This change makes certain that any packet we attempt to transmit will meet
minimum size requirements for the hardware.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to just cleanup the logic in ixgbe_change_mtu since we
are making it unnecessarily complex due to a workaround required for 82599
when SR-IOV is enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces the existing Rx hot-path in the ixgbe driver with a new
implementation that is based on performing a double buffered receive.  The
ixgbe driver already had something similar in place for its' packet split
path, however in that case we were still receiving the header for the
packet into the sk_buff.  The big change here is the entire receive path
will receive into pages only, and then pull the header out of the page and
copy it into the sk_buff data.  There are several motivations behind this
approach.

First, this allows us to avoid several cache misses as we were taking a
set of cache misses for allocating the sk_buff and then another set for
receiving data into the sk_buff.  We are able to avoid these misses on
receive now as we allocate the sk_buff when data is available.

Second we are able to see a considerable performance gain when an IOMMU is
enabled because we are no longer unmapping every buffer on receive.
Instead we can delay the unmap until we are unable to use the page, and
instead we can simply call sync_single_range on the half of the page that
contains new data.

Finally we are able to drop a considerable amount of code from the driver
as we no longer have to support 2 different receive modes, packet split and
one buffer.  This allows us to optimize the Rx path further since less
branching is required.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive all frames available, including
those with bad FCS, ethernet control frames, and more.

Tested by sending frames with bad FCS.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Including bad FCS, used generate frames with bad FCS
to test other system's handling of RX of bad packets.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.

Tested by sending frames with bad FCS.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Including bad FCS, used generate frames with bad FCS
to test other system's handling of RX of bad packets.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

- add eni_do_release() to balance eni_do_init
- turn the zeroes DMA area into a per device data
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds clk_prepare/clk_unprepare calls to the pxaficp_ir
driver by using the helper functions clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I found recently that the arp_process function which handles all of our received
arp frames, is using IPV4_DEVCONF_ALL macro to check the state of the arp_process
flag.  This seems wrong, as it implies that either none or all of the network
interfaces accept gratuitous arps.  This patch corrects that, allowing
per-interface arp_accept configuration to deviate from the all setting.  Note
this also brings us into line with the way the arp_filter setting is handled
during arp_process execution.

Tested this myself on my home network, and confirmed it works as expected.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If host is going to autosuspend function with two interfaces and
if IP packet has arrived in-between of two usbnet_suspend() callbacks,
i.e usbnet_resume() is called in-between, tx data flow is stopped.
When autosuspend timer expires and device is put to autosuspend
again, tx queue is waked up and data can be sent again.
This behavior might be repeated several times in a row.

Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Acked-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support to configure the STMMAC ethernet driver via
device-tree instead of platform_data.

Currently, only the properties needed on SPEAr600 are provided. All
other properties should be added once needed on other platforms.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the datatype of "ip_addr" to __be32 as 'ip' should be in
big endian format.

Adapter needs "ip address" in big endian format stored at lower 32bit
of req.word[1]. netxen_config_ipaddr() now receives 'ip' in big endian
format. To satisfy adapter's need, use memcpy() to copy byte by byte
of 'ip' into lower 32bit of req.word[1].

Mac address and serial number of adapter need to be in little endian format.
Change the data type of the related  variables to __le32 / __le64 or cast it
explicitly to __le32 / __le64 depending upon the requirement.
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch removes unused stats member in pxa168 network driver.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

Conflicts:
	drivers/net/wireless/ath/ath9k/hw.c

Changes:
- removed a limit for amount of datagrams for IN NTB
- using pointer to traverse NTB in rx_fixup()
- renamed "temp" to "len" in rx_fixup()
- do NTB sequence number check in rx path
Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes/fixes:
- inform device if max_datagram_size was changed by host
- max_datagram_size can't be bigger MTU in ETH func descr
- fix constants definitions to enable running CAIF service over NCM

Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes:
- use high resolution timer
  latency became approx. 10-15 times less than before
- use taklet for sending remaining data in tx path
Tested on Intel/ARM.
Reviewed-by: NSjur Brændeland <sjur.brandeland@stericsson.com>
Tested-by: NDmitry Tarnyagin <Dmitry.Tarnyagin@stericsson.com>
Signed-off-by: NAlexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asix_rx_fixup() is complex, and does some unnecessary memory copies (at
least on x86 where NET_IP_ALIGN is 0)

Also, it tends to provide skbs with a big truesize (4096+256 with
MTU=1500) to upper stack, so incoming trafic consume a lot of memory and
I noticed early packet drops because we hit socket rcvbuf too fast.

Switch to a different strategy, using copybreak so that we provide nice
skbs to upper stack (including the NET_SKB_PAD to avoid future head
reallocations in some paths)

With this patch, I no longer see packets drops or tcp collapses on
various tcp workload with a AX88772 adapter.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Aurelien Jacobs <aurel@gnuage.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Reviewed-by: NGrant Grundler <grundler@chromium.org>
Reviewed-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

libertas provides a dump_survey implementation based on reading of
a RSSI value. However, this RSSI value is calculated based on the
last received beacon from the associated AP - it is not a good
way of surveying a channel in general, and even causes an error
if the card is not associated to a network.

As this is not appropriate as a survey, remove it. This fixes an
issue where something in userspace is repeatedly calling site-survey
during boot, resulting in many repeated errors as the RSSI value cannot
be read before associating.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Makes them more readable and reduces code size
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These arrays are unused
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver can just check the mask directly
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

uapsd_queues and uapsd_max_sp_len are relevant only for managed
interfaces, and can be configured differently for each vif.

Move them from the local struct to sdata->u.mgd, and update
the debugfs functions accordingly.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some debugfs write functions call kstrto* functions, which
assume the string is null-terminated. Make it valid by changing
ieee80211_if_write() to use static buffer instead of allocating
one, and set the last char to NULL.

(The write functions try to parse some integer/mac address,
so 64 bytes buffer should be enough)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current max throughput rate is known to be good as otherwise it
wouldn't be the max throughput rate. Since rate sampling can introduce
some overhead (by adding RTS for example or due to not aggregating the
frame) don't sample the max throughput rate.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TX status fifo is limited to 16 elements. When we send more frames than
that, we can easily loose status, what is not good for rate scaling
algorithm.

On my testing the change does not degrade performance, actually make
is slightly better. Additionally with the patch I can see much less
various rt2x00 warnings in dmesg.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tx statuses of aggregated subframes contain packetid of first subframe
in the AMPDU. We can not identify AMPDU subframes based on packedid, so
simply assume that status match first pending frame in the queue. Thats
mostly the same what 2800pci do.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>