[Why]
Previously SMU was giving us 0s for the clock table. Now they have valid
clock table. We should use theirs. Also, need to send SMU watermark
ranges for selecting optimal watermarks.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Without a check for virtual links, every link's DIG was getting
checked for enabled or disabled. If link was virtual, since it
did not have a DIG, this would cause issues.

[HOW]
Skip DIG Enable check if link is virtual and add virtual link to
to display count.
Signed-off-by: NSung Lee <sung.lee@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
HDMI 2.0 requires scrambling under specific conditions. We refer to
stream property LTE_340MCSC_SCRAMBLE to determine whether en/dis
scrambling.
While creating stream for sink, we setup LTE_340MCSC_SCRAMBLE by
referring to edid_caps. However, dm_helpers_parse_edid_caps()
doesn't construct HDMI Forum block data for edid_caps.
Moreover, fill_stream_properties_from_drm_display_mode() aslo
unconsciously clear the LTE_340MCSC_SCRAMBLE flag.

[How]
Drm already provides drm_display_info to refer HDMI Forum vsdb info.
Set stream LTE_340MCSC_SCRAMBLE by drm_display_info and remove
memset in fill_stream_properties_from_drm_display_mode()
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]

During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.

During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.

[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: NDavid Galiffi <david.galiffi@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Static ramp to max refresh rate does not have capability check on
calculated v_total. Programming a lower v_total_min and max than the
total causes continuous spurious HPDs.

[How]
Add a capability check after v_total calculation similar to calculate
v_total helper functions.
Signed-off-by: NJaehyun Chung <jaehyun.chung@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
1. defer delay and sw start delay has been mixed up, defer delay was
programmed to AUX_SW_CONTROL:AUX_SW_START_DELAY.
2. There's no delay for defer

[how]
1. Set  aux sw start to 0
2. Add delay for defer scenario
Signed-off-by: NXiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Description]
use vbios message to call smu for dpm level
also only program dmdata in vsyncflip as HW requirement.
Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]

Compiling with GCC 9.1.0 gives the following warning (I have
warnings-as-errors enabled):

drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c: In function 'dc_validate_seamless_boot_timing':
drivers/gpu/drm/amd/amdgpu/../dal-dev/dc/core/dc.c:1180:8: error: 'se' may be used uninitialized in this function [-Werror=maybe-uninitialized]
 1180 |   if (!se->funcs->dp_get_pixel_format(
      |        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 1181 |    se,
      |    ~~~
 1182 |    &hw_crtc_timing.pixel_encoding,
      |    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 1183 |    &hw_crtc_timing.display_color_depth))

[How]

Initialize se to NULL.
Signed-off-by: NLeo Li <sunpeng.li@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
we found using an active DP to HDMI panel that we weren't validating
dp_pixel_format and hardware timing v_front_porch, causing screen to
blank and/or corrupt while attempting a seamless boot.

[how]
added checks during dc_validate_seamless_boot_timing for these values
Signed-off-by: NMartin Leung <martin.leung@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why & How]
Dongle 0x00E04C power down all internal circuits including
AUX communication preventing reading DPCD table.
Encoder will skip DP RX power down on disable output
to keep receiver powered all the time.
Signed-off-by: NVitaly Prosyak <vitaly.prosyak@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: NVitaly Prosyak <Vitaly.Prosyak@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
Number of audio endpoints wasn't updated from dcn20's 6 when created

[HOW]
Changed num_audio to 4 to match the correct sbios value
Signed-off-by: NMichael Strauss <michael.strauss@amd.com>
Reviewed-by: NYongqiang Sun <yongqiang.sun@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
dp_48m_refclk_driver_pwdn is persistent through S3 and S5.
This was worked arround in SMU FW 55.21.0. Earlier FW don't have this fix
so we will hang on reboot

[how]
add a guard for smu versions before SMU FW 55.21.0
Signed-off-by: NJoseph Gravenor <joseph.gravenor@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The SMU message to enable this feature looks at argument. Previous code
didn't send right argument. This change will allow the feature to be
be enabled.

[How]
Fixed one issue where SMU message to enable the feature was sent without
setting the parameter.
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
If 48mhz refclk is turned off during PSR, we will have issue doing
link training during detection.

[How]
Get out of PSR before detection
Signed-off-by: NEric Yang <Eric.Yang2@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When diags adds a DWB via a stream update, we calculate MMHUBBUB
paramaters, but dc->current_state has not yet been updated
when the DWB programming happens. This leads to overflow on
high bandwidth tests since the incorrect MMHUBBUB arbitration
parameters are programmed.

[How]
Pass the updated context down to the (enable|update)_writeback functions
so that they can use the correct watermarks when programming MMHUBBUB.
Signed-off-by: NJulian Parkin <julian.parkin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[WHY]
dpp2_get_optimal_number_of_taps is incorrect, and dcn2 should be using
dpp1_get_optimal_number_of_taps instead
Signed-off-by: NWesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There is a bug when determining if link training should be retried when
HPD is low in dp_verify_link_cap_with_retries.

[How]
Correctly, fail dp_verify_link_cap_with_retries without retry when
HPD is low.
Signed-off-by: NSivapiriyan Kumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NAbdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When the driver sends a pipe set command to the DMCU FW, it does not wait
for the command to complete. This can lead to unpredictable behavior if,
for example, the driver were to request a pipe disable to the FW via MCP,
then power down some hardware before the firmware has completed processing
the command.

[How]
Wait for the DMCU FW to finish processing set pipe commands
Signed-off-by: NJosip Pavic <Josip.Pavic@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Output bitrate was mistakenly left out, causing corruption on some
DSC low resolution (such as 800x600) modes.
Signed-off-by: NNikola Cornij <nikola.cornij@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Some displays rely on the SPD verticle frequency maximum value.
Must round the calculated refresh rate to the nearest integer.

[How]
Round the nominal calculated refresh rate to the nearest whole
integer.
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
This function was mistakenly reverted as part of a legitimate revert. The
old version that was reverted to has bad logic, and is causing situations
where p-state change support is being toggled when it shouldn't be,
resulting in hangs.
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Type-c PHY config is not align with dpcd lane count.
When those values didn't match, it cause driver do
link training with 4 lane but phy only can output 2 lane.
The link trainig always fail.

[How]
1. Modify get_max_link_cap function. According DPALT_DP4
to update max lane count.
2. Add dp_mst_verify_link_cap to handle MST case because
we didn't call dp_mst_verify_link_cap for MST case.
Signed-off-by: NLewis Huang <Lewis.Huang@amd.com>
Reviewed-by: NWenjing Liu <Wenjing.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Didn't send VSIF infopacket when it's 4k mode defined in HDMI 1.4b.
For HDMI 1.4b, While displaying 4k modes, it should send VSP.

[How]
Call mod_build_hf_vsif_infopacket() function to build info frame
and send it.
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NAnthony Koo <Anthony.Koo@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The register CM_TEST_DEBUG_DATA is used in dpp1_program_input_csc, which is
called from dpp2_cnv_setup, but the shifts and masks for the fields of that
register are not initialized for dcn2. This causes all reads of that register
to return 0.
Signed-off-by: NJoshua Aberback <joshua.aberback@amd.com>
Reviewed-by: NJaehyun Chung <Jaehyun.Chung@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
memcmp is vulnerable to regression due to dc_clocks structures not being
organized properly (not "current" clock related structures being at the beginning
of the structure) and causes unnecessary setting of the optimize bit

[how]
add a dcn sepcific comparator, implement for dcn2
Signed-off-by: NJun Lei <Jun.Lei@amd.com>
Reviewed-by: NAnthony Koo <Anthony.Koo@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
The vendor specific infoframe is needed for HDMI while displaying
specific modes.
DC supports sending it, but we aren't currently building it

[How]
Add mod_build_hf_vsif_infopacket() to build the vendor specific
info packet.
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
HPD is not suppressed when we lower
clocks on renoir. B/c of this we do link
training when the 48mhz refclk is off, which
will cause ASIC hang.

[how]
Exit optimized power state for detection purpose.
Signed-off-by: NJoseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: NEric Yang <eric.yang2@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently pipe split may steal an existing ODM pipe depending on stream
sequence. This change prevents that from happening as easily.
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NGary Kattan <Gary.Kattan@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
When planes are added or removed from a stream, the change
in pipe usage from dynamic MPC combine can cause a second
stream using ODM combine to pick a different pipe to combine with.

In this scenario, a different OPP is connected to the ODM without
programming its FMT.

[How]
Reprogram the FMT in dcn20_program_pipe whenever a pipe is
newly enabled, or when its opp changes.
Signed-off-by: NJulian Parkin <julian.parkin@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
If VSTARTUP changes due to bandwidth requirements, we must
recalculate and update VLINE2 as well for proper flip reporting.

[How]
After all calls to program_global_sync which reconfigures
VSTARTUP, also make sure to update V_UPDATE (i.e. VLINE2 on DCNx).
Signed-off-by: NAric Cyr <aric.cyr@amd.com>
Reviewed-by: NSivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
A recent bug showed that logging would be useful in debugging
various gamma issues.

[How]
Fix formatting for easier graphing.
Prevent performance hit when doing diag.
Signed-off-by: NWyatt Wood <wyatt.wood@amd.com>
Reviewed-by: NAric Cyr <Aric.Cyr@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Virtual signal means there is no display attached.
In this case we will assign a virtual signal type to the stream.
We should only enable the front end of the stream but not the back end.

[how]
When stream is enabling with virtual signal type, skip backend programming.
Signed-off-by: NWenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: NJun Lei <Jun.Lei@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
While displaying 4k modes defined in HDMI1.4b, should set VIC to 0
and use VSP HDMI_VIC to indicate the mode.

[How]
Use functions defined in drm to set up the VIC correspondingly.
Signed-off-by: NWayne Lin <Wayne.Lin@amd.com>
Reviewed-by: NNicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
To compare the crc of the framebuffer data at input of
display pipeline with the crc of the otg, we need to
disable pixel formatter's dynamic expansion feature during
crc capture and keep it enable in the normal operation.

[HOW]
Expose a new interface in DM and dc for pixel formatter
(fmt dynamic bitdepth expansion control). Interface control
the FMT_DYNAMIC_EXP_EN  bit, during crc capture keep
it disabled.
Signed-off-by: NRobin Singh <robin.singh@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This allows gfx cache to be probed and invalidated (for none-dirty cache lines)
on a HDP write (from either another GPU or CPU). This should work only for the
memory mapped as RW memory type newly added for arcturus, to achieve some cache
coherence b/t multiple memory clients.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NChristian Konig <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Many logic in this function are HDP set up,
not gart set up. Moved those logic to gmc_v9_0_hw_init.
No functional change.
Signed-off-by: NOak Zeng <Oak.Zeng@amd.com>
Acked-by: NChristian konig <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Use asic constants.
Signed-off-by: NMarek Olšák <marek.olsak@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>