + 1x USB 1.1 OTG
 - Ethernet
Signed-off-by: NMaxime Coquelin <mcoquelin.stm32@gmail.com>

The Terasic DE0 Atlas board is also known as the DE0-Nano board.
This patch adds the DTS board file for the DE0-Nano Sockit board, and not
the DE0 Nano "Development Board".
Signed-off-by: NDalon Westergreen <dwesterg@gmail.com>
Signed-off-by: NDinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Updated skew settings for the gmac1 node as this board is using the
    KSZ9031 PHY instead of the 9021 PHY.
v2: use stdpath-out for console and remove comment regarding u-boot ethaddr

Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.
Signed-off-by: NJosef Gajdusek <atx@atx.name>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.

Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.

WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot
Signed-off-by: NTeresa Remmet <t.remmet@phytec.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This adds basic chip support for Mediatek 6580.
Signed-off-by: NMars Cheng <mars.cheng@mediatek.com>
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>

While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>

The Hisense Chromebook C11, also named jerry.
Signed-off-by: NAlexandru M Stan <amstan@chromium.org>
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NDoug Anderson <dianders@chromium.org>